Tumbl Trak 5in1 User manual

Parts ListParts List
D
B
A
C
D
B
A
C
Parts List:
[A] Side Legs (qty 2)
[B] Kip Bar assembly (qty 2)
[C] Vercal Supports (qty 4)
[D] Center-Beam Support (qty 2)
[E] Buon-Head Cap Screws (qty 8)
[F] Lock Washers (qty 8)
[G] Flat Washers (qty 8)
[H] 6mm Allen Wrench (qty 1)
[I] D-2 Spring-Detent Knobs (qty 4)
F
H
E
G
I
Thank you for purchasing the
5-in-1 Bar. You will enjoy years of
use with this product.
Aer opening the boxes, please
check the parts list to make sure all
pieces have arrived in good
condion.
If you have any quesons during
this assembly process, please call
customer service at
1-800-331-4362.
J
5-in-1 Assembly Instructions
For quesons or problems, please call Tumbl Trak at
[phone]

NOTE: Tumbl Trak equipment is not recommended for
the use in Parkour/Free Running related activities.
Step 1- Place the screw through the lock
washer and then the at washer. Repeat for
Step 2- Align the one of the uprights with the center
support. Align the second upright with the center
support. NOTE: Make sure D-2 knob holes are facing
Step 3- Place two of the screw and washer sets
into the upright and center support on each
end. Tighten these by hand. NOTE: It will be
Step 5- Place the downtubes of the bar assembly into
the uprights. You may have to adjust the
uprights to allow the downtubes to slide in. If it is sll
dicult spray some WD-40 on the downtubes. Repeat
Step 4- Repeat Steps 2 & 3 for
the second set of uprights and
center support.
Step 6- Once the bar assembly is seated all the
way in the upright, nish ghtening the
screws in the center support. Repeat for sec-
Step 7- Place the D-2 knobs
in all four uprights.
Step 8- Adjust the bars to your desired height
and ghten the D-2 knobs. Ensure you see
and hear the knob lock. NOTE: You should
not be able to move the bar assembly if it is
properly locked with the D-2 knobs.
Step 1
Step 2
Step 3
Step 5
Step 6
Step 6
Step 6
For quesons or problems, please call Tumbl Trak at
[phone]

General Guidelines
(125 lb. limit)
NOTE: Tumbl Trak equipment is not recommended for
the use in Parkour/Free Running related activities.
Step 9- Li and push the knob against
the upright then place the unit on the
side leg. Release the knob and allow the
boom lip to t securely under the side
leg. Repeat for the other side of the
upright & bar assembly. NOTE: You may
have to unscrew the knob slightly to
allow clearance.
Step 10- Tighten the knob to secure the
boom lip under the side leg and the
upright in posion. Repeat for the other
side of the upright & bar
assembly.
ENJOY!
Step 11- Wrap the clamp pad around the
knob on the outside of the upright.
Velcro the small strip around the
upright and the large strip below the
clamp. Repeat for the other side of the
upright & bar assembly.
Step 9 Step 9
Step 10
Step 10
Step 11
For quesons or problems, please call Tumbl Trak at
[phone]

The following accessories can be purchased from Tumbl Trak’s website at www.tumbltrak.com or by calling 1
-800-331-4362.
Cast Trainer (*shown on Jr Bar Pro)
 Add it to the 5-in-1 Bar and have three bars to use
 Easily attaches to the 5-in-1 Bar
Bar Pad
 Developed for the smaller athlete
 Easily attaches to bar with Velcro
 Measures 9.5” wide and 1.5” in diameter
4’x8’x8” Mat
 Provides soft base under the 5-in-1 Bar
 May be used for tumbling skills when not in use with
the 5-in-1 Bar
 Folds in 1/2 and has handles for ease of transport
 Non-skid material on the bottom prevents sliding
Power Launch
 Provides a bouncy surface under the 5-in-1 Bar
 Attach it to the side of the unit for a handstand station
 Use it behind the bar for a clear hip wall
 Add the carpet wall overlay as a handstand Trainer
Scan the QR Code with your smartphone to
learn more about what you can do with your
new Tumbl Trak product!
Accessories for the 5Accessories for the 5- -inin- -1 Bar1 Bar
For quesons or problems, please call Tumbl Trak at
[phone]