Teknik Hampstead Park 5423704 User manual

www.teknikoffice.co.uk
Hampstead Park Wall Desk
Model 5423704
For things 'n such.
Teknik

Table of Contents Assembly Tools Required
2
3
4-7
8
9
10
11
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
APPLIQUE CARD - 2
3
DRYWALL ANCHOR - 2
2
BLACK 2-3/8" FLAT HEAD SCREW - 2
4BLACK 1" LARGE HEAD SCREW - 2 5
Page 2
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Electric drill with 1/8"
and 1/4" bits
(ONLY in indicated step)
Pencil
Tape Measure
Level

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A WALL SUPPORT (1)
B WALL UNIT (1)
Now you know
our ABCs.
Page 3
A
B

Step 1
å Your Wall Desk is intended to be fastened to wall studs using the included hardware.
å If you need to drywall hang this unit, purchase a drywall anchor which is rated to support a MINIMUM of
80 lbs. Follow the instructions provided with the anchoring hardware.
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å Determine the desired height of the Wall Desk on your wall and subtract 5-5/8". Mark this location on your
wall. This will be the bottom edge of the WALL SUPPORT (A).
å Locate and mark the wall stud locations on your wall.
å NOTE: BE SURE THE TWO MARKS ON THE STUDS ARE LEVEL BEFORE DRILLING.
å Drill a 1/8" hole in your wall at each wall stud location.
å Fasten the WALL SUPPORT (A) to your wall using two BLACK 2-3/8" FLAT HEAD SCREWS (4) into the
exact holes shown.
Page 4
Wall stud
A
BLACK 2-3/8" FLAT HEAD SCREW
(2 used in this step)
4
Angled edge

StepStep 2
å There are two brackets already fastened to your unit. These brackets
will help secure the WALL UNIT (B) firmly against the wall.
å Temporarily hang your unit on the WALL SUPPORT (A).
å Make a mark on the wall through the brackets with your pencil.
Page 5
B
A
Make a mark on the wall
through the brackets.

Step 3
å Remove your unit from the WALL SUPPORT (A).
å Peel APPLIQUES from the APPLIQUE CARDS (3) and stick them onto
each visible SCREW head and unused hole in the WALL SUPPORT (A).
å Drill a 1/4" hole in your wall in the marked locations for the brackets.
å Turn the DRYWALL ANCHORS (2) into these holes until they are flush
with the wall.
å Hang the WALL UNIT (B) back on the WALL SUPPORT (A).
å Securely fasten the WALL UNIT (B) to your wall using two BLACK
1" LARGE HEAD SCREWS (5) through the brackets and into the
DRYWALL ANCHORS.
Page 6
To cover screws and holes
3
A
2
B
BLACK 1" LARGE HEAD SCREW
(2 used in this step)
5

å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Step 4
Page 7
10 lbs.
15 lbs.
25 lbs.
15 lbs.

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Properly mounting the unit to the wall. • If not properly mounted, the unit can fall
from the wall and cause injury and damage. • Carefully review and follow the mounting instructions contained in this manual.
• Overloaded shelves. • Risk of injury or property damage.
• Overloaded furniture can break. • Never exceed the weight limits shown in the instructions.
• Improper use of furniture to support TV’s.
• Placing TV’s on furniture items not
intended to support them is hazardous.
• Risk of injury or death. TV’s can be very
heavy. Plus the weight and location of
the picture screen can make furniture tip
forward.
• This product is not designed to support a
television.