UFO MIC4000x2 User manual

MicroLED Illuminator Range
Models covered by this manual:
FO MIC4000x2
Please read this manual fully before installing, operating or performing
maintenance on the illuminator unit.
Illuminator User Guide
Issue 2 | Revised: 170317
Universal Fiber Optics
6119A Clark Center Avenue | Sarasota | FL34238
Tel: [phone] | 800 UFO 5554
www.fiberopticli htin .com

MicroLED Illuminator Ran e
INTRODUCTION
Thank you for purchasin this UFO Illuminator.
Please read these instructions fully before connectin your unit to the electrical
supply, and keep them for future reference.
The UFO MicroLED ran e of illuminators utilises an RGBW LED array and is suitable
for use with either lass or polymer fiber-optic harness
The MicroLED is powered by a 100-240 VAC remote desktop power supply unit.
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
2

Universal Fiber Optics 3
INSTALLATION INSTRUCTIONS
POWER SUPPLY REQUIREMENTS
The LED Illuminator is powered from a multifunction, multi-volta e, desk top Power
Supply Unit. Remove the SW4047B Desk Top PSU from its box. This PSU is a multi-
plu device caterin for UK, European and USA plu s.
Select the correct plu and slide it into the receptacle until it clicks securely into
place as shown below:
The plu can be removed by squeezin to ether the plastic retainin lu s and
slidin the plu back out.
Connect the jack plu into the socket in the back, and the illuminator is now ready
for connection.
DO NOT FIT BATTERIES
TO THE REMOTE
CONTROL UNTIL YOU
HAVE FULLY READ THE
INSTRUCTIONS ON
PAGE 4

MicroLED Illuminator Ran e
4
CONNECTION
There are 3 connections required – the 2 x fiber ports and the mains supply. The fiber ports
should be connected first. Connect and secure the fiber optic connector into the front of the
unit and secure usin the M5 lockin screw
Plu the mains plu into the electrical supply socket. Switch on power the led Indicator will
illuminate and the illuminator will start up automatically. If no li ht is produced consult the
TROUBLESHOOTING section
NOTE: THESE ILLUMINATORS ARE NOT MAINS DIMMABLE.
MIC4000x2 REMOTE CONTROLLER
Specification:
Descri tion Details Comments
Power 2 X AAA batteries
Range 30 eters Measured in free space, ay be attenuated by
obstructions or other RF devices
Frequency 2.4GHz Approved for use in UK, Europe and USA
Batter es – With The LED Illuminator powered up as described above, remove the rear cover
on Remote Controller. Tak ng care not to touch any of the front cover buttons, insert the
batteries. If you touch the remote control buttons when insertin the batteries it WILL effect
the operation of your Remote Control. If you do accidentally touch any of the buttons,
remove the batteries and start a ain.Once the batteries are inserted do not use the Remote
Control for 3 seconds.
Test remote control functions as detailed on pa e 5. The Remote Controller is “matched” to
the Illuminator at the factory. If the Remote Controller is not matched or an additional or
replacement Remote Controller is required (see NOTE 2) for the Illuminator proceed to the
Matchin Mode as follows. If a Remote Controller is to be removed from control of a
Illuminator proceed to Unmatchin Model on pa e 5.
DO NOT TOUCH THE
BUTTONS WHILST
INSERTING
BATTERIES

Universal Fiber Optics 5
REMOTE OPERATION
No Descri tion Function
01 Button Power ON
02 Button Power OFF
03 Color Ring Touch control all colors (White not available)
04 Indicator Indicates Controller active when buttons pressed
05 Button Increase color cycle speed
06 Button Increase Brightness
07 Button Decrease Brightness
08 Button Decrease Color cycle speed
09 Button Mode + Step up through Color cycle progra es
10 Button Mode - Step down through Color cycle progra es
2. OFF
3. Color Ring
9. Mode +
10. Mode -
1. ON
4. Indicator Light
5. Speed +
6. Brightness +
7. Brightness -
8. Speed -
REMOTE CONTROLLER OPERATION
Match ng Remote to Illum nator – Remove the power plu from the rear of the Illuminator,
then replace and once the Indicator Li ht (4.) li hts, touch button 5 within 3 seconds, the
Illuminator will “blink” twice slowly indicatin that the Remote Controller is matched to the
Illuminator.
Unmatch ng Remote from Illum nator - Remove the power plu from the rear of the
Illuminator, then replace and once the Indicator Li ht (4.) li hts, touch and hold button 5
within 3 seconds and the Illuminator will “blink” 9 times indicatin that the Remote
Controller is unmatched from the Illuminator.

MicroLED Illuminator Ran e
6
No Mode Brightness S eed Comment
1Static White Adjustable Not Adjustable To revert to 1 (Static White) at any
ti e touch Color Ring then Mode+
2White and Colors
ixed Adjustable Not Adjustable
Color Ring control – brightness
adjust Color only, not White. To
revert to 2 (Color Ring) at any ti e
touch color ring
3All Colors fade
change Adjustable Adjustable No White
4RGBW fade
change Adjustable Adjustable Red, Green, Blue & White
5RGBW snap
change Adjustable Adjustable Red, Green, Blue & White
67 Colors snap
change Adjustable Adjustable White and Colors ixed
72 Colors snap
change Adjustable Adjustable Red & White
82 Colors snap
change Adjustable Adjustable Blue & White
92 Colors snap
change Adjustable Adjustable Green & White
10 1 Color Flash Adjustable Adjustable Red
11 1 Color Flash Adjustable Adjustable Blue
12 1 Color Flash Adjustable Adjustable Green
13 1 Color Flash Adjustable Adjustable White
14 All Colors snap &
fade Adjustable Adjustable Rando
Mode Funct on Programme L st
NOTES
Mode Buttons – This is not a loop, i.e. touchin the Mode+ button will not eventually brin
you back to Mode 1. To revert to Mode 1, either touch Mode – button repeatedly to step back
up throu h the Mode numbers, or touch Color R ng then Mode+
Color R ng –The Color Rin can be used to select individual colors by touchin the rin and
slidin your fin er around the rin ,
Br ghtness – bri htness can be increased or reduced in any mode usin buttons 6 & 7
Cycle Speed – speed of color cyclin in Modes 3 to 14 can be adjusted usin buttons 5 & 8

Universal Fiber Optics 7
REMOTE RANGE WALK TEST
Once the Illuminator is fully installed carry out a complete ran e walk test and record the ran e in the
table below. This information is essential for maintenance purposes to determine if the
ran e/sensitivity is reducin and also to record dead areas within the Remote Controller’s ran e due to
RF obstructions and/or RF interference.
NOTE 2: Where a Illuminator has more than one Remote Control, reduction in operatin ran e may be
experienced when both (or multiple) Remote Controls are used simultaneously.
Descri tion Date Max Range
Controller 1
Controller 2
Controller 3
Dead Areas
STANDALONE OPERATION
To disable the remote and revert to manual operation press one of the buttons on the rear of the
Illuminator. The Illuminator will now respond to manual commands from the 2 control buttons as
detailed below
OPERATION
The LED Illuminator has 2 color cycles each with 3 different speed settin s as detailed below
Cycle Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 7
1 White Red Orange Jade Green Cyan Blue
2 Pink Red Orange Jade Green Cyan Blue

MicroLED Illuminator Ran e
8
At any time the cycle can be stopped on a color and started a ain usin the Lower push
button
To disable manual operation and revert to remote controller operation, recycle the power to
the Illuminator. The Remote Controller may need to be matched to the Illuminator as
detailed on pa e 5.
DMX OPERATION
The MicroLED4000x2 is pro rammed as a Master unit (See Mode desi nation label on rear of
unit) and is capable of interlinkin to a MicroLED 4000SLx2 Slave Illuminator usin a RJ45
cable. In this Master /Slave confi uration the Slave Illuminator will follow the Master
Illuminator, but no control from a remote DMX controller is possible. Remote DMX control
can only be achieved usin MicroLED SLAVE Illuminators. See MicroLED SLAVE User Guide for
DMX wirin connections
Cycle SPEED A - Fastest SPEED B - Slower SPEED C - Slowest
1 (White Start) Push Once Push Once Push Once
2 (Red Start) Push Once Push Once Push Once
The Illuminator is controlled usin the 2 push buttons on the rear of the unit.
The Lower button STOPS and STARTS the color Cycle
The Upper button is used to select the Cycle speed as follows. Push the Lower button
repeatedly until the color White is displayed. The illuminator is now in Cycle 1 speed A as
detailed below. Each push reduces the speed. On the third push the color Red will be
displayed. The illuminator is now in Cycle 2 speed A

Universal Fiber Optics 9
MAINTENANCE
Date Maintenance Undertaken
Please note that a record of all ma ntenance MUST be kept n the table below, nd cat ng what
ma ntenance was undertaken and when. Th s MUST be dated for warranty purposes.

MicroLED Illuminator Ran e
10
Problem Probable cause(s) Remedy
Unit is dead - LED ower
indicator is not illuminated
Mains supply off Check supply and reinstate
Loose mains plu s Check plu s
PSU failed Replace PSU
Unit is dead - no light out ut but
LED ower indicator is still
illuminated
LED array failure Replace Iluminator
May have been switched off usin
Remote Controller
Recycle power to Illuminator or
switch on usin Remote Controller
Remote Controller range reduced
or ersistently freezing
Remote Controller batteries
failin
Replace batteries as per user uide
instructions and carry out matchin
if necessary
Somethin new causin
interference within operatin
ran e
Check for another device
transmittin RF interference
Remote Controller needs resettin
Power the Remote controller down
by removin and reinstallin the
batteries as per User Guide
instructions
Remote Controller failin Replace Remote Controller
Illuminator Receiver Failin Replace Illuminator
Unit won’t res ond to Remote
Controller
Remote Controller batteries failed Replace batteries and carry out
matchin if necessary
Illuminator in stand alone mode Recycle power to Illuminator
Remote Controller needs resettin
Power the Remote Controller down
by removin and reinstallin the
batteries as per User Guide
instructions
Remote Controller not “matched”
to Illuminator
Carry out “matchin ” procedure as
detailed in REMOTE OPERATION
Remote Controller failed Replace Remote Controller
Illuminator Receiver Failed Replace Illuminator
Poor light out ut on fiber
Unit needs cleanin
Carefully clean LED lens with dry
cloth
Clean Fiber common end
Fiber port connector not plu ed
in correctly
Ensure plu ed in correctly and
secured with lockin screw
In Stand Alone Mode - Stationery
on one color Lower Button has been pressed Press Lower button once
LED Driver has failed Replace Illuminator
In Stand Alone Mode - Color cycle
cannot be sto ed LED Driver has failed Replace Illuminator
TECHNICAL SPECIFICATIONS
Please complete troubleshootin procedures before returnin the unit to us.

Universal Fiber Optics 11
TECHNICAL SPECIFICATIONS
Descri tion Details
Port connector size 2 x 1.18” (30mm)
Fiber ty e Glass/PMMA
Su ly voltage 110-240 VAC, 47-63Hz, 0.58A
PSU Out ut 12V DC, 2A, 24W Maximum
LED Power 4 - 10W in color cycle mode
Min Ambient Tem erature 14°F (-10ºC)
Max Ambient Tem erature 113°F (+45ºC)
Power Connection 2.1 x 5.5 x 12mm
LED Ty e / Model RGBW
LED Life 50,000 hours in ambient 77°F (25ºC)
Remote Controller Frequency 2.4Ghz
Remote Controller Range 30m (dependin on environment)
Remote Controller Power 2 x AAA Batteries
Material ABS
Color Black
Size (L)140mm x(W) 106mm x (H)68mm
(L)5.5” x(W)4.17” x(H)2.68”
NOTES:

Universal Fiber Optics
6119A Clark Center Avenue | Sarasota | FL34238
Tel: [phone] | 800 UFO 5554
www.fiberopticli htin .com