Teknik Executive Trestle Desk 5424128 User manual

www.teknikoffice.co.uk
Business or pleasure.
Works both ways.
Executive Trestle Desk
| Model 5424128
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-28
29-32
33-36
37-38
39
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3
A UPPER RIGHT END (2)
B UPPER LEFT END (2)
C2 LOWER RIGHT END (2)
D2 LOWER LEFT END (2)
D18 SMALL RIGHT DRAWER SIDE (2)
D19 SMALL LEFT DRAWER SIDE (2)
D28 LARGE RIGHT DRAWER SIDE (2)
D29 LARGE LEFT DRAWER SIDE (2)
D66 SMALL DRAWER BACK (2)
D151 LARGE DRAWER BACK (2)
D954 DRAWER BOTTOM (4)
E TOP (1)
F BOTTOM (2)
G SHELF (2)
H LARGE BACK (1)
I2 LOWER BACK (2)
J BACK (2)
K2 RIGHT FRONT LEG (2)
L2 LEFT FRONT LEG (2)
M2 RIGHT REAR LEG (1)
N2 CENTER RIGHT REAR LEG (1)
O2 LEFT REAR LEG (1)
P2 CENTER LEFT REAR LEG (1)
Q SKIRT (4)
R2 LARGE DRAWER FRONT (2)
W SMALL DRAWER FRONT (2)
A
A
B
BC
C2
D2
D
E
F
F
G
H
I2
I2
J
J
K2
K2
L2
L2
M2
N2
O2
QQ
Q
QD18
D66
D19
D954
D28
D151
D29 D954
R2
W
D18
D66
D19
D954
D28
D151
D29 D954
R2
W
G
P2

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GROMMET CAP - 1
39P CAM COVER - 2 75P
12F TWIST-LOCK®
FASTENER - 4
10A SLIDE CAM - 8
PULL - 4
176K
CAM
SCREW - 18
8F
CORD CLIP - 4
31P GROMMET - 1 38P
HIDDEN CAM - 42
1F CAM DOWEL - 24 2F
CC RIGHT CABINET
RAIL - 2 DD LEFT CABINET RAIL - 2 FF LEFT DRAWER SLIDE - 2
EE RIGHT DRAWER
SLIDE - 2
FILE GLIDE - 4
15B
424128 www.sauder.com/servicesPage 4
FILE ROD - 4
7B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
35MA EXTENSION SLIDE - 4 35MC
METAL
BRACKET - 12
4G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 1-1/8" PAN HEAD SCREW - 16
9S
SILVER 1/2" MACHINE SCREW - 8
38S
BLACK 9/16" LARGE HEAD SCREW - 24
1S BLACK 1-7/8" FLAT HEAD SCREW - 12 2S
3S GOLD 5/16" FLAT HEAD SCREW - 32
30S BLACK 1-9/16" FLAT HEAD SCREW - 16

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (12F) into the large holes in the BACKS (H and J).
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(4 used)
12F
H
J
J
Page 6

Step 2
Arrow
1F
2F
1F
2F
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(24 used)
Ax 2
Bx 2
Page 7
å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A, B,
C2, and D2) and LOWER BACKS (I2). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM.
å NOTE: There are two of each of these parts (A, B, C2, D2, and I2).
C2 x 2
I2 x 2
D2 x 2

å Push the remaining eighteen HIDDEN CAMS (1F) into the
BOTTOMS (F), SHELVES (G), and LARGE BACK (H).
Step 3
Do not tighten the HIDDEN CAMS in this step.
Arrow
Arrow
1F
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
(18 used)
F
F
G
G
H
Page 8

Step 4
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Finished edge
Finished edge
Remember:
Righty tighty.
Lefty loosey.
Push the black lever in and pull the SLIDE from the RAIL.
35MA35MC
1
2
3
3
2
1
Page 9
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (35MA) to a LOWER END (C2 and D2). Use four
GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the
enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL out to find
the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
å Repeat this step for the remaining LOWER ENDS (C2 and D2).
C2 x 2
D2 x 2

Step 5
Page 10
å Turn eighteen CAM SCREWS (8F) into
the LEGS (K2, L2, M2, N2, O2, and P2).
8F
8F
(18 used)
K2
K2
L2
L2
M2
N2
O2
P2