Teknik Hampstead Park 5420731 User manual

www.teknikoffice.co.uk
Desk
Hampstead Park Collection | Model 5420731
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-38
Français p 39-43
Español p 44-48
Business or pleasure.
Works both ways.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6-38
39-43
44-48
49-50
51
Hammer
Not actual size
Skip the power trip.
This time.
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BACK (1)
G SMALL BACK (1)
H SHELF (1)
I RIGHT BOTTOM (1)
J LEFT BOTTOM (1)
K ADJUSTABLE SHELF (1)
L SMALL SHELF (1)
M TOP MOLDING (1)
N RIGHT LEG (1)
O LEFT LEG (1)
P STRETCHER (1)
Q DOOR (1)
R PENCIL DRAWER FRONT (1)
S PENCIL RIGHT DRAWER SIDE (1)
T PENCIL LEFT DRAWER SIDE (1)
U PENCIL DRAWER BACK (1)
V PENCIL DRAWER BOTTOM (1)
W PENCIL DRAWER BRACE (1)
X DRAWER FRONT (1)
Y RIGHT DRAWER SIDE (1)
Z LEFT DRAWER SIDE (1)
AA DRAWER BACK (1)
BB DRAWER BOTTOM (1)
CC FILE DRAWER FRONT (1)
DD FILE RIGHT DRAWER SIDE (1)
EE FILE LEFT DRAWER SIDE (1)
FF FILE DRAWER BACK (1)
GG FILE DRAWER BOTTOM (1)
Pae 2

Part Identification
A
B
C
D
E
FG
H
I
J
K
M
N
O
P
Q
R
S
U
V
L
T
W
Y
Z
X
AA
BB
CC
DD
EE
FF
GG
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HH LONG EXTENSION
RAIL - 2 II LONG EXTENSION SLIDE - 2
(EXTENSION SET
SHOWN SEPARATED)
LEFT CABINET
RAIL - 1
2
RIGHT CABINET
RAIL - 1
1
LEFT DRAWER
SLIDE - 1
4
RIGHT DRAWER
SLIDE - 1
3
JJ EXTENSION RAIL - 2 KK EXTENSION SLIDE - 2
(EXTENSION SET
SHOWN SEPARATED)
HIDDEN
CAM - 41
8ANGLED HEAD
CAM SCREW - 41
9
Anled head
SMALL HIDDEN
CAM - 14
10 STRAIGHT HEAD
CAM SCREW - 14
11
Straiht head
5FILE
GLIDE - 2 6FILE HANGER SET  1 7FRONT FILE HANGER  1
WOOD DOWEL - 50
12 KNOB - 5
15
HINGE - 2
13 HINGE
BRACKET - 2
14
GROMMET - 1
16 APPLIQUE
CARD - 1
17 METAL PIN/
RUBBER SLEEVE SET - 4
18
Pae 4
28 ASSEMBLY
TOOL  1

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
19 BLACK 112" FLAT HEAD SCREW  19
SILVER 1/2" FLAT HEAD SCREW - 4
27
BLACK 1/2" FLAT HEAD SCREW - 12
26
BLACK 1-1/16" WAFER HEAD SCREW - 4
29
BLACK 9/16" WAFER HEAD SCREW - 16
23
BLACK 1/2" PAN HEAD SCREW - 27
25
24 BLACK 12" MACHINE SCREW  4
22 BLACK 78" MACHINE SCREW  5
20 BLACK 138" MACHINE SCREW  2
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Turn two ANGLED HEAD CAM SCREWS (9) into the exact
holes shown in the LEFT UPRIGHT (D).
å Fasten the LEFT CABINET RAIL (2) to the LEFT UPRIGHT (D).
Use three BLACK 1/2" FLAT HEAD SCREWS (26).
Anled head
D
Rounded corner
BLACK 1/2" FLAT HEAD SCREW
(3 used in this step)
26
9
Roller end
2
2
Use these holes.
Some assembly
(and snacks) required.
Pae 6
Surface with fewer holes

Step 2
å Turn the LEFT UPRIGHT (D) over.
å Separate the EXTENSION SLIDES (II and KK) from the EXTENSION RAILS (HH and JJ) as shown in the enlared
diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (HH and JJ) to the LEFT UPRIGHT (D). Use six BLACK 1/2" PAN HEAD SCREWS (25).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL out to find the other two holes that line up with the holes in the UPRIGHT. Turn a
SCREW into those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Turn two ANGLED HEAD CAM SCREWS (9) into the exact holes shown in the LEFT UPRIGHT (D).
å Insert two WOOD DOWELS (12) into the LEFT UPRIGHT (D).
Pull up or down on the black lever and pull the SLIDE from the RAIL.
JJ
KK
Use these holes.
Anled head
9
Rounded corner
12
Open end
BLACK 12" PAN HEAD SCREW
(6 used in this step)
25
D
JJ
HH
Pae 7
Surface with more holes

å Turn two ANGLED HEAD CAM SCREWS (9) into the exact holes
shown in the RIGHT UPRIGHT (C).
å Fasten the RIGHT CABINET RAIL (1) to the RIGHT UPRIGHT (C).
Use three BLACK 1/2" FLAT HEAD SCREWS (26).
å Turn the RIGHT UPRIGHT (C) over and turn four ANGLED HEAD CAM
SCREWS (9) into the exact holes shown in the RIGHT UPRIGHT.
å Insert two WOOD DOWELS (12) into the RIGHT UPRIGHT (C).
Step 3
1
Use these holes.
12
C
C
Rounded corner
Anled head
9
BLACK 1/2" FLAT HEAD SCREW
(3 used in this step)
26
9
Roller end
Pae 8
Surface with
fewer holes
Surface with
more holes
1

Step 4
å Insert twenty-three WOOD DOWELS (12) into the
SMALL BACK (G), SHELVES (H and L), and BOTTOMS (I
and J).
H
I
J
L
G
12
12
12
(23 used)
12
Pae 9

Step 5
C
H
D
å Insert four HIDDEN CAMS (8) into the holes in the SHELF (H)
as shown.
å Fasten the SHELF (H) to the UPRIGHTS (C and D). Tihten four
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert into
the holes in the UPRIGHTS. 321
The arrow must
point toward the
ede of the board.
8
8
Rounded corner
Rounded corner
Pae 10
Surface with
HIDDEN CAMS
Surface with
fewer holes
Surface with
more holes