UFO Unidrive CC9 Specification sheet

PRODUCT USER GUIDE
Unidrive CC9 Driver
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE DRIVER UNIT
Rev: C2

Thank you for purchasing this low voltage UFO Constant Current Driver.
The CC9 is a compact 350mA output constant current multi-function driver designed to drive
UFO constant current LED fittings up to 16W. Constant voltage LEDs cannot be connected to this
driver. Please refer to the specific section within this manual for wiring/connection guidance.
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT,
ITS COMPONENT PARTS AND THE HAZARDS INVOLVED.
ELECTRICAL WIRING AND CONNECTION MUST BE CARRIED OUT BY A SUITABLY QUALIFIED
PERSON OBSERVING ALL LOCAL AND STATUTORY ELECTRICAL AND SAFETY REGULATIONS.
WARNING
This driver is designed to work with constant current LED fittings operating on a 350mA output .
Connecting this driver to any other LED devices may result in catastrophic failure of the LED
device and/or the CC9 driver. Always check the input current and voltage of the LED devices to
ensure compatibility prior to powering up the system.
Never hot swap LED fittings. When adding or removing LED fittings always power
down the system first.
WARNING
This driver is designed to work on a DC input voltage of 12-48V ONLY. The DC PSU supplying this
driver must have an output capability suicient to power up the driver and maintain the output
load.
This CC9 driver is suitable for indoor/dry areas and must not be installed in damp or wet
conditions.
INTRODUCTION
UNIDRIVE CC9USER GUIDE
2

The UFO Unidrive CC9 driver supplies a constant current of 350mA at output voltages between
3.2 and 48V. All UFO LED Fittings are 350mA constant current devices. These LED Fittings have a
maximum voltage of 3.2V DC and provide a 1.1 Watt output.
The UFO Unidrive CC9 driver has a low voltage DC input. Therefore the PSU used to supply the
CC9 is selected based upon the total number of fittings the CC9 will be driving.
Number of
LED fings
Max Volts
DC
Total Was
DC
Standard UFO
UK PSU
Standard UFO
EU PSU
1 3.2 1.1 700482 12V 2A 24W PSU UK 700481 12V 2A 24W PSU EU
2 6.4 2.2 700482 12V 2A 24W PSU UK 700481 12V 2A 24W PSU EU
3 9.6 3.3 700482 12V 2A 24W PSU UK 700481 12V 2A 24W PSU EU
4 12.8 4.4 700111 24V 0.75A 18W PSU 700111 24V 0.75A 18W PSU
5 16 5.5 700111 24V 0.75A 18W PSU 700111 24V 0.75A 18W PSU
6 19.2 6.6 700111 24V 0.75A 18W PSU 700111 24V 0.75A 18W PSU
7 22.4 7.7 700111 24V 0.75A 18W PSU 700111 24V 0.75A 18W PSU
8 25.6 8.8 700485 36V 1.66A PSU 700485 36V 1.66A PSU
9 28.8 9.9 700485 36V 1.66A PSU 700485 36V 1.66A PSU
10 32 11 700485 36V 1.66A PSU 700485 36V 1.66A PSU
11 35.2 12.1 700485 36V 1.66A PSU 700485 36V 1.66A PSU
12 38.4 13.2 Special Order Special Order
13 41.6 14.3 Special Order Special Order
14 45.5 15.4 Special Order Special Order
WARNING
Connecting too many constant current LED fittings to the CC9 driver with excessive maximum
voltage output or using an underrated PSU will result in the driver shutting down.
Always check the maximum output voltage of the fittings and ensure that based on 3.2V per LED
an adequate number of fittings are connected, and a suitable rated input PSU for the CC9 driver
is selected, prior to powering up the system.
OUTPUT CAPACITY
3
UFO LIGHTING

Device Funcon
APower input jack socket (2.5mm centre posive). DC input voltage 12V to 48V
dependent on number of LED fings connected
B
DMX input/output screw terminals. Data posive, data negave and ground.
Occupies two DMX channels – Channel 1 LED dimming, Channel 2 LED ON/OFF.
Use for DMX control or Master Slave link to other CC9 drivers
C Funcon LED – indicates signal and control presence
DPower and fault LED – indicates power input and overcurrent, short circuit and
over temperature faults (flashing)
EFuncon DIP switch – sets different funcons (manual, DMX, sensor input etc.)
and also addressing for DMX. Switch down for ON up for OFF
F010V input screw terminals. Posive and negave current source (external
receiving voltage) 010V dimming voltage input (0 to 100%)
GManual (current sink) dimming screw terminals – 10V on screw terminals adjusted
by external electronic potenometer. Normally linked out when not in use
HConstant current screw terminal output LED + and common ground
JFADE IN potenometer. Adjusts the fade in me for sensor operaon between 1
and 12 seconds
KDELAY potenometer. Adjusts the on me for sensor operaon (between fade in
and fade out) from 1 sec to approximately 5 minutes
LFADE OUT potenometer. Adjusts the fade out me for sensor operaon between
1 and 12 seconds
MSensor input – one normally open (N/O – goes open circuit to trigger FADE IN)
one normally closed (N/C – goes closed circuit to trigger FADE IN)
FUNCTIONAL INFORMATION
UNIDRIVE CC9USER GUIDE
4

IMPORTANT
Connect ALL LEDs, electrical control and output wiring connections for the complete system
BEFORE setting up the driver and connecting the driver PSU to the mains supply – see drawing
above and set up instructions below.
Never hot swap LED fittings. When adding or removing LED fittings always power down the
system first.
TYPICAL WIRING CONNECTIONS
5
UFO LIGHTING

ALWAYS carry out ALL wiring connections and set up stages prior to connecting power to the
driver.
NO DIMMING OPERATION
For no dimming operation, all of the manual and remote controls are disabled.
EITHER
DIP SWITCH 1-9 OFF DIP SWITCH 10 ON REMOVE CURRENT SINK LINKS (G)
OR
DIP SWITCH 1-10 OFF INSERT CURRENT SINK LINKS (G)
MANUAL DIMMING OPERATION (CURRENT SINK)
For manual dimming using an electronic potentiometer, the current sink screw terminal link must
first be removed – and a potentiometer connected, in its place. Only compatible electronic
potentiometers recommended by UFO are to be used.
DIP SWITCH 1-9 OFF DIP SWITCH 10 ON REMOVE CURRENT SINK LINK (G)
0-10VDIMMING - CURRENT SOURCE
0-10V dimming (current source) requires an external varying 0 to 10V DC control voltage. The
control voltage will dim both LED outputs simultaneously. See 0-10V value table on following
pages.
DIP SWITCH 1-9 OFF DIP SWITCH 10 ON INSERT CURRENT SINK LINK (G)
DMX DIMMING AND CONTROL
NOTES:
The CC9 driver occupies two DMX channels – see DMX Channel Table on page 8.
For guidance on DMX address switch settings see DMX Address Table on page 8.
DIP SWITCH 10 OFF DIP SWITCH 1-9 TO DMX ADDRESS VALUE INSERT CURRENT SINK LINK (G)
CONNECT ELECTRONIC POT (G)
CONNECT 0-10V INPUT +VE & -VE TO TERMINALS (F)
DRIVER SETUP
UNIDRIVE CC9USER GUIDE
6

Sensor input may either be Normally Open (N/O) or Normally Closed operation. For N/O operation
the sensor must go open circuit to operate the driver. For N/C operation the sensor must go closed
circuit to operate the driver.
The sensor circuit has three timers FADE IN, DELAY & FADE OUT. These timers are adjusted by
trimmer potentiometers (J, K & L), see sensor table on page 8.
MASTER CONTROL
DIP SWITCH 10 ON REMOVE CURRENT SINK LINKS (G) CONNECT DMX LINK CABLES TO SLAVE UNITS
SLAVE CONTROL
DIP SWITCH 1-10 OFF INSERT CURRENT SINK LINKS (G)
SENSOR INPUT
NORMALLY OPEN
DIP SWITCH 1 &10 ON REMOVE CURRENT SINK LINKS (G) CONNECT SENSOR TO N/O TERMINALS (M)
NORMALLY CLOSED
DIP SWITCH 2 &10 ON REMOVE CURRENT SINK LINKS (G) CONNECT SENSOR TO N/C TERMINALS (M)
NOTE:
Where a movement sensor is used to trigger the input, the DELAY and FADE OUT timers will not run
to completion until all movement has ceased.
DRIVER SETUP
7
UFO LIGHTING

Channel
No. Funcon Value
01 LED Output Dimming 0255 No light to maximum light ouput
02 LED Output On 0250
02 LED Output Off251255
DMX CHANNEL TABLE
Value DC
Volts Descripon
0 0.47 LED Output Off
0.48 LED Output Minimum Illuminaon
10 LED Output Maximum Illuminaon
0-10VCHANNEL TABLE
Trimmer Range (approx.) Descripon
Fade In 1 10 seconds On sensor operaon, fades in LED output
from zero to maximum light
Delay 1 300 seconds Maintains LED output at maximum light
Fade Out 1 10 seconds Aer delay, mer fades out LED output from
maximum to zero light
SENSOR TABLE
NOTE:
The trimmer potentiometers are set for minimum (seconds) at full counter clockwise rotation,
maximum seconds) at full clockwise rotation.
INFORMATION TABLES
UNIDRIVE CC9USER GUIDE
8

0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481
2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483
4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484
5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485
6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486
7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487
8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488
9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489
10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490
11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491
12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492
13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493
14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494
15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495
16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496
17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497
18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498
19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499
20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500
21 53 85 11 149 181 213 245 277 309 341 373 405 437 469 501
22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502
23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503
24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504
25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505
26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506
27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507
28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508
29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509
30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510
31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511
S1 S2 S3 S4 S5
0 0 0 0 0
1 0 0 0 0
0 1 0 0 0
1 1 0 0 0
0 0 1 0 0
1 0 1 0 0
0 1 1 0 0
1 1 1 0 0
0 0 0 1 0
1 0 0 1 0
0 1 0 1 0
1 1 0 1 0
0 0 1 1 0
1 0 1 1 0
0 1 1 1 0
1 1 1 1 0
0 0 0 0 1
1 0 0 0 1
0 1 0 0 1
1 1 0 0 1
0 0 1 0 1
1 0 1 0 1
0 1 1 0 1
1 1 1 0 1
0 0 0 1 1
1 0 0 1 1
0 1 0 1 1
1 1 0 1 1
0 0 1 1 1
1 0 1 1 1
0 1 1 1 1
1 1 1 1 1
S9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
S8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
S7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
S6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Switches S6 to S9
Switches S1 to S5 DMX Address
DIP Switch Setting
0=O
1=On
Switches S1-S5
DMX ADDRESS TABLE
9
UFO LIGHTING

Problem Probable Causes Remedy
[GENERAL]
System is dead power LED (D) not lit
No light output from LED
Mains supply o Check supply and reinstate
Loose mains plugs Check plugs
Loose DC output wire or
connection
Check all connections
PSU failed - check output with
DVM
Replace PSU
Driver PCB failure Replace driver
[GENERAL]
One output channel is dead
Power LED (D) is lit
Loose output wire to dead
channel or faulty/poorly fitting
power in on extrusion. Check
output with DVM
Check all connections
Driver PCB failure Replace driver
[NO DIMMING MODE]
System is dead power LED (D) lit
No light output
Current sink input link in place -
DIP switch 10 on
Switch 10 o or remove link
Loose output GND wire or poorly
fitting power in on extrusion
Check all connections
PSU failed - check output with
DVM Replace PSU
Driver PCB failure Replace driver
[MANUAL DIMMING MODE]
Power LED (D) lit – funcon LED (C)
not lit – output LED devices
illuminated but not dimming
Switch 10 o Switch 10 to on
Electronic potentiometers wired
incorrectly - wrong polarity
Check polarity of connections
and reconnect correctly.
[010V DIMMING MODE]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices illuminated but
not dimming
Switch 10 is o Switch 10 to on
[010V DIMMING MODE]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices not illuminated
0-10V wired incorrectly - wrong
polarity
Check polarity of connections
and reconnect correctly
0-10V control signal missing
check input with DVM
Check all connections and output
of 0-10v controller using DVM
[010V DIMMING MODE]
Power LED (D) lit funcon LED (C) lit.
Output LED devices illuminated but
flickering
0V from 0-10V control signal is
missing
Check all connections and output
of 0-10V controller using DVM
TROUBLESHOOTING
UNIDRIVE CC9USER GUIDE
10

Problem Probable Causes Remedy
[DMX DIMMING MODE]
Power LED (D) lit funcon LED (C) lit.
Outpur LED devices illuminated but
responding to DMX
DMX address not set on DIP
switches 1-9
Set DMX address
[DMX DIMMING MODE]
Power LED (D) lit funcon LED (C) lit.
Output LED devices not illuminated and
not responding to DMX
Switch 10 is on Switch 10 o
Incorrect DMX address set Set correct DMX address
[DMX DIMMING MODE]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices illuminated but
not responding to DMX
DMX control signal missing Check all connections are secure
and correct polarity and confirm
output of DMX controller and/or
previous DMX device in DMX chain
[SLAVE MODE]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices illuminated but
not responding to master control
Master driver not set up correctly Check master driver set up
DMX control signal from master
driver missing
Check all connections are secure
and correct polarity and confirm
output of master driver and/or
previous devices in master / slave
DMX chain
[N/O or N/C SENSOR OPERATION]
Power LED (D) lit funcon LED (C) not
lit. Outpur LED devices illuminated but
not responding to sensor
Switch 10 is o Switch 10 to on
[N/O SENSOR OPERATION]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices not illuminated
and not responding to sensor
Switch 1 is o Switch 1 to on
Current sink input link in place Remove link
[N/C SENSOR OPERATION]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices not illuminated
and not responding to sensor
Switch 2 is o Switch 2 to on
Current sink input link in place Remove link
[N/O or N/C SENSOR OPERATION]
Power LED (D) lit funcon LED (C) not
lit. Output LED devices not illuminated
and not responding to sensor
Sensor control signal is missing Check all connections and output
of sensor using DVM
Sensor wired to wrong input Check input connections and
rewire
TROUBLESHOOTING
11
UFO LIGHTING

Problem Probable Causes Remedy
[SHORT CIRCUIT]
Output LED devices go out and power
LED (D) flashes rapidly
Short circuit between LED output
and GND
Check for short circuit on output
cables using a DVM. Repair or
replace faulty cables or devices.
[OVER CURRENT]
Heavily loaded system Output LED
devices go out momentarily and power
LED (D) flashes rapidly
System overloaded beyond 30W Reduce load by removing some
LED fittings until a safe working
load of not more than 30W is
achieved
[OVER TEMPERATURE]
Output LED devices go out momentarily
and power LED (D) flashes rapidly
Driver ambient temperature too
hot
Re-site driver to cooler ambient
environment
TROUBLESHOOTING
UNIDRIVE CC9USER GUIDE
12

Product Name UFO Unidrive CC9
UFO Product Code
DRCC4816DCU driver with single integral dimming potenometer
DRCCDC4816ALLCU driver with fully funconal manual / dmx / 010V /
sensor control
Descripon 16W fully funconal dimmable constant current driver
Input Power 1248V DC
Rated Power 16W maximum output
Output Current 350mA
Connecon Power 2.1mm input jack plug / Control & Outputs screw terminals
Protecon SCP / OCP / OTP
Funconality
Individual manual (current sink) dimming with electronic potenometer
010V (current source) output dimming
DMX with 2 channels (LED dimming & on/off). Controllable from DMX sys
tem or can operate standalone
master/slave with other CC9 drivers.
2 channels (N/O & N/C) sensor input to trigger output LED devices with fade
in, delay and fade out controls.
Ambient Temp. Min. 20°C to Max. +45°C
IP Rang IP20 for indoor use only
Dimensions 146mm (5.75”) x 68mm (2.68”) x 40mm (1.57”)
Accessories Unidim CVD3 (DMELECXXXXXXD) single electronic (current sink)
potenometer on mounng plate
TECHNICAL SPECIFICATIONS
13
UFO LIGHTING

NOTES
UNIDRIVE CC9USER GUIDE
14

NOTES
15
UFO LIGHTING



DESIGN SPECIFY BUILD INSTALL
United Kingdom •United States •Germany •Europe •UAE
UFO Licht GmbH
Friendsfactory AG \Gutenbergstraße 1
85737 Munchen \Deutschland
[phone]
www.ufo-licht.de
Universal Fiber Optics USA LLC
1749 Northgate Blvd
Sarasota \ FL34234 \USA
941-343-8115
www.fiberopticlighting.com
Universal Fibre Optics Ltd
Home Place \Coldstream
TD12 4DT \UK
[phone]
www.ufo.lighting