Tyco 4100ES User manual

SP1 Fire Indicator Panel
Operator’s Manual
4100ES Fire Indicator Panel
Operator’s Manual
LT0568 Iss 1.0
InfoAlarm Operator’s Manual

4100ES Fire Indicator Panel Operator’s Guide
Fire detectors in the building are grouped into zones (searchable areas).
Zones can be Isolated by pressing the zone’s isolate pushbutton on the panel – this prevents an
alarm from activating the panel outputs.
When a non-isolated detector detects an alarm, the fire panel displays the alarm information, calls
the fire brigade, activates the Warning or Evacuation System (EWS), and initiates any other
programmed functions.
The fire panel display consists of two sections –the operator interface (upper section) and the Zone
Isolate pushbutton switches & indicators (lower section).
The operator interface indicates common Alarm, Fault & Isolation Status on LEDs, and point
(detector) status on the LCD.
When an Alarm, Fault or Isolation occurs, the buzzer will operate until the corresponding
acknowledge (Ack) key is pressed.
Silence the External Bell or Strobe: Press the
<EXT BELL ISOLATE> key.
Silence the Evacuation System: Press the
<WARN SYS ISOLATE> key. This will turn off warning
sounders powered by the Fire Panel.
Isolate a Zone: Press the appropriate Zone Isolate
pushbutton and the Isolated LED for that zone will turn on.
Acknowledge an Isolation: Press the <ISOLATE ACK>
key.
Acknowledge an Alarm: Press the <FIRE ALARM ACK>
key.
Acknowledge a Fault: Press the <FAULT ACK> key.
The panel is reset by pressing <SYSTEM RESET>. If an alarm won’t reset, the point may still be
activated. Press <FIRE ALARM ACK> when the point alarm is displayed, then press <DISABLE>,
<ENTER>. Press <FAULT ACK> (to acknowledge the fault caused by disabling a point), then press
<SYSTEM RESET> again. The disabled detector must be re-enabled when the condition is cleared.
Operator Interface
Zone Isolate
Pushbuttons

iv
Australian Standard AS 4428.1, Control and Indicating Equipment. ActivFire Listing No. afp1682
The 4100ES is manufactured for :
Tyco Fire Protection Products
47 Gilby Road
Mt Waverley
VIC 3149
AUSTRALIA
Phone : [phone]
Fax : [phone]
2013 Tyco Australia Pty Limited. All Rights Reserved.
All specifications and other information shown were current as of document revision date, and are
subject to change without notice.
Tyco, Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, WALKTEST,
MINIPLEX, and TrueAlert are trademarks of Tyco International Services AG or its affiliates in the U.S.
and/or other countries. VESDA is a trademark of Xtralis Pty Ltd.
Simplex fire alarm technology is protected by the following U.S. Patent Numbers:
TrueAlarm analog smoke detection: 5,155,468; 5,173,683 and 5,543,777. IDNet and
MAPNET II addressable communications; 4,796,025. TrueAlert addressable notification;
6,313,744 and 6,426,697. SmartSync horn/strobe control; 6,281,789.
No part of this document may be reproduced or transmitted in any form or by any means, electronic
or mechanical, for any purpose, without the express written consent of Tyco Fire Protection Products.
Document Number : LT0568
Issue : Issue 1.0, 1 October 2013
1.03.05
Manufacturer’s Details
Approvals
Manufacturer
Copyright and
Trademark
Information
Document
Firmware
Revision
Amendments

v
4100ES Panel Supplied by:
Installation Location
Contract/Job Number
As installed, FIP System Drawing Number
Panel Installation Date
Panel Commissioned Date
Weekly Battery Test Day & Time
Maintenance Company
Telephone
Service Contract
Some of the operation of the 4100ES, as described in this manual, is dependent on custom
configuration as performed by the field engineer. If the configuration is not as per the
recommended template, then the operation may differ and compliance to AS 4428.1 may
be invalid.
The 4100ES has a facility to allow levels of passcode protection. The standard
programming template has operation of all the functions as described in this manual set to
not require entry of a passcode.
ZONE ISOLATIONS - The zone isolate status is not stored in non-volatile memory, so if
the panel is powered down and back up, or restarted in any way, all zones will be de-
isolated.
CLASS A PRODUCT –In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Product/Site
Cautions &
Warnings

vi
Approvals....................................................................................................................iv
Manufacturer...............................................................................................................iv
Copyright and Trademark Information........................................................................iv
Document ...................................................................................................................iv
Firmware Revision......................................................................................................iv
Amendments...............................................................................................................iv
Product/Site.................................................................................................................v
Cautions & Warnings...................................................................................................v
Chapter 1 Overview.........................................................................1-1
Introduction...............................................................................................................1-1
In this Chapter ..........................................................................................................1-1
Typical Panel Layout..............................................................................................1-2
Overview...................................................................................................................1-2
Basic System Description......................................................................................1-3
Overview...................................................................................................................1-3
Control Keys & Indicators......................................................................................1-5
Overview...................................................................................................................1-5
Control Keys & Indicator Functions..........................................................................1-5
Normal Appearance of Operator Interface...........................................................1-6
Description................................................................................................................1-6
Chapter 2 Managing Alarm Conditions .........................................2-1
Introduction...............................................................................................................2-1
In this Chapter ..........................................................................................................2-1
Acknowledging Alarms..........................................................................................2-2
What the System Does When an Alarm Occurs ......................................................2-2
Overview –Acknowledging Alarms..........................................................................2-2
Procedure.................................................................................................................2-3
Isolating (Silencing) the Warning System or External Bell ................................2-4
Overview...................................................................................................................2-4
Isolating the EWS.....................................................................................................2-4
Isolating the External Bell.........................................................................................2-4
Isolating the Zone.....................................................................................................2-4
Isolating ACF Outputs............................................................................................2-5
Overview...................................................................................................................2-5
Operation..................................................................................................................2-5
Restoration ...............................................................................................................2-5
Resetting Alarms ....................................................................................................2-6
Overview...................................................................................................................2-6
Reset Procedure.......................................................................................................2-6
Resetting Air Conditioning Controls ....................................................................2-7
Overview...................................................................................................................2-7
Indication ..................................................................................................................2-7
Resetting...................................................................................................................2-7
Displaying Event Time ...........................................................................................2-8
Procedure.................................................................................................................2-8
Chapter 3 Managing Fault and Isolate Conditions.......................3-1
Introduction...............................................................................................................3-1
In this Chapter ..........................................................................................................3-1
Acknowledging Fault or Isolate Conditions.........................................................3-2
How the 4100ES Indicates the Presence of a Fault or Isolate condition .................3-2
What Acknowledge Does .........................................................................................3-2
Panel Operating Procedure –Fault Condition..........................................................3-3
Resetting Fault Conditions .......................................................................................3-3
Viewing Fault or Isolate Conditions......................................................................3-4
Overview...................................................................................................................3-4
Chapter 4 Selecting Points for Status or Control.........................4-1
Introduction...............................................................................................................4-1
Selecting Points with the Function/Numeric Keypad .........................................4-2
Table of Contents

vii
Overview...................................................................................................................4-2
Selecting Points directly ...........................................................................................4-2
Chapter 5 Testing and Controlling Points.....................................5-1
Introduction...............................................................................................................5-1
In this Chapter ..........................................................................................................5-1
Alarm and Fault Test for Zones.............................................................................5-2
Alarm Test ................................................................................................................5-2
Fault Test..................................................................................................................5-2
Isolating and De-isolating Zones ..........................................................................5-3
Overview...................................................................................................................5-3
Isolating a Zone........................................................................................................5-3
De-Isolating a Zone ..................................................................................................5-3
Disabling and Enabling Points..............................................................................5-4
Disabling and Enabling Points..............................................................................5-4
Overview...................................................................................................................5-4
Disabling a Point.......................................................................................................5-4
Enabling a Point........................................................................................................5-5
Turning a Point ON or OFF....................................................................................5-6
Overview...................................................................................................................5-6
Turning a Point ON...................................................................................................5-6
Turning a Point OFF.................................................................................................5-7
Returning a Point to Automatic Operation................................................................5-7
Sounder (Buzzer)......................................................................................................5-7
Chapter 6 Displaying and Modifying Detailed Point Attributes..6-1
Introduction...............................................................................................................6-1
In this Chapter ..........................................................................................................6-1
Detailed Point Attributes........................................................................................6-2
Select a Point............................................................................................................6-2
See the Attributes.....................................................................................................6-2
Summary of Display-Only Attributes.........................................................................6-2
Example of Display-Only Attributes..........................................................................6-4
Chapter 7 Setting Access Levels and Logging In ........................7-1
Introduction...............................................................................................................7-1
In this Chapter ..........................................................................................................7-1
Logging In and Out of the System ........................................................................7-2
Introduction...............................................................................................................7-2
Log In Procedure......................................................................................................7-2
Log Out Procedure ...................................................................................................7-3
Chapter 8 Viewing and Clearing Historical Logs..........................8-1
Introduction...............................................................................................................8-1
In this Chapter ..........................................................................................................8-1
Viewing and Clearing the Historical Alarm and Fault Logs ...............................8-2
Viewing Logs ............................................................................................................8-2
Clearing the Logs......................................................................................................8-3
Chapter 9 Service-Related Operations..........................................9-1
Introduction...............................................................................................................9-1
In this Chapter ..........................................................................................................9-1
Setting Time and Date............................................................................................9-2
Procedure.................................................................................................................9-2
Displaying Software Revision ...............................................................................9-3
Procedure.................................................................................................................9-3
Displaying Software Revision, Continued ...........................................................9-4
Procedure (Cont’d) ...................................................................................................9-4
Viewing Card Status Information..........................................................................9-5
Overview...................................................................................................................9-5
Procedure.................................................................................................................9-5
Viewing Card Status Information, Continued ......................................................9-6
Power Supply/Charger Voltage and Current Readings............................................9-6
Displaying Network Node Information .................................................................9-7

viii
Overview...................................................................................................................9-7
Procedure.................................................................................................................9-7
Displaying Network Node Information, Continued .............................................9-8
Lamp Test................................................................................................................9-9
Procedure.................................................................................................................9-9
Warm Restart of the System................................................................................9-10
Overview.................................................................................................................9-10
Procedure...............................................................................................................9-10
Displaying IDNet & Mapnet Device Status .........................................................9-11
Introduction.............................................................................................................9-11
IDNet Display Information.......................................................................................9-11
IDNet Point Addressing ..........................................................................................9-11
How to Display an IDNet System Point..................................................................9-11
What To Do If an IDNet Point Will Not Reset.........................................................9-11
TrueAlarm Sensor Display Values..........................................................................9-11
Chapter 10 Walk Test Procedures ...............................................10-1
Introduction.............................................................................................................10-1
In this Chapter ........................................................................................................10-1
Walk Test™............................................................................................................10-2
Overview.................................................................................................................10-2
Zone Coding Option ...............................................................................................10-3
Silent Walk Test......................................................................................................10-3
Walk Test™Procedures........................................................................................10-4
How to Enter Walk Test Mode................................................................................10-4
How to Exit Walk Test Mode ..................................................................................10-6
Chapter 11 Printing Reports.........................................................11-1
Introduction.............................................................................................................11-1
In this Chapter ........................................................................................................11-1
Selecting Report ...................................................................................................11-2
Available Options....................................................................................................11-2
Printing a Report...................................................................................................11-3
Overview.................................................................................................................11-3
Procedure...............................................................................................................11-3
Chapter 12 Maintenance Procedures ..........................................12-1
Introduction.............................................................................................................12-1
In this Chapter ........................................................................................................12-1
AS 1851 Testing –Guide for 4100ES –Specific Test Methods............................12-1
Monthly Tests........................................................................................................12-2
Monthly Tests .........................................................................................................12-2
6 Monthly Tests ......................................................................................................12-2
Annual Tests .........................................................................................................12-3
Annual Tests...........................................................................................................12-3
Annual Tests - Smoke Hazard Management Systems...........................................12-4
Five Year Tests .....................................................................................................12-5
Five Yearly Tests....................................................................................................12-5
Battery and Keypad Test Details.........................................................................12-6
Battery Load Discharge Testing (AS 1851:2012 Item 3.7).....................................12-6
PSU Supervision (AS 1851:2012 Item 4.5)............................................................12-6
Panel Switches and Keypads (AS 1851:2012 Item 3.5).........................................12-6

1-1
This chapter provides an overview of the 4100ES operator interface and describes the normal
appearance of the operator interface.
Refer to the page number listed in this table for information on a specific topic.
Topic
See Page #
Typical Panel Layout
1-2
Basic System Description
1-3
Control Keys
1-5
Normal Appearance of Operator Interface
1-6
Chapter 1
Overview
Introduction
In this Chapter

1-2
The 4100ES is supplied with an InfoAlarm graphic Operator Interface plus one or more
Expansion Bays in a suitably sized cabinet. Refer to Figure 1-1.
The Zone Isolate modules are fitted into the Expansion bays from left to right. The first zone
is at the top of the leftmost module.
Depending on the size of the system and other functions required, Zone Isolate modules may
be fitted to the entire bay and additional Expansion Bays may have Zone Isolate modules
fitted. Small systems have only one Expansion Bay, and any required other modules are
installed to the right of the Zone Isolate modules.
Typical Panel Layout
Overview
Figure 1-1. Zone detail
Figure 1-1. Typical Panel Layout
Operator Interface
Alphanumeric display, Keypad,
Acknowledge & Control Keys.
Zone Isolate Modules
Red LED indicates alarm,
Yellow LED indicates isolation,
Pushbutton isolates & de-isolates
Ancillary
Controls
These are optional,
panel (site) specific
controls
Isolate
Pushbutton
Red Alarm
LED
Yellow
Isolate
LED