Teknik 5402174 User manual

For all your
newfangled gadgetry.
Traditional Computer Workcentre
Model 5402174
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-6
7-24
33-34
35
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B2 LEFT END (1)
C UPRIGHT (1)
D TOP (1)
D28 RIGHT DRAWER SIDE (1)
D29 LEFT DRAWER SIDE (1)
D78 DRAWER BACK (1)
D707 DRAWER BOTTOM (1)
E MODESTY PANEL (1)
F SHELF (1)
G BACK (1)
H2 KEYBOARD SHELF (1)
I2 KEYBOARD FRONT (1)
J BRACE (2)
K DOOR (1)
Q TOP MOLDING (1)
R END MOLDING (1)
S BASE MOLDING (1)
A
B2
C
D
E
F
G
H2
I2
J
J
K
Q
R
S
Page 3
D707
D28
D29
D78
L

Hardware Identification
ANGLE BRACKET - 14
NN
EXTENSION BRACKET - 2
DD
CORD CLIP - 1
PP METAL PIN - 2 QQ RR SLIDE CAM - 2
PULL - 2
MM
JJ
HINGE SPACER - 2 HANDLE - 2
KK HANDLE MOUNT - 4 LL
CAM SCREW - 2
8F
HIDDEN CAM - 12
1F
CAM DOWEL - 10
2F
TLONG RIGHT CABINET RAIL - 1 ULONG LEFT CABINET RAIL - 1
WLONG LEFT DRAWER SLIDE -1
VLONG RIGHT DRAWER SLIDE - 1
FILE ROD - 2
CC
35AW CABINET RIGHT - 1 35AY DRAWER RIGHT - 1
35AZ DRAWER LEFT - 1
35AX CABINET LEFT - 1
FELT DISC CARD - 1
SS
Page 4
FILE GLIDE - 2
15B
KEYBOARD
HINGE- 2
12HHH HINGE - 2 DOOR STOP - 1 4I

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-7/8" FLAT HEAD SCREW - 2
TT
SILVER 7/8" MACHINE SCREW - 2
WW SILVER 3/4" MACHINE SCREW - 2 XX
SILVER 1-1/8" FLAT HEAD SCREW - 4
UU
YY SILVER 5/8" MACHINE SCREW - 2
GOLD 9/16" LARGE HEAD SCREW - 32
AAA
VV BROWN 1" FLAT HEAD SCREW - 4
SILVER 5/8" FLAT HEAD SCREW - 8
ZZ
SILVER 9/16" LARGE HEAD SCREW - 2
BBB
NAIL - 20
DDD
GOLD 5/16" FLAT HEAD SCREW - 12
CCC
402174www.sauder.com/services Page 5
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twelve HIDDEN CAMS (1F) into the ENDS (A
and B2), UPRIGHT (C), MODESTY PANEL (E), and
SHELF (F). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM, except for the
HIDDEN CAMS in the MODESTY PANEL.
Page 6
Arrow
1F
2F
(12 used)
(10 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into this edge.
A
C
E
F
B2

Step
Page 7
å Fasten three ANGLE BRACKETS (NN) to the LEFT END (B2).
Use three GOLD 9/16" LARGE HEAD SCREWS (AAA).
å Fasten the END MOLDING (R) to the ANGLE BRACKETS (NN).
Use three GOLD 9/16" LARGE HEAD SCREWS (AAA).
å NOTE: There are no pre-drilled holes in the END
MOLDING (R). The SCREWS will tighten into the groove.
Step 2
NN
GOLD 9/16" LARGE HEAD SCREW
(6 used in this step)
AAA
R
B2
These edges must be even.
Remember:
Righty tighty.
Lefty loosey.

Step
å Fasten two EXTENSION BRACKETS (DD) to the LEFT END (B2).
Use four GOLD 9/16" LARGE HEAD SCREWS (AAA).
å Fasten the CABINET RIGHT (35AW) to the UPRIGHT (C)
and the CABINET LEFT (35AX) to the LEFT END (B2).
Use four GOLD 5/16" FLAT HEAD SCEWS (CCC).
Step 3
Page 8
Finished edge
DD
GOLD 9/16" LARGE HEAD SCREW
(4 used in this step)
AAA
C
B2
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RAILS
CCC
Surface with HIDDEN CAMS
Surface without
HIDDEN CAMS
Roller end
Roller end

Step
Page 9
å Fasten the LONG RIGHT CABINET RAIL (T) to the RIGHT
END (A) and the LONG LEFT CABINET RAIL (U) to the
opposite surface of the UPRIGHT (C). Use four GOLD
5/16" FLAT HEAD SCREWS (CCC).
å NOTE: The CABINET RAILS are marked "CABINET
RIGHT" and "CABINET LEFT" for easy identification.
å Fasten two ANGLE BRACKETS (NN) to the RIGHT
END (A) and UPRIGHT (C). Use two GOLD 9/16" LARGE
HEAD SCREWS (AAA).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the END and UPRIGHT.
Step 4
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RAILS
CCC
A
C
T
U
Finished edge
Finished edge
GOLD 9/16" LARGE HEAD SCREW
(2 used for the ANGLE BRACKETS)
AAA
NN
NN
Surface with HIDDEN CAMS Surface with HIDDEN CAMS

Step
å Turn two CAM SCREWS (8F) into the LEFT END (B2).
å Fasten the TOP MOLDING (Q) to the TOP (D). Use four SILVER 1-1/8"
FLAT HEAD SCREWS (UU).
å NOTE: Do not overtighten the SCREWS.
å Insert a METAL PIN (QQ) into the hole in the TOP (D).
å Fasten the LEFT END (B2) to the TOP (D). Tighten two HIDDEN CAMS.
å NOTE: Be sure the METAL PIN inserts into the hole in the LEFT END (B2).
Step 5
Page 10
8F
B2
B2
D
QQ
SILVER 1-1/8" FLAT HEAD SCREW
(4 used in this step)
UU
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Q
Q
Curved edge
Curved edge