UFO LUNA SLP-3000M User manual

Luna Slimlin Plastic Light Sourc Rang
Mod ls cov r d by this manual:
UFO LUNA SLP-3000M
UFO LUNA SLP-4000M
UFO LUNA SLP-3000DMX
UFO LUNA SLP-4000DMX
UFO LUNA SLP-300010V
UFO LUNA SLP-400010V
Pl as r ad this manual fully b for installing, op rating or p rforming
maint nanc on th light sourc unit.
Light Source User Guide
Issue 4 | Revised: 310317
Universal Fibre Optics
Home Place | Coldstream | TD12 4DT | United Kingdom
Tel: [phone] | Fax: [phone]
www. ibreopticlighting.com

INTRODUCTION
Thank you or purchasing this UFO light source.
Please read these instructions ully be ore connecting your unit to the electrical
supply, and keep them or uture re erence.
The UFO Luna range o light sources are suitable or use with either glass or PMMA
ibre optic harnesses.
This luminaire is powered by a 24V Power Supply Unit or 24V constant voltage driver.
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE. WHEN THE LIGHT
SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
TYPE Y ATTACHMENT: I the external lexible cable or cord o this luminaire or
associated PSU/driver is damaged. It shall be exclusively replaced by the
manu acturer or his service agent or a similar quali ied person to avoid a hazard.
LOCATION: Do not locate this light source closer than 200mm rom any lammable
sur ace.
CLEARANCE/VENTILATION: It is imperative that a gap o 200mm is le around the
unit. This is to allow air to circulate and prevent overheating. The location must
have ree ventilation and must not have an ambient temperature higher than that
speci ied or the luminaire.
MOUNTING: This is a ixed luminaire. See separate mounting plate instruction on
Page 3 or ixing to sur ace.
WARNING: Never look directly into the Luminaire LED light source
Luna Light Source Range
2

INSTALLATION INSTRUCTIONS
POWER SUPPLY REQUIREMENTS
The LED light source is powered rom a 24V DC PSU/Constant Voltage SELV LED
driver. Remove the 24V PSU/driver rom its box. The driver caters or
UK/European/other mains supplies using the relevant power cord supplied.
Universal Fibre Optics 3
UFO LUNA SLP-M UFO LUNA SLP-DMX
UFO LUNA SLP-10V
Fit the metal mounting plate to the base o the Luminaire be ore making electrical
connections.
Remove the mounting plate and the our plastic 2 part (screw and rivet body) rom
the box. Invert the luminaire and remove the our rubber eet. Separate the screws
rom the rivet bodies and push it the rivet bodies into the holes vacated by the eet.
Align the plate against the rivets and secure the plate to the luminaire with the our
plastic screws using an M4 pozi-drive screwdriver. Do not overtighten. The luminaire
can now be ixed securely to the mounting sur ace.

CONNECTION – LUNA M
There are 2 connections required – the ibre port and the mains supply cable. The
ibre port should be connected irst. Connect and secure the ibre optic connector
into the collar and secure using the M5 locking screw.
Connect the PSU/driver to the DC input jack socket on the Luminaire. Plug the mains
plug into the electrical supply socket. Switch on power the led Indicator will
illuminate and the light source is ready or use. I no light is produced consult the
TROUBLESHOOTING section.
NOTE: THESE LIGHT SOURCES ARE NOT MAINS DIMMABLE
NORMAL OPERATION – LUNA M
Under normal operation the LUNA M light source can be dimmed manually using the
dimmer control on the rear o the unit.
Luna Light Source Range
4

CONNECTION – LUNA DMX
There are 3 connections required – the ibre port, the mains supply cable and the
DMX control cable. The ibre port should be connected irst. Connect and secure the
ibreoptic connector into the collar and secure using the M5 locking screw.
Connect the PSU/driver to the DC input jack socket on the Luminaire. Plug the mains
plug into the electrical supply socket. Switch on power the led Indicator will
illuminate and the light source is ready or use. I no light is produced consult the
TROUBLESHOOTING section.
NOTE: THESE LIGHT SOURCES ARE NOT MAINS DIMMABLE
Connect up the DMX control cables to the Mini-XLR sockets on the rear o the light
source. The recommended plug or these sockets is Multicomp SVP556-TA. The pin
out details or the plugs are shown below. Either socket may be used as DMX in or
DMX out.
Universal Fibre Optics 5
NOTE: CONVERTORS ARE AVAILABLE FROM UFO
Mini XLR to RJ45
Mini XLR to normal 3 pin XLR

DMX OPERATION
The DMX light siources can be dimmed remotely (single Channel 0-255 – SEE TABLE
BELOW) and can be addressed manually
Si gle Cha el Value 0 255
Description LED Off LED Brightest
Unless the address is speci ied on the Purchase Order, all light sources will be
de aulted to Address 001. Connect the DMX controller to either o the Mini XLR
sockets, and the light source can now be dimmed. Additional Slave (same address)
DMX light sources can be linked together.
To revert a DMX light source to non DMX control or manual operation:
1. Disconnect the light source rom the mains supply.
2. Tilt the light source on its side and remove the screw rom the base as shown below.
3. Slide the access cover down to remove and set the cover and screw aside.
4. Switch DIP switch 10 (top) to ON as shown below.
5. Replace access cover and securing screw.
Luna Light Source Range
6

SETTING THE DMX ADDRESS
1. Disconnect the light source rom the mains supply.
2. Tilt the light source on its side and remove the screw rom the base as shown below.
3. Slide the access cover down to remove and set the cover and screw aside.
4. Ensure DIP switch 10 (top) is set to OFF as shown below.
5. Set the address required as detailed in the address table, overlea.
6. Replace access cover and securing screw,
Universal Fibre Optics 7
Note: or DMX control operation to work, Dip switch 10 must be in the off position.

SETTING THE DMX ADDRESS
DMX B
START
Cha el #
DIP
Switches
O
DMX B
START
Cha el #
DIP
Switches
O
1 1 11 1,2,4
2 2 12 3,4
3 1,2 13 1,3,4
4 3 14 2,3,4
5 1,3 15 1,2,3,4
6 2,3 16 5
7 1,2,3 :
8 4 :
9 1,4 :
10 2,4 511 1,2,3,4,5,6,
7,8,9
Luna Light Source Range
8
NOTE:
With DIP switch 10 OFF, the
light source will not
illuminate unless a DMX
signal is present.

CONNECTION LUNA 0-10V
This is external current source dimming - the light source dimming input requires an
external 0-10V source.
There are three connections required - the ibre port, the mains supply cable and the
0-10V control cable. The ibre port should be connected irst. Connect and secure
the ibre optic connector into the collar and secure using the M5 locking screw.
Connect the PSU/driver to the DC input jack socket on the Luminaire. Plug the mains
plug into the electrical supply socket. Switch on power the led Indicator will
illuminate and the light source is ready or use. I no light is produced consult the
TROUBLESHOOTING section.
THE LIGHT SOURCE WILL NOT ILLUMINATE UNLESS DIP SWITCH 10 IS ON AND A 0-10V
SIGNAL IS PRESENT
NOTE: THESE LIGHT SOURCES ARE NOT MAINS DIMMABLE
Connect up the 0-10V control cable to the mini XLR sockets on the rear o the light
source. The recommended plug or these sockets is the Multicomp SVP556-TA. The
pin out details or these plugs are shown below. Either socket may be used as 0-10V
IN or 0-10V OUT
NOTE: CONVERTORS ARE AVAILABLE FROM UFO
Mini XLR to RJ45
Mini XLR to normal 3 pin XLR
Universal Fibre Optics 9

0-10V SETTINGS
The ollowing table represents light output percentage against approximate control
value input.
NOTE:
THE LIGHT SOURCE WILL NOT ILLUMINATE UNLESS A 0-10V CONTROL VOLTAGE
IS PRESENT.
Light Output Percentage Voltage
100% 7 - 10V
90% 6.2V
80% 5.8V
70% 5.4V
60% 5V
50% 4.5V
40% 3.9V
30% 3.2V
20% 2.3V
10% 1.4V
5% 1.1V
2.5% 0.8V
1.25% 0.4V
0% 0.2V
Luna Light Source Range
10