TOORX BRX R300 ERGO User manual

Ed : Rev : Cod :
INSTRUCTION
02/20 GRLDTOORXBRXR300R00
iConsole App Manual
www.toorx.it/iconsole

4
Pre-assembly Notes
Open the boxes:
Make sure to inventory all the parts that are included in the box. Check the hardware chart
of a full count of the number of parts included for proper assembly . If any of the parts are
missing, contact with the dealer.
36 Φ10-4
29 M4×16-4
26 M10×70×20-4
25 M12×60-2
94 M6×15-2
23 M6×35-8
24 M8×40×20-2
96 Φ10-4
42 M8-2
31 ST4×12-4
R30
93 M8×30-2
34 Φ8-2

5
GATHER YOUR TOOLS
Before starting the assembly of your unit，gather the necessary tools. Having all of the
equipment at hand will save time and make the assembly quick and hassle-free.
CLEAR YOUR WORK AREA
Make sure that you have cleared away a large enough space to properly assemble the
unit. Make sure the space is free from anything that may cause injury during assembly.
After the unit is fully assembled, make sure there is a comfortable amount of free area
around the unit for unobstructed operation.
NOTE: Each step number in the assembly instructions tells you what you will be doing.
Read and understand all instructions thoroughly before assembling the treadmill.
Product instruction
NO.
NAME
SPECIFICATION
QUANTITTY
23
Allen C.K.S full thread screw
M6×35
8
24
Allen C.K.S half thread screw
M8×40×20
2
25
Allen flat end set bolt
M12×60
2
26
Allen C.K.S. half thread screw
M10×70×20
4
29
Phillips pan head full thread screw
M4×16
4
31
Phillips C.K.S. self-tapping screw
ST4×12
4
34
Flat washer
Φ8
2
36
Spring washer
Φ10
4
42
Hex locking nut
M8
2
93
Allen C.K.S. full thread screw
M8x30
2
94
Allen cylinder head full thread
screw
M6×15
2
96
Flat washer
Φ10
4
L-shaped wrench
5×80×80S
1
L-shaped wrench
6×66×144
1
Open-end wrench
t4.0×28×130
1
Motor belt

6
Technical information
*WE RESERVE THE RIGHT TO AMEND THE PRODUCT WITHOUT PRIOR NOTICE.
DIMENSION
Unfold：1545x650x1140mm
SPEED RATIO
10.3
FLYWHEEL
single-track EMS flywheel, Φ215.4/8kg
Handlebar
Console
Front stabilizer
Rear stabilizer
Upright post
Saddle
Pedal - R
Pedal - L
Back cushion

7
Step 1: Attach the front stabilizer (2) to the main frame (1) with spring washer(36) ,flat
washer(96)and Allen C.K.S. half thread screw(26).
Step 2: Attach the rear stabilizer (3) to the main frame (1) with spring washer(36), flat
washer(96) and Allen C.K.S. half thread screw(26).
ASSEMBLY INSTRUCTIONS
26
26
36
36
2
1
96
96
26
36 26
36
3
1
96
96

8
Step 3:
1. Connect motor communication wire (82) with upright post communication wire(83).
2. First remove the plug from the upright post. Attach upper upright post (4) to main
frame (1) with Allen flat end set bolt (25). Then cover it with hold plug. Please lock the
two Allen flat end set bolts at the same time,and fix the screws by turns.
Step 4:
1.Connect the console communication wire (83) with back hole of console. Connect
handle pulse connection wire (86) with console outlet .
2. Attach the console (81) to upright post (4) with Phillips C.K.S. full thread screw (32).
4
25
76
83
82
1
32
81
83
86
4

9
Step 5:
1. Attach the handlebar cover - left (54) and right (55) to upper upright post (4) with
Phillips pan head full thread screw (29).
Step 6:
1. Fixed the handlebar post. Through T shape knob (65) out of handlebar. Rotate inside.
Adjust the handlebar tube to the suitable position. Rotate T shape knob tightly. Then
lock the handlebar front cover (56) with Phillips C.K.S. self-tapping screw(31).
56
65
31
31
5
4
29
29
54
55
4

10
Step 7:
1. Attach the pedal –left (63) and right (64) to the main frame (1).
Step 8:
1. Attach the brake adjustment round bar (8) to saddle base with Allen C.K.S full thread
screw (94).
2. Attach the back cushion tube to saddle base with Allen C.K.S. full thread screw (93)
64
63
1

11
Step 9:
1. Attach the saddle (60) to saddle base with Allen C.K.S. full thread screw
(23).
Step 10:
1 . Attach the handle pulse tube(6) to saddle，and lock with Allen C.K.S. half thread screw
(24), Hex nut (42) and flat washer(34).
2 . Connect the handle pulse connection wire (87) and (88). As shown below picture.
60
23
24
4234 24
4234
88
87
6

12
Step 11:
1 . Attach back cushion (61) to the back cushion tube (11) with Allen C.K.S full thread
screw(23)
Step 12:
1 . Insert the power pugs into power hole as shown below. Assembling finished
Workout tips:
1,User need to put the feet completely inside the pedal, and to adjust the resistance of
magnet control according to user.
2,Since the machine with double flywheels and it will have huge moment of inertia, when
23
61
11