TRONXY X5SA-400-PRO User manual

Thank you for choosing TRONXY products!
We will serve you whole heartedly!
Please read the instruction carefully
Please visit tronxy.cn for more information
After- sale service：[e-mail]
TEL：[phone]
Relevant information is stored in
SD card,please check

Pay attention
Please read this instruction carefully and follow the
safety instruction.
When the 3D printer is working, it will produce high temperature.Do not
touch working parts or extruder directly.After printing, the working part
may still be in the high temperature state.Please wait patiently for the
working parts and the print model to cool down before removing the model
from the print platform.
Please use the 3D printer in a spacious and well-ventilated
environment.
The recommended ambient temperature for 3D printers is 8°
c-40 °C, and the humidity is 20%-80%. Using outside this
range may bring bad printing effects.
In case of emergency, could turn off the power of the
3D printer directly.
3D printers contain working parts that move at high speeds,
so be wary of pinching your hands.
When removing the model from the print platform, be careful
not to swipe sharp objects at your finger.
Assemble the 3D printer or polish the model. suggest Wear
goggles.
Please pay attention to the protection of 3D printer
against rain and moisture.
Keep children away from the machine when it running
It is not recommended to run a 3D printer when left
unattended.

Catalogue
1. Machine parameter ………………………………………1
2. Introduction to machine structure …………………2
3. Packing list ……………………………………………………3
4. Installation instructions …………………………………4
5. Interface operation and printing …………………17
6. Slice software ………………………………………………20
7. Fault cause analysis ………………………………………23

Print parameters
Print principle: FDM (Fused deposition molding)
Print size: 400× 400×400 (mm3)
Print accuracy: 0.1-0.4 mm
Positioning accuracy: X/Y 0.0125mm，Z 0.0025mm
Nozzle quantity: 1
Nozzle size: 0.4 mm
Print speed: 20~100mm/s (suggest 60mm/s)
Moving speed: 100mm/s
Filament: PLA, TPU, ABS, wood, pc,HIPS, wooden filament etc.
Temperature parameters
Environmental temp: 8℃ - 40℃
Nozzle temp: Max260℃
Heat bed temp: support
Software
Slice software: Cura
Input format: .STL .OBJ
Output format: GCode
Connection: TF card, USB cable(Suitable for skilled users)
Power supply
Power input: 110V/220V AC, 50/60Hz
Power output： 24V/15A DC
Physical parameter
Machine size: 660mm×660mm×680mm
Machine weight: ~15.5kg
1. Machine parameter
1

2
2. Introduction to machine structure
④
⑤
①
②
③
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑮
⑭
⑰
1.Touch screen 2.Z1motor 3.Heatbed 4.Y axis switch
5.Y-right guide rail 6.Y-right sliding parts 7.Xmotor
9.Ymotor 10. Yleft sliding parts 11. Y-left guide rail
13.polish rod
12.lead screw
14.Z2motor 16.TF interface
17.USB interface 18.PIN line interface 19.power switch 20.power supply
15.aluminum frame
㉑㉒
21.switch lines box 23.filament run-out detection
22.Titan extruder
8.extruder head
㉓
⑯⑱⑲
⑳
controller box

3. Packing list
2040aluminum
profiles 530mm
4pcs
2020aluminum
profiles
600mm4pcs
530mm2pcs
OSG External double
axis guide rail
-Y axis 530mm 2pcs
OSG External double
axis guide rail
-X axis 550mm 1pcs
polished rod
528MM 4pcs
lead screws
453MM 2pcs
beams/footlock
2pcs
left and right
sliding parts
print head
left /right belt pulley
parts
X/Y axis motors
Zaxis motor
parts
Titan extruder
component bag
1pcs
controller & touch
screen
belt bag
filament
（Color random）
power line
seal
（Color random）
aluminum plate with
balck sticker
heat bed
screws bag
4pcs
shovel
（Color random）
USB cable
Tools bag
reader+TFcard
YZswitch parts
1pcs
filament run out
detection parts
1pcs
drag chain parts
1pcs
3
After receiving the goods, please
check the accessories according to
the packing list. If you have any
questions, please contact customer
service.

4. Installation instructions
Step 1：base frame assembly
Assembly material specification and quantity：
aluminum 1
20*20*600 4pcs
aluminum 2
20*20*530 2pcs
aluminum 3
20*40*530 4pcs
foot pad Φ20*12
4pcs
screws RM4*8
4pcs
gasket M4
4pcs
boat nuts M4
4pcs
scews RM5*25
12pcs
Assembly tips for M4 ship nut: first align the M4
nut with the aluminum profile slot, put it into the
aluminum profile slot, use a screwdriver to reverse
loosen, release the M4 ship nut over the aluminum
profile slot, and then tighten it forward.
2-aluminum 1
2-aluminum 2
4-aluminum 3
8-M5*25
aluminum 1
20mm
Note: do not lock the screw to facilitate subsequent
adjustment.
2-aluminum 1
4-M5*25
4
4-M4*8
4-gasket M4
4-gasket M4
4-boat nuts

Assembly material specification and quantity：
base frame
1pcs
Y axis guide rail
20*20*530 2pcs
left sliding parts
1pcs
right sliding
parts 1pcs
screws RM5*25
4pcs
Step 2: Sliding plate assembly
1.Take out the Y axis guide rail and put
it into the left and right sliding parts
respectively, as shown in the figure.
2.Note the direction of the slide. The
front of the slide should be on the
same side as the counterbore of the
guide, as shown in the figure.
Pay attention the direction of the
counterbore
Screw RM5*25 do not lock tight the Y axis guide rail,
which is convenient for subsequent adjustment
left sliding parts
right sliding parts
4-M5*25
5

Assembly material specification and quantity：
basic frame 1pcs
X axis guide
rail parts
20*18*550 1pcs
Print head parts
1pcs
drag chain
plate
1pcs
screws RM4*20
4pcs
Step 3：Print head assembly
As shown in the figure, the pulley on the print
head runs through the X axis guide rail and
the slide block moves smoothly without any
clearance
pulley
M4 screws holes positioning
print head
2-M4*20
2-M4*20
60mm
105mm
X axis guide rail
1.Insert the print head into the X-axis guide rail, pay attention to the direction of the M4 screw hole, as
shown in Figure 1.
2. Insert the X-axis rail assembly into the alignment hole of the chassis, and tighten the screw
RM4*20 without locking it, as shown in Figure 2.
3. Move the left and right sliders to confirm that the X-axis rail assembly moves flexibly after locking
the RM4*20 screw.
4. After adjustment, lock the screw of RM5*25 on the Y-axis guide and move the X-axis guide assembly
again. Repeat the adjustment to ensure that the slide is flexible and has no gap after the locking screw.
The skateboard is in line with
the X-axis guide
6

Assembly material specification and quantity：
basic frame parts
1pcs
right wheel parts
1pcs
left wheel parts
1pcs
X motor
1pcs
Y motor
1pcs
Step 4：XY axis motors and wheels assembly
1. Lock and fix the assembled parts in the
position as shown in the figure
Assembly tips for M4 ship nut: first
align the M4 nut with the aluminum
profile slot, put it into the aluminum
profile slot, use a screwdriver to
reverse loosen, release the M4 ship
nut over the aluminum profile slot,
and then tighten it forward
7
This screw
positioning
Don't need to
tighten
This screw
positioning
Don't need
to tighten

Assembly material specification and quantity：
basic frame
1pcs
Belt
2pcs
Ties
Step 5：Belts assembly
4-M3*3
8
Synchronous wheel
Synchronous wheel
Note: When the machine prints normally
after assembly.If the belt is too loud when
moving,The height of the left and right
wheel assembly can be adjusted by
increasing and reducing the gaskets.
During the printing process, the leather belt
has a slight sound, which is normal.
Left and right wheels
Belt tying diagram
X motor
Y motor
1.As shown in the figure, after
adjusting the distance between
the motor gear and the belt, lock
the 2 rice screws on the gear.
2. Also assemble the second belt,
the tension of the second belt
should be equal.
Note: Synchronization wheels on X, Y axis motors
Height should be adjusted by itself.
Be sure to install the belt
Each belt is on the same planeUp.
Location of Print Head Band

Assembly material specification and quantity：
beams
2pcs
Linear bearing
4pcs
copper linear
bearing
2pcs
screws RM3*12
24pcs
Step 6：Linear bearing assembly
12-M3*12
9

Assembly material specification and quantity：
basic frame
1pcs
Z axis motor parts
2pcs
foot lock parts
2pcs
bearing base parts
2pcs
polish rod
Φ8*528
4pcs
lead screwT8*453
2pcs
screws RM4*20
8pcs
screws RM4*8
4pcs
Shimφ12*φ4*1
8个
Step 7：Z axis parts assembly
10
polish rod
polish rod
lead screw
bearing base parts
Adjust the verticality of the polished
rod and tighten the screws
4-M4*8
4-M4*20
Shim
2-M3*3
4-M4*4
As shown in Figure 1, assemble the assembly, put
the assembly into the frame as shown in Figure 2,
and align the holes to lock the screws.
Shim
M3 hole is inside.

Assembly material specification and quantity：
basic frame
1pcs
Z axis motor parts
2pcs
L angle code
1pcs
screws RM4*6
2pcs
boat nuts M4
1pcs
Step 8：Controller box assembly
Separate the screen from the host and
Fix the M4 boat nut on the bottom rack as shown
2-boat nuts
2-M4*6
boat nuts
2-M4*6
boat nuts
11
Fix the boat nut on the main box to the
bottom shelf with the locking L corner
code, as shown in the figure

Assembly material specification and quantity：
basic frame
1pcs
heat bed parts
1pcs
beams
2pcs
plastic nuts M3
6pcs
screws RM3*16
2pcs
spring
6pcs
nuts M3
6pcs
screws KM3*30
6pcs
screws RM4*12
8pcs
drag chain parts
1pcs
Step 9：Print plate assembly
4pcs hole position
6-KM3*30
6-spring
6-M3 nuts
10mm
2-M3*16
8-M4*12
2-boat nuts
2-M4*8
2-M3*6
fixed drag
chain
beams
12
Place the left and right horizontal plates on the same
plane, and lock the hot bed assembly on the horizontal
plate according to Figure 3. Fix the towline bracket
according to Figure 4.
Adjust the hot bed to the left and right level, move up
and down smoothly, then tighten the screws

Assembly material specification and quantity：
basic frame
1pcs
filament run out
detection parts
1pcs
Titan extruder
1pcs
screw RM4*6
4pcs
boat nuts M4
2pcs
screw RM4*6
2pcs
Step 10：Feeding motor assembly
2-RM4*6 2-boat nuts
13
RM4*8
RM4*8
10MM
Assemble Titan extruder to filament runout detection parts
As shown, lock the Titan extruder assembly to the basic frame

Assembly material specification and quantity：
printer
1pcs
YZ switch parts
1pcs
bracket part
1pcs
screw
RM5*12
screw
RM4*6
4pcs
boat nuts M4
4pcs
Step 11：Switch and filament bracket assembly
feeding tube
Note: the feed tube of the print head is not inserted at the bottom, which
may lead to blockage.
2-RM4*6 2-boat nuts M4
YZ switch parts
2-RM4*6 2-boat nuts M4
2-M5*12
14

Assembly material specification and quantity：
printer
1pcs
seal
end cap
8pcs
clips
Step 12：Black sticker and seal assembly
4-clips seal 8-end cap
15