UFO MicroLED 1000P Specification sheet

PRODUCT USER GUIDE
MicroLED 1000P Illuminator
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE ILLUMINATOR UNIT
E357731
Rev: C3

INTRODUCTION
MICROLED 1000PUSER GUIDE
2
Thank you for purchasing this UFO illuminator/luminaire.
To ensure that the illuminator is set up optimally and gives a long service life, please read this
user guide before installing, operating or performing any maintenance on the unit.
Please keep this User Guide for future reference. This User Guide is laid out in three sections
Installation -details on how to connect your luminaire
Operation - details how to programme and set up your luminaire
Maintenance - maintenance log, troubleshooting guide, technical specification
MODELS COVERED BY THIS USER GUIDE
UFO MIC1000P
IMPORTANT
This product must be installed in accordance with the applicable installation code, by a person
familiar with the construction and operation of the product, and the hazards involved.
These illuminators are not mains dimmable.
The LED array and heatsink in this illuminator can be replaced when it reaches end of life.
Contact UFO for details.
Type Y Attachment: If the external flexible cable or cord of this luminaire or associated
PSU/driver is damaged, it shall be exclusively replaced by the manufacturer or his service agent
or a similar qualified person to avoid a hazard.
Location: Do not locate this illuminator closer than 200mm from any flammable surface.
Clearance / Ventilation: It is imperative that a gap of 200mm is le around the unit. This is to
allow air to circulate and prevent overheating. The location must have free ventilation and must
not have an ambient temperature higher than that specified for the luminaire.
Mounting: This luminaire comes with an integral mounting plate for securing the unit to a
vertical or horizontal surface. Refer to the instruction sheet supplied with the plate.
Warning: Never look directly at the luminaire through the fiber port of the illuminator.
Warning: The luminaire should be positioned so that prolonged staring into the
luminaire at a distance closer than 2.7 metres is not expected.

MOUNTING
This luminaire is powered by a 12V Power Supply Unit or 12V Constant Voltage Driver. Remove
the PSU/driver from its box.
Power supplies are available to suit UK, European and USA power outlets. The UK model is
shown below.
POWER SUPPLY REQUIREMENTS
Plug the jack plug into the socket in the back of the illuminator, and the unit is now ready for
connection.
INSTALLATION
3
UFO LIGHTING
This luminaire supplied with a separate mounting plate. If using the mounting plate refer to the
fitting instructions supplied with it.

There are 2 connections required - the fiber port and the mains supply. The fiber port should be
connected first. Connect and secure the fiber optic connector into the front of the unit and
secure using the M5 locking screw.
Plug the mains plug into the electrical supply socket. Switch on the power, the LED indicator
will illuminate, and the illuminator will start up automatically. If no light is produced consult the
troubleshooting section of this manual.
Note that these illuminators are not mains dimmable.
CONNECTION
The illuminator has 2 color cycles, each with 3 dierent speed settings, the colors are
detailed in the table below:
OPERATION
Cycle Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 7
1 White Red Orange Jade Green Cyan Blue
2Red Orange Jade Green Cyan Blue White
The illuminator is controlled using the 2 push buttons on the rear of the unit.
The upper button stops and starts the color cycle.
The lower button is used to select the cycle speed as follows:
Push the lower button repeatedly until the color white is displayed. The illuminator is now in
Cycle 1 Speed A as detailed in the table below. Each push reduces the speed. On the third push,
the color red will be displayed. The illuminator is now in Cycle 2 Speed A.
At any time the cycle can be stopped on a color and started again using the upper push
button.
Cycle Speed A Fastest Speed B Slower Speed C Slowest
1 (White Start) Push once Push once Push once
2 (Red Start) Push once Push once Push once
OPERATION
MICROLED 1000PUSER GUIDE
4

Note: please complete relevant troubleshooting procedures before returning the unit to us for
further investigation.
Problem Possible Cause(s) Remedy
Unit is dead 
LED power
indicator is not
illuminated
Mains supply offCheck supply and reinstate
Loose mains plugs Check plugs
PSU failed Replace PSU
Unit is dead no
light output but
LED power
indicator is sll
illuminated
LED array failure Contact UFO
Poor light
output on fiber
Unit needs cleaning
Carefully clean LED Lens
with dry cloth
Clean fiber common end
Fiber port connector not
plugged in correctly
Ensure plugged in correctly
and secured with locking
screw
Staonary on
one color
Upper buon has been
pressed Press upper buon once
LED driver has failed Contact UFO
Color cycle can
not be
stopped
LED driver has failed Contact UFO
TROUBLESHOOTING
5
UFO LIGHTING

MAINTENANCE LOG
Date Maintenance Undertaken
Note: a record of all maintenance MUST be kept in the table above, indicating what
maintenance was undertaken and when. This MUST be dated for warranty purposes.
MAINTENANCE
MICROLED 1000PUSER GUIDE
6

TECHNICAL SPECIFICATION
7
UFO LIGHTING
Port connector size 30mm diameter
Fiber type Glass / PMMA
Material/Finish ABS (black, silver or white)
Dimensions (L x W x H) 132mm (5.2”) x 98mm (3.9”) x 67mm (2.6”)
Weight 0.3kg
Operang Environment Indoor use IP20
Min Ambient Temp. 10°C
Max Ambient Temp. +45°C
LED Array Type RGBW
LED Array Power 25W
LED Array Model Cree XLamp MCE
LED Array Life (L70, B10) > 50,000 hours @ 25°C
Wavelength and
Luminous Flux
Red: 625nm / 45lm
Green: 530nm / 93lm
Blue: 460nm / 12lm
White: 3500K / 120lm
Color Change
Funconality Push buon manual color change
Supply Voltage 90264Vac
Mains Running Current 0.03A @ 240Vac
Mains Voltage VA rang 8VA
External PSU Type Power Pax, 12V, 2A, 24W



DESIGN SPECIFY BUILD INSTALL
United Kingdom •United States •Germany •Europe •UAE
UFO Licht GmbH
Friendsfactory AG \Gutenbergstraße 1
85737 Munchen \ Deutschland
[phone]
www.ufo-licht.de
Universal Fiber Optics USA LLC
1749 Northgate Blvd
Sarasota \FL34234 \USA
941-343-8115
www.fiberopticlighting.com
Universal Fiber Optics Ltd
Home Place \Coldstream
TD12 4DT \UK
[phone]
www.ufo.lighting