UFO UFO MIC100P-3 User manual

M croLED 100P V2 Illum nator
Models covered by th s manual:
UFO MIC100P-3
UFO MIC100P-4
UFO MIC100P-6
Please read th s manual fully before nstall ng, operat ng or perform ng
ma ntenance on the llum nator un t.
Illum nator User Gu de
Issue 2 | Rev sed: 15112016
Un versal F ber Opt c L ght ng LLC
6119A Clark Center Avenue | Sarasota | FL34238
Tel: [phone] | 800-UFO-5554
www.f beropt cl ght ng.com

M c100P V2 Illum nator
INTRODUCTION
Thank you for purchas ng th s UFO llum nator.
Please read these nstruct ons fully before connect ng your un t to the electr cal
supply, and keep them for future reference.
The UFO M c100P ut l ses a wh te l ght array and s su table for use w th e ther glass
or PMMA f ber opt c harnesses.
The M c100P s powered by a 100-240 VAC power supply un t.
We do not recommend that the llum nator be le on for 24 hours a day, 7 days a
week as LED l fe w ll be mpa red. A sw tch off of 30m ns per day s recommended.
The UFO M c100P wh te l ght array s ava lable n three target colour temperatures:
UFO M c100P-3: warm wh te (3000K)
UFO M c100P-4: neutral wh te (4000K)
UFO M c100P-6: cool wh te (6000K)
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
2

Un versal F ber Opt c L ght ng LLC 3
INSTALLATION INSTRUCTIONS
POWER SUPPLY REQUIREMENTS
The llum nator s powered by an AC adapter power supply un t. Remove the AC
adapter PSU from ts box.
Connect the jack plug nto the socket n the back, and the llum nator s now ready
for connect on.

M c100P V2 L ght Source
4
MAINTENANCE
D sconnect un t from power supply and allow to cool before attempt ng any
clean ng of the un t.
A v sual check of the un t should be completed every 12 months. However clean ng
should take place as and when requ red.
The body of the un t can be cleaned w th a so, damp cloth - do not use any
abras ves on the un t.
CLEANING THE UNIT
CONNECTION
There are 2 connect ons requ red - the f ber port and the ma ns supply. The f ber
port should be connected f rst. Connect and secure the f ber opt c connector nto
the front of the un t, and secure us ng the M5 lock ng screw.
Plug the ma ns plug nto the electr cal supply socket. Sw tch on the power, the LED
nd cator w ll llum nate, and the llum nator and the decorat ve wheel w ll start up
automat cally. If no l ght s produced consult the troubleshoot ng sect on.
NOTE: THESE ILLUMINATORS ARE NOT MAINS DIMMABLE.

Un versal F ber Opt c L ght ng LLC 5
MAINTENANCE (continued)
Date Maintenance Undertaken
P ease note that a record of a maintenance MUST be kept in the tab e be ow,
indicating what maintenance was undertaken and when. This must be DATED
for warranty purposes.

M c100P V2 L ght Source
6
TROUBLESHOOTING
Problem Probable ca se(s) Remedy
Unit is dead - LED power
indicator is not
ill minated
Mains su ly off Check su ly and reinstate
Loose mains lugs Check lugs
PSU failed Re lace PSU
Unit is dead - no light
o tp t b t LED power
indicator is still
ill minated
LED array failure Re lace LED unit
Poor light o tp t on fiber
Unit needs cleaning
Carefully clean LED Lens
with dry cloth
Clean fiber common end
Fiber ort connector not
lugged in correctly
Ensure lugged in correctly
and secured with locking
screw

Un versal F ber Opt c L ght ng LLC 7
TECHNICAL SPECIFICATIONS
Description Details
Port connector size 30mm
Fiber type Glass/PMMA
S pply voltage 100 - 240V AC, 50/60 Hz
PSU O tp t 12DC, 1.5A, 18W Maximum
LED Power 3W
Min Ambient Temperat re -10ºC
Max Ambient Temperat re +45ºC
Power Connection 2.1 x 5.5 x 12mm
LED Type / Model White light
LED Life 50,000 hours in ambient 25ºC
Operating environment Indoor / dry
Material ABS
Size (L)137mm x(W) 114mm x (H)73mm
(L)5.39” x (W)4.49” x (H)2.87”
Weight with PSU 480.3 g (1.06 lb)

Un versal F ber Opt c L ght ng LLC
6119A Clark Center Avenue | Sarasota | FL34238
Tel: [phone] | 800-UFO-5554
www.f beropt cl ght ng.com