TOORX WBX-2400 User manual

Ed : Rev : Cod :
INSTRUCTION
06/18 GRLDTOORXWBX240000

- 4 -
Training Area and Free Area
Free Area
Training
Area
Specifications
Class：S
Maximum Wt. Capacity：100kg/220IBS
Maximum User Weight：135kg/297IBS
Product Total Surface：1027*706mm
Product Total Mass：50kg/110IBS

- 5 -
REGULAR MAINTENANCE
1．The safety level of the equipment can be maintained only if it is examined
regularly for damage and wear, e.g. ropes, pulleys, connection points;
2．Pay special attention to components most susceptible to wear.
3．Replace defective components immediately and /or keep t he equipment out of
use until repair;
4．This equipment should carry on regular maintenance according to the following
chart:
INSTALL SKETCH MAP
Let assembly become easier
All the content of user’s manual is to assured the strength training machine can be
installed more easily
Reading the details and instructions before installing:
1．Because the size and weight of equipment is so large, Please choose the installed place
near the desired station and assured there is enough space to exercise
2．All parts can be put on the clear area, then backout the wrapper. And the wrapper can’t
be through away before installation finished.
3．Screw the bolt tightly except the additional instruction
4．All parts must be installed according the illustration indication.
5．Installation work can be finished by tow men
6．Identify all parts by part identify chart
MAINTENANCE
EVERYDAY
EVERY WEEK
THREE MONTHS
Check: connecting, bolt,
Weight stack bolt
√
Clearance:
cushion and cover
√
Lubrication:
place of sliding
√
Check:
bolt if tighten
√
Lubrication:
Bracket of bearing
√

- 6 -
Exploded picture

- 7 -
Assembly Step：
Use tool：
1. M6 Hex spanner
2. M6 Hex spanner
3. Two 17-19 spanner

- 8 -
NO. Mame Size Quan tity
AC1 main frame
welding group 1 1
AC2 1 C09 C10
gas spring
flat gasket
1
8
∮13.5*∮24*2.5t
C07 outer hexagon
screw M12*1.75P-80L 2
45kg
C13
C84
M03
lock nut M12*1.75P 4
outer hexagon
screw M12*75牙长40 2
flat oval pads ∮80*135 3
Step1 main frame
welding group 2
C09
2-C10
2-C07
AC1
2-C10
2-C13
AC2
2-C10
2-C84
M03
M03
M03
2-M02
AC2
2-C10
2-C13
AG1
G09

- 9 -
No. Name Size Quantity
AG1 base plate
welding group 1
J04 upholstery 1
C15 C16
Screw cut hexagon
flat gasket
10 10
∮9*∮16*1.6t
J08
A1
upholstery D3 1
M8*1.25P-25L
C66 jacking screws M6*1.0P-15L 3
Step2
J08
C09
2-C10
2-C07
AC1
2-C10
2-C13
AC2
2-C10
2-C84
M03
M03
M03
2-M02
AC2
J04
4-C16
4-C15
4-C15
4-C16
2-C10
2-C13
AG1
G09

- 10 -
Adjust Instructions
Seat Height Adjustment
1、Pull out the adjustable handle,adjust seat cushion to suitable position,and
loosen the handle.
2、After finish adjusting,please ensure that the bolt of the adjustable handle
is inserted to pin hole completely before using the equipment.

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]