TRONXY X6D User manual

M3 nuts 60pcs M3*20mm screws
58pcs
M2*8mm black screws
2pcs
M3*10mm screws
17pcs
M8 nuts 12pcs
M8 Cushion ring
12pcs Plastic Pillars 4pcs
M3*14mm screws
4pcs
M3*30mm screws
7pcs
Classification Of Screws

M4*15mm screws
12pcs
Compression springs*4
Wing nuts*4
Classification Of Screws
M3*30mm screws 4pcs
M3*20mm screws
4pcs
M2*18mm screws&nuts
4pcs

Step 1 Assemble Y-axis Motor
M3*10mm
screws*4
Y-axis motor
support
Y-axis motor
M3*2mm jackscrew
GT2-16 pulley
Fit the GT2-16 pulley on the motor, Locking with M3*2mm
jackscrew.
As the picture, Put Y-axis motor on <Y-axis motor support> ,
locking with Four M3*10mm screws.

Step 2 Assemble Y-axis Limit switch
Put the Y-axis limit switch and the holder together ,locking
with two M2*18mm screws & nuts. As picture M2*18mm screws
Y-axis limit switch
Y-axis limit
switch holder
(Acrylic)
M2 nuts

Step 3 Assemble Base Frame Holder_Back
Y-axis motor
assembly
Sliding rod
Restriction*2
M3*20mm
screws
Y-axis limit
switch assembly
Y-axis motor
holder
Base frame
holder_Back
M3 nuts
As the picture, put two of the Sliding rod
Restriction in front of the base frame
holder (back). locking with two
M3*20mm screws & nuts.
Put the limit switch and holder assembly
on the base frame holder, locking with
one M3*20mm screw & nut.
Put Y-axis motor holder on base frame
holder ,locking with one M3*20mm
screw & nut.
Put Y-axis motor assembly on base
frame holder, locking with three
M3*20mm screws & nuts.

Step 4 Assemble Base Frame Holder_Front
Sliding rod
Restriction*2
M3*20mm Screws
& nuts
Y-axis belt pulley
wheel assembly
Base Frame
Holder_Front
As the picture, put two of the Sliding rod
Restriction in front of the base frame holder
_front. locking with two M3*20mm Round head
screws & nuts.
Put Y-axis belt pulley wheel assembly behind
the base frame holder, Locking with two
M3*20mm screws & nuts.

Bearing
Fan duct
Turbo Fan
M3*16mm
screws
Step 5 Assemble Extruder
Cooler Fan
Metal Block
M3*16mm
screws
Install 3pcs Bearings to the U-Metal Plate,
Locking with 12pcs M4*8mm screws.
Put Motor& Hotend module and U-Metal plate
together , locking with 2pcs M3*10mm screws .
Put Turbo Fan and Fan duct to the U-Metal plate,
and locking with 2pcs M3*16mm screws
Place Cooler Fan on the Metal Block use 2pcs
M3*16mm screws .
Place X-axis limit switch to the U-Metal plate
using M2*8mm screws
U-Metal plate
Motor &
Hotend
X-axis limit
swith
M2*8mm
screws

Step 6 Assemble Z-axis motor
coupling
M3*20mm screws
M3*10mm screws
Z-axis motor
support(side)
Z-axis motor
support(top)
Z-axis motor
Put two Z-axis motor support(side) in two
sides of the motor, Cover the Z-axis motor
support(top) on the top, locking with
M3*20mm screws & nuts.
The cable of Z-axis motor is back of the Z-axis
motor support. Locking Z-axis motor with
four M3*10mm screws.
Put the coupling on the motor, locking with
the jackscrews.
Another Z-axis motor is the same assembly.
Note: There are 2pcs Z axis motors . See the
hole , the right motor put the hole on the
right , the left motor put the hole on the
left . (The picture shows the right motor )

Step 7 Assemble Side plate
As the picture, Put the two Side plate on the
left and right side of the Framework, locking
with six M3*20mm screws & nuts.
Side plate
M3*20mm
screws
Framework

Step 8 Install Base frame holder_Back
Base frame
holder_back
M3*20mm
screws*4
Put the Base frame holder_back back of Side plate,
locking with four M3*20mm screw

Z-axis motor assembly
Framework
M3 nuts
M3*20mm
screws
As the picture, Put the two Z-axis motors assembly
on the left and right side of the Framework,
locking with three M3*20mm screws & nuts.
Step 9 Assemble Z-axis
The hole is on the left
The hole is on the right

Step 10 Assemble Top plate & Junction Plate
Sliding rod
restriction
Junction Plate
Framework
M3*20mm
screws
Put the two Junction Plate on the top of the
Side plate ,locking with four M3*20 screws &
nuts.
Put two sliding rod restriction on the top of
left and right sides. Locking with one
M3*20mm screw & nut each.

Step 11 Install Base Frame Holder_Front
M8 cushion ring
M8*400mm
screw arbors
Base frame
holder_front
M8 nuts
Through the Frame Holder_Front & Back by two
M8*400mm screw arbors, locking with twelve
M8 Nuts & cushion ring.

Step 12 Assemble Bed frame
Place three bearings under the bed frame,
locking with twelve M4*15 screws.Bearing*3
M4*15mm
screws *12

Step 13 Assemble Bed frame
Through the bed frame on the base by two of M8*380mm
Sliding rod. Fix both end by Sliding rod restriction
Tighten one end of the timing belt to the bed frame using a
zip-ties. the other end through the Y-axis motor and belt
pulley wheel on the base frame holder , Then tighten it to
the bed frame using zip-ties as shown in the picture .
M8*380mm
sliding rod*2
Sliding rod
Restriction
Timing belt
Zip-ties

Sliding rod
restriction
M8*350mm
Sliding rod
Coupling
M8*315mm
screw arbor
X-axis Pulley
mount
X-axis Motor
mount
Step 14 Instal X-axis Motor & Pulley mount
Put X-axis motor on X-axis motor mount.
Locking with three M3*10mm screws.
Through the X-axis motor mount & pulley
mount by M8*350mm sliding rod &
M8*315mm screw arbor. As picture
Fix the top of sliding rod with sliding rod
restriction, connect the bottom of screw
arbors with couplings , locking jackscrew in
coupling.
X-axis Motor

Step 15 Assemble Heatbed
Place the MK3 heatbed on the bed frame use
4pcs springs between them, and then through
4pcs M3*30mm screws, top 4pcs wing nuts
under the bed frame.
MK3 Heatbed
M3*30mm
screws *4
Springs*4
Wing nut*4

Step 16 Assemble X-axis
X-axis motor
mount X-axis pulley
mount
M8*420mm
sliding rod Extruder
assembly
Through the X-axis motor mount &
Pulley mount and Extruder assembly
using two M8*420mm sliding rods, as the
picture.

Step 17 Instal X-axis Timing Belt
X-axis timing belt
Tighten one end of the Timing Belt to the
Belt hole with Zip-ties. The other end
through the X-axis pulley & motor , then
tighten another end of the belt to the Belt
hole with Zip-ties . as picture below
Belt Hole
Zip-ties