Tennsco Industrial Workbench with Steel Top Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
PK-1291018PK-1291018
Industrial Workbench
with Steel Top
PLEASE NOTE: These instructions are for a workbench
with ared or adjustable legs. If you have ordered a
modular workbench (with modular door or drawer units
instead of legs) please disregard these instructions and
assemble using the instructions that came with your
modular units.
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIESLOAD CAPACITIES
FOR STELL TOPFOR STELL TOP
48w x 30d
60w x 30d
72w x 30d
96w x 30d
60w x 36d
72w x 36d
96w x 36d
4000 lbs.
2500 lbs.
1800 lbs.
4000 lbs.
2500 lbs.
1800 lbs.
4000 lbs.
UNIT SIZEUNIT SIZE WT. CAPACITYWT. CAPACITY
*96”w workbenches have 3 sets of legs.
NOTE: Additional accessories shown above are
sold separately.

ASSEMBLY OF STEEL TOP INDUSTRIAL WORKBENCH
Two people are recommended for assembly. Approximate assembly time: 40-45 minutes.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
1. Lay the top (Ref. No. 1) face down on two sawhorses or a
protected at surface.
Place a workbench leg (Ref. No. 4) on
the top, aligning the four end holes as shown below. Attach it by
rst threading two
1/4”-20 x 5/8” bolts (Ref. No. 18) through
the leg and the top. Then insert two more bolts through the leg
and top and secure.. Attach the second leg the in the same
manner.
2. The two mounting brackets (Ref. No. 3) are used either for
additional desktop support or to mount a workbench drawer.
If you are adding the drawer to your bench, skip to step 3.
Otherwise, center and attach the two brackets under the lip
of the bench top for extra support, using
one bolt on each end of each bracket.
The brackets should be evenly spaced
for maximum support.
3. Attach the stringer (Ref. No. 2) to the rear legs, skipping the top
two holes and using the next four holes from the top of each leg.
NOTE: The legs are symetrical, so the front and rear of
the bench will be determined by where you place the
stringer.Attach witheight 1/4”-20 x 5/8” bolts, nuts, and lock
washers (Ref. Nos. 18, 19, 20), four on each side.
4. If you purchased only the basic workbench, your bench is now
complete. The remaining instructions show assembly of optional
accessories (such as the workbench drawer, the lower shelf, side
and back rails, or risers).
NOTE: The drawings throughout this instruction sheet show the
ared leg. If your bench came with adjustable legs, the legs
will look different than the drawings shown throughout these
instructions. The drawing here illustrates an example of both
leg styles: the ared leg (shown at right) and the adjustable leg
(shown at left). Both legs will attach the same way to the top.
NOTE: The stringer attaches to the at area of
the leg. For ared legs, this will be on the inside
of each leg; for the adjustable legs, this wil be on
the outside of each leg.









ADJUSTABLE LEG
FLARED LEG
ADJUSTABLE LEG
FLARED LEG
NOTE: If attaching an optional drawer, you may want to leave the
bench in the upside-down position.





1. Remove the drawer (Ref. No. 6) from the drawer housing
(Ref. No. 7).
2. Attach the two mounting brackets (refered to in step 2 on
the previous page) in the desired location on the workbench
top. It is most common to place the drawer to either the far
left or far right side of the bench, but can be placed anywhere
that there are two holes in the bench top that are 15” apart.
Secure with two 1/4”-20 x 5/8” bolts per mounting bracket.
1. If you are installing the optional side and back rails, and
are also installing an optional riser, the riser must be in
position rst. NOTE: The riser and rails share some of
the same bolts and nuts. To avoid having to re-do
parts of the installation, please refer to the riser
instructions as you install the side and back rails.
1. Place the shelf (Ref. No. 12)
on the brace
of each
leg. Attach
with three
1/4”-20 x
5/8” bolts
and nuts
on each
end of the
shelf shown.

OPTIONAL ACCESSORIES
Optional Workbench Drawer

Mounting Bracket slides
under the bench top lip.
Optional Lower Shelf
3. Attach the drawer
housing to the
mounting brackets.
Secure with four
1/4”-20 x 5/8” bolts.


4. With the workbench upright, slide the drawer back into the
drawer housing.
Optional Riser or Electronic Riser
Optional Side and Back Rails
For assembly and installation of a riser or electronic riser,
please refer to the instructions which came with the riser kit.
2. Place a side rail (Ref. No. 13) on one side of the workbench
top, making sure that the rounded edge is toward the front
of the bench. Attach with four 1/4”-20
x 5/8” bolts and nuts along the
bottom edge. Repeat
this step for
the
other
side of the
workbench.
3. Attach the back rail (Ref. No.
14) by placing the ange of the
rail under the bench top. Attach
with eight 1/4”-20 x 5/8” bolts
and nuts along the bottom.
NOTE: Where there is a mounting
bracket under the bench, you will
rst meed to remove the bolt from
the mounting bracket. The bolt will
go through both the back rail and
the mounting bracket. No nut will
be needed in these locations.
4. Attach the back rail
to the side rails, using
two
1/4”-20 x 5/8”
bolts and nuts on
each end.
NOTE: For assembly and installation of a cam lock or padlock hasp,
please refer to the instructions which came with the drawer kit.


REPLACEMENT PARTSREPLACEMENT PARTS
..
REF. NO. DESCRIPTIONREF. NO. DESCRIPTION
PART NUMBERSPART NUMBERS
60”w x 30”d 60”w x 36”d 72”w x 30”d 72”w x 36”d60”w x 30”d 60”w x 36”d 72”w x 30”d 72”w x 36”d
QTY.QTY.
1 Steel Bench Top (with Stringer)
2 Stringer (included with bench top)
3 Mounting Bracket (pair included with top)
4 Flared Workbench Leg (pair) OR
Adjustable Workbench Leg (pair)
5 Optional Drawer (complete unit)
6 *Drawer
7 *Drawer Housing
8 *Padlock Hasp
9
*Tray
10 *Divider
11 *Optional Cam Lock
12 Optional Lower Steel Shelf
13 Optional Side Rail
14 Optional Back Rail
15 Optional Riser Support
16 Optional Riser Shelf
17 Optional Electronic Riser Shelf
18 1/4”-20 x 5/8” Bolt
19 1/4”-20 Nut
20 1/4” Lockwasher
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
24
12
8
T-3060
WBS-60
WBMB-30
L-3230
AL-3230
WBD-1
976CDW
976CDH
976PH
976T
WBDD-12
CL-1
S-60
189SS
189BS
WBRS-2
WBRS-60
EWRS-60
T-3660
WBS-60
WBMB-36
L-3236
AL-3236
WBD-1
976CDW
976CDH
976PH
976T
WBDD-12
CL-1
S-60
404SS
189BS
WBRS-2
WBRS-60
EWRS-60
T-3072
WBS-72
WBMB-30
L-3230
AL-3230
WBD-1
976CDW
976CDH
976PH
976T
WBDD-12
CL-1
S-72
189SS
404BS
WBRS-2
WBRS-72
EWRS-72
T-3672
WBS-72
WBMB-36
L-3236
AL-3236
WBD-1
976CDW
976CDH
976PH
976T
WBDD-12
CL-1
S-72
404SS
404BS
WBRS-2
WBRS-72
EWRS-72
*Included in Ref. No. 5, optional drawer (Part No. WBD 1). **Available Locally
**
**
**
**
**
**
**
**
**
**
**
**
Optional Electronic RiserOptional Electronic Riser
Shelf (Ref No. 17)Shelf (Ref No. 17)
Steel Bench TopSteel Bench Top
(Ref No. 1)(Ref No. 1)
StringerStringer
(Ref No. 2)(Ref No. 2)
Mounting BracketMounting Bracket
(Ref No. 3)(Ref No. 3)
Flared Workbench LegFlared Workbench Leg
(Ref No. 4)(Ref No. 4)
AdjustableAdjustable
WorkbenchWorkbench
LegLeg
(Ref No. 4)(Ref No. 4)
Optional drawerOptional drawer
(Ref No. 5)(Ref No. 5)
Optional Lower ShelfOptional Lower Shelf
(Ref No. 12)(Ref No. 12)
Optional Side RailOptional Side Rail
(Ref No. 13)(Ref No. 13)
Optional Back RailOptional Back Rail
(Ref No. 14)(Ref No. 14)
Optional Riser SupportOptional Riser Support
(Ref No. 15)(Ref No. 15)
Optional Riser ShelfOptional Riser Shelf
(Ref No. 16)(Ref No. 16)
1/4”-20 x 5/8” Bolt
(Ref No. 18)(Ref No. 18)
1/4”-20 Nut
(Ref No. 19)(Ref No. 19)
1/4” Lockwasher
(Ref No. 20)(Ref No. 20)









TrayTray
(Ref No. 9)(Ref No. 9)

DrawerDrawer
(Ref No. 6)(Ref No. 6)
Drawer HousingDrawer Housing
(Ref No. 7)(Ref No. 7)


Padlock HaspPadlock Hasp
(Ref No. 8)(Ref No. 8)


Optional Cam LockOptional Cam Lock
(Ref No. 11)(Ref No. 11)
DividerDivider
(Ref No.10)(Ref No.10)


NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
49B12949B129