Tektronix TDS3000C Series User manual

xx
TDS3000C Series
Digital Phosphor Oscilloscopes
ZZZ
User Manual
*P071230803*
071-2308-03

TDS3000C Series
Digital Phosphor Oscilloscopes
ZZZ
User Manual
xx
Issued: September 2009
REPRODUCTION AND DISTRIBUTION OF THIS
TECHNICAL MANUAL IS AUTHORIZED FOR UNITED
STATES OF AMERICA GOVERNMENT PURPOSES.
www.tektronix.com
071-2308-03

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TEKPROBE, and TekSecure are registered trademarks of Tektronix, Inc.
DPX, WaveAlert, e*Scope, and OpenChoice are trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Warranty
Tektronix warrants that the product will be free from defects in materials and workmanship for a period of three (3)
years from the date of original purchase from an authorized Tektronix distributor. If the product proves defective
during this warranty period, Tektronix, at its option, either will repair the defective product without charge for
parts and labor, or will provide a replacement in exchange for the defective product. Batteries are excluded from
this warranty. Parts, modules and replacement products used by Tektronix for warranty work may be new or
reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix,
shipping charges prepaid, and with a copy of customer proof of purchase. Tektronix shall pay for the return of the
product to Customer if the shipment is to a location within the country in which the Tektronix service center is
located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for
products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W16 – 15AUG04]

Table of Contents
General Safety Summary ......................................................................................... iii
Compliance Information........................................................................................... v
EMC Compliance.............................................................................................. v
Safety Compliance........................................................................................... vii
Environmental Considerations .............................................................................. ix
Preface .............................................................................................................. xi
Getting Started ................... .................. ...................... .................. .................. ....... 1
Initial Setup........ .......... .......... .......... .............................................. .......... ....... 1
Product and Feature Description............................................................................. 5
Operating Positions............................................................................................ 8
Connecting Power ............................................................................................. 9
Installing an Application Module ....... ...................... .................. ............................ 13
Installing the Communication Module ............... .................. .................................... 13
Front-Panel Menus and Controls............................................................................ 15
Front-Panel Connectors ...................................................................................... 23
Rear-Panel Connectors....................................................................................... 24
Communication Module Connectors ....................................................................... 24
Application Examples............................................................................................. 27
Taking Simple Measurements............................................................................... 27
Analyzing Signal Detail...................................................................................... 33
Taking FFT Measurements .................................................................................. 39
Triggering on a Video Signal................................................................................ 41
Capturing a Single-Shot Signal ............................................................................. 43
Saving Data to a USB Flash Drive.......................................................................... 46
Reference........................................................................................................... 51
Acquisition Controls.............. .................. ................................ .................. ........ 51
Cursor.......................................................................................................... 59
Display......................................................................................................... 63
Hard Copy ..................................................................................................... 65
Horizontal Controls........................................................................................... 67
Math and FFT................................................................................................. 72
Measure........................................................................................................ 79
QuickMenu.................................................................................................... 84
Save/Recall.................................................................................................... 84
Trigger Controls............................................................................................... 90
Utility .... .......... .......................................................................... .......... ...... 109
Vertical Controls ............................................................................................ 114
e*Scope Web-Based Remote Control .................................................................... 118
TDS3000C Series Oscilloscope User Manual i

Table of Contents
Appendix A: Specifications .................................................................................... 121
Appendix B: Factory Setup..................................................................................... 131
Appendix C: Accessories....................................................................................... 135
Appendix D: Probe Basics...................................................................................... 139
Probe Descriptions.......................................................................................... 139
Probe Compensation........................................................................................ 139
TekProbe Interface.......................................................................................... 140
Probe Guard ................................................................................................. 140
Ground Leads ............................................................................................... 140
P3010 High-Frequency Compensation................................................................... 142
P3010 Replaceable Parts and Accessories ............................................................... 143
P6139A Replaceable Parts and Accessories ............................................................. 144
Using Other Probes......................................................................................... 145
Supported Active Probes and Adapters .................................................................. 145
Unsupported Probes ........................................................................................ 146
Appendix E: General Care and Cleaning ..................................................................... 147
Appendix F: Ethernet Setup.................................................................................... 149
Your Ethernet Network Information...................................................................... 149
Entering the Ethernet Network Settings.................................................................. 150
Entering the Network Printer Settings.................................................................... 151
Testing Your Ethernet Connection........................................................................ 151
Troubleshooting Your Ethernet Connection ............................................................. 152
The Instrument Setup Screen.............................................................................. 153
The Printer Configuration Screen......................................................................... 154
The Add Printer Screen .................................................................................... 155
Ethernet Error Messages................................................................................... 156
Ethernet Settings Form ... ...................... ...................... ...................... ................ 157
Index
ii TDS3000C Series Oscilloscope User Manual

General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or Personal
Injury
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Connect the probe output to the measurement
instrument before connecting the probe to the circuit under test. Connect the
probe reference lead to the circuit under test before connecting the probe input.
Disconnect the probe input and the probe reference lead from the circuit under test
before disconnecting the probe from the measurement instrument.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Connect the probe reference lead to earth ground only.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Do Not Operate With Suspected Failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Replace Batteries Properly. Replace batteries only with the specified type and
rating.
Recharge Batteries Properly. Recharge batteries for the recommended charge
cycle only.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
TDS3000C Series Oscilloscope User Manual iii

General Safety Summary
TermsinthisManual These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Symbols and Terms on the
Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the marking.
WARN ING indicates an injury hazard not immediately accessible as you
read the marking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
iv TDS3000C Series Oscilloscope User Manual

Compliance Information
This section lists the EMC (electromagnetic compliance), safety, and
environmental standards with which the instrument complies.
EMC Compliance
EC Declaration of
Conformity – EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 61326-1:2006, EN 61326-2-1:2006. EMC requirements for electrical equipment
for measurement, control, and laboratory use. 123
CISPR 11:2003. Radiated and conducted emissions, Group 1, Class A
IEC 61000-4-2:2001. Electrostatic discharge immunity
IEC 61000-4-3:2002. RF electromagnetic field immunity 4
IEC 61000-4-4:2004. Electrical fast transient/burst immunity
IEC 61000-4-5:2001. Power line surge immunity
IEC 61000-4-6:2003. Conducted RF immunity 5
IEC 61000-4-11:2004. Voltage dips and interruptions immunity 6
EN 61000-3-2:2006. AC power line harmonic emissions
EN 61000-3-3:1995. Voltage changes, fluctuations, and flicker
European Contact.
Tektronix UK, Ltd.
Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom
1This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic
interference.
2Emissions which exceed the levels required by this standard may occur when this equipment is connected to a
test object.
3To ensure compliance with the EMC standards listed here, high quality shielded interface cables should be used.
4Theincreaseintracenoisewhilesubjectedtoatestfield(3V/moverthefrequencyrange80MHzto1GHz,
1.4GHzto2.0GHzand1V/mfrom2.0GHzto2.7GHz,with8
0% amplitude modulation at 1 kHz) is not to
exceed 8 major divisions peak-to-peak. Ambient conducted field may induce triggering when the trigger threshold
is offset less than 4 major divisions from ground reference for the IEC 61000-4-3 test.
5Theincreaseintracenoisewhilesubjectedtoatestfield (3 V/rms over the frequency range 150 kHz to 80 MHz,
with 80% amplitude modulation at 1 kHz) is not to exceed 2 major divisions peak-to-peak. Ambient conducted
TDS3000C Series Oscilloscope User Manual v

Compliance Information
field may induce triggering when the trigger threshold is offset less than 1 major division from ground reference for
the IEC 61000-4-6 test.
6Performance Criterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle Voltage-Interruption test
levels (IEC 61000-4-11).
Australia / New Zealand
Declaration of
Conformity – EMC
Complies with the EMC provision of the Radiocommunications Act per the
following standard, in accordance with ACMA:
CISPR 11:2003. Radiated and Conducted Emissions, Group 1, Class A, in
accordance with EN 61326-1:2006 and EN 61326-2-1:2006.
vi TDS3000C Series Oscilloscope User Manual

Compliance Information
Safety Compliance
EC Declaration of
Conformity – Low Voltage
Compliance was demonstrated to the following specification as listed in the
Official Journal of the European Communities:
Low Voltage Directive 2006/95/EC.
EN 61010-1: 2001. Safety requirements for electrical equipment for
measurement control and laboratory use.
U.S. Nationally Recognized
Testing Laboratory Listing
UL61010B-1:2003, First Edition, Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use.
Canadian Certification CAN/CSA C22.2 No. 1010.1-92 - Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use. CAN/CSA
C22.2 No. 1010.1B 97 - Amendment 2 to CAN/CSA C22.2 No. 1010.1-92
- Safety Requirements for Electrical Equipment for Measurement, Control,
and Laboratory Use.
Additional Compliances IEC 61010-1: 2001. Safety requirements for electrical equipment for
measurement, control, and laboratory use.
Equipment Type Test and measuring equipment.
Safety Class Class1–groundedproduct.
Pollution Degree
Description
A measure of the contaminants that could occur in the environment around
and within a product. Typically the internal environment inside a product is
considered to be the same as the external. Products should be used only in the
environment for which they are rated.
Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs.
Products in this category are generally encapsulated, hermetically sealed, or
located in clean rooms.
Pollution Degree 2. Normally only dry, nonconductive pollution occurs.
Occasionally a temporary conductivity that is caused by condensation must
be expected. This location is a typical office/home environment. Temporary
condensation occurs only when the product is out of service.
Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution
that becomes conductive due to condensation. These are sheltered locations
TDS3000C Series Oscilloscope User Manual vii

Compliance Information
where neither temperature nor humidity is controlled. The area is protected
from direct sunshine, rain, or direct wind.
Pollution Degree 4. Pollution that generates persistent conductivity through
conductive dust, rain, or snow. Typical outdoor locations.
Pollution Degree Pollution Degree 2 (as defined in IEC 61010-1). Note: Rated for indoor use only.
Installation (Overvoltage)
Category Descriptions
Terminals on this product may have different installation (overvoltage) category
designations. The installation categories are:
Measurement Category IV. For measurements performed at the source of
low-voltage installation.
Measurement Category III. For measurements performed in the building
installation.
Measurement Category II. For measurements performed on circuits directly
connected to the low-voltage installation.
Measurement Category I. For measurements performed on circuits not
directly connected to MAINS.
Overvoltage Category Overvoltage Category II (as defined in IEC 61010-1).
viii TDS3000C Series Oscilloscope User Manual

Compliance Information
Environmental Considerations
This section provides information about the environmental impact of the product.
Product End-of-Life
Handling
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and
use of natural resources. The equipment may contain substances that could be
harmful to the environment or human health if improperly handled at the product’s
end of life. In order to avoid release of such substances into the environment and
to reduce the use of natural resources, we encourage you to recycle this product
in an appropriate system that will ensure that most of the materials are reused or
recycled appropriately.
This symbol indicates that this product complies with the applicable European
Union requirements according to Directives 2002/96/EC and 2006/66/EC
on waste electrical and electronic equipment (WEEE) and batteries. For
information about recycling options, check the Support/Service section of the
Tektronix Web site (www.tektronix.com).
Battery Recycling. This product might contain an optional lithium ion (Li-ion)
rechargeable battery, which must be recycled or disposed of properly.
Lithium-Ion batteries are subject to disposal and recycling regulations that
vary by country and region. Always check and follow your applicable
regulations before disposing of any battery. Contact Rechargeable Battery
Recycling Corporation (www.rbrc.org) for U.S.A. and Canada, or your local
battery recycling organization.
Many countries prohibit the disposal of waste electronic equipment in
standard waste receptacles.
Place only discharged batteries in a battery collection container. Use electrical
tape or other approved covering over the battery connection points to prevent
short circuits.
Mercury Notification. This product uses an LCD backlight lamp that contains
mercury. Disposal may be regulated due to environmental considerations. Please
contact your local authorities or, within the United States, refer to the E-cycling
Central Web page (www.eiae.org) for disposal or recycling information.
Transporting Batteries The capacity of the optional lithium ion rechargeable battery pack in this product
is under 100 Wh. The lithium-equivalent content, as definedbytheUNManual
of Tests and Criteria Part III Section 38.3, is under 8 g per pack and 1.5 g per
individual cell.
TDS3000C Series Oscilloscope User Manual ix

Compliance Information
Always check all applicable local, national, and international regulations
before transporting a Lithium-Ion battery.
Transporting an end-of-life, damaged, or recalled battery may, in certain
cases, be specifically limited or prohibited.
Restriction of Hazardous
Substances
This product has been classified as Monitoring and Control equipment, and is
outside the scope of the 2002/95/EC RoHS Directive.
x TDS3000C Series Oscilloscope User Manual

Preface
This manual contains operating information for the TDS3000C Series Digital
Storage Oscilloscopes. The manual consists of the following chapters:
The Getting Started chapter briefly describes features of the oscilloscope
and provides installation instructions.
The Application Examples chapter provides examples on how to solve a
variety of measurement problems.
The Reference chapter describes the selections or available range of values
for each option.
The Appendix A: Specifications chapter includes electrical, environmental,
and physical specifications for the oscilloscope, as well as certifications and
compliances.
The Appendix B: Factory Setup chapter contains a list of the menus and
controls with the default settings that the oscilloscope recalls when you push
the Save/Recall front-panel button, and then the Recall Factory Setup screen
button.
The Appendix C: Accessories chapter briefly describes standard and optional
accessories.
The Appendix D: Probe Basics chapter provides basic information on the
P3010 and the P6139A probes, and on other probes.
The Appendix E: Cleaning chapter describes how to take care of the
oscilloscope.
The Appendix F: Ethernet Setup chapter describes how to set up the
oscilloscope for printing through the network, and remote programming.
TDS3000C Series Oscilloscope User Manual xi

Preface
Preventing Electrostatic
Damage
CAUTION. Electrostatic discharge (ESD) can damage components in the
oscilloscope and its accessories. To prevent, ESD, observe these precautions
when directed to do so.
Use a Ground Strap. Wear a grounded, antistatic wrist strap to discharge the static
voltage from your body while installing or removing sensitive components.
UseaSafeW
ork Area. Do not use any devices capable of generating or holding a
static charge in the work area where you install or remove sensitive components.
Avoid handling sensitive components in areas that have a floor or benchtop
surface capable of generating a static charge.
Handle Components Safely. Do not slide sensitive components over any surface.
Do not touch exposed connector pins. Handle sensitive components as little as
possible.
Transport and Store Carefully. Transport and store sensitive components in a
static-protected bag or container.
xii TDS3000C Series Oscilloscope User Manual

Preface
Firmware Updates Through
the Internet
If a newer version of firmware becomes available, you can use the Internet and a
USB flash drive to update your oscilloscope.
To update the firmware, follow these steps:
1. From your computer, access the www.tektronix.com Web site and check if a
newer version of oscilloscope firmware is available.
If there is a newer version of firmware, download the firmware file from the
web page. Unzip and copy the tds3000c.img file into the root folder of a
USB flash drive.
2. Power off your oscilloscope.
3. Insert the USB flash drive into the flash drive port on the front of the
oscilloscope.
4. Power on your oscilloscope.
5. When prompted, push the OK Load New Firmware menu button to start
the firmware load process.
NOTE. Do not power off the oscilloscope or remove the USB flash drive until the
oscilloscope finishes installing the firmware.
6. Wait for the oscilloscope to reboot itself.
7. When prompted, remove the USB flash drive.
8. Push the Utility front-panel button.
9. Push the Version bottom button. The oscilloscope displays the firmware
version number.
10. Confirm that the version number matches that of the new firmware.
TDS3000C Series Oscilloscope User Manual xiii

Preface
xiv TDS3000C Series Oscilloscope User Manual