UFO LUNA SLP-3000M Specification sheet

PRODUCT USER GUIDE
Luna SLP Light Source
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT
E357731
Rev: C2

Thank you for purchasing this UFO light source.
To ensure that the light source is set up optimally and gives a long service life, please read this
user guide before installing, operating or performing any maintenance on the unit.
This light source is powered by a 24V Power Supply Unit or 24V constant voltage driver.
Please keep this user guide for future reference.
This light source is suitable for indoor use only unless it is situated in a weatherproof enclosure.
MODELS COVERED BY THIS USER GUIDE
UFO Luna SLP-3000M / UFO Luna SLP-4000M
UFO Luna SLP-3000DMX / UFO Luna SLP-4000DMX
UFO Luna SLP-300010V / UFO Luna SLP-400010V
IMPORTANT
This product must be installed in accordance with the applicable installation code, by a person
familiar with the construction and operation of the product, and the hazards involved.
These light sources are not mains dimmable.
The LED array in this luminaire is not replaceable. When it reaches end of life the whole unit
must be replaced.
Type Y Attachment: If the external flexible cable or cord of this luminaire or associated
PSU/driver is damaged, it shall be exclusively replaced by the manufacturer or his service agent
or a similar qualified person to avoid a hazard.
Location: Do not locate this luminaire closer than 200mm from any flammable surface.
Clearance / Ventilation: It is imperative that a gap of 200mm is le around the unit. This is to
allow air to circulate and prevent overheating. The location must have free ventilation and must
not have an ambient temperature higher than that specified for the light source.
Mounting: This is a fixed luminaire. See mounting plate instruction on page 3 for
fixing to surface.
Warning: Never look directly into the luminaire LED light source.
Warning: The luminaire should be positioned so that prolonged staring into the
luminaire at a distance closer than 0.33m is not expected.
INTRODUCTION
LUNA SLP USER GUIDE
2

ATTACH THE LIGHT SOURCE TO ITS MOUNTING PLATE
Fit the metal mounting plate to the base of the light source before making electrical
connections.
Remove the mounting plate and the four plastic 2 part (screw and rivet body) from the box.
Invert the light source and remove the four rubber feet. Separate the screws from the rivet
bodies and push fit the rivet bodies into the holes vacated by the feet.
Align the plate against the rivets and secure the plate to the light source with the four plastic
screws using an M4 pozi-drive screwdriver. Do not overtighten. The light source can now be
fixed securely to the mounting surface.
Note: Mounting plate diagram is indicative only.
INSTALLATION
3
UFO LIGHTING

The light source is powered from a 24V DC PSU/Constant Voltage SELV LED driver.
The driver caters for UK/European/other mains supplies using the relevant power cord
supplied.
POWER SUPPLY REQUIREMENTS
There are 2 connections required – the fibre port and the mains supply cable. The fibre port
should be connected first. Connect and secure the fibre optic connector into the collar and
secure using the M5 locking screw.
Connect the PSU to the DC input jack socket on the light source, and connect the IEC cable to
the PSU. Plug the mains plug into the electrical supply socket. Switch on power the led
indicator will illuminate and the light source is ready for use. If no light is produced consult the
TROUBLESHOOTING section of this user guide.
Note: these light sources are not mains dimmable.
CONNECTION - LUNA MMODELS ONLY
LUNA SLP-XXXXM CONNECTIONS LUNA SLP-XXXXDMX /10VCONNECTIONS
INSTALLATION
LUNA SLP USER GUIDE
4

There are 3 connections required – the fibre port, the mains supply cable and the DMX control
cable(s). The fibre port should be connected first. Connect and secure the fibre optic connector
into the collar and secure using the M5 locking screw.
Connect the PSU to the DC input jack socket on the light source, and connect the IEC plug to the
PSU. Plug the mains plug into the electrical supply socket. Switch on power – the red LED Indi-
cator will illuminate and the light source is ready for use. If no light is produced consult the
TROUBLESHOOTING section of this user guide.
Connect the DMX control cable(s) to the Mini-XLR socket(s) on the rear of the light source. The
recommended plugs for these sockets are Multicomp SVP556-TA (female) or Multicomp SVP555-
TA (male). The pin out details for the plugs are shown below.
Either socket may be used as DMX in or DMX out.
CONNECTION - LUNA DMX MODELS ONLY
Note: UFO can supply converters for these light sources to allow them to be interfaced to
standard 3 pin XLR connectors or RJ45 connectors.
INSTALLATION
5
UFO LIGHTING

INSTALLATION
LUNA SLP USER GUIDE
6
This is external current source dimming - the light source dimming input requires an
external 0-10V source.
There are three connections required - the fibre port, the mains supply cable and the 0-10V
control cable. The fibre port should be connected first. Connect and secure the fibre optic
connector into the collar and secure using the M5 locking screw.
Connect the PSU to the DC input jack socket on the light source, and connect the IEC cable to
the PSU. Plug the mains plug into the electrical supply socket. Switch on power – the red LED
indicator will illuminate and the light source is ready for use. If no light is produced, consult the
TROUBLESHOOTING section of this user guide.
THE LIGHT SOURCE WILL NOT ILLUMINATE UNLESS DIP SWITCH 10 IS ON AND A 0-10V
SIGNAL IS PRESENT
Connect the 0-10V control cable(s) to the Mini-XLR socket(s) on the rear of the light source. The
recommended plugs for these sockets are Multicomp SVP556-TA (female) or Multicomp SVP555-
TA (male). The pin out details for these plugs are shown below.
Either socket may be used as 0-10V IN or 0-10V OUT
CONNECTION - LUNA 0-10VMODELS ONLY
Note: UFO can supply converters for these light sources to allow them to be interfaced to
standard 3 pin XLR connectors or RJ45 connectors.

OPERATION
7
UFO LIGHTING
USING THE LIGHT SOURCE - LUNA MMODELS ONLY
Under normal operation the LUNA M light source can be dimmed manually using the dimmer
control on the rear of the unit.
USING THE LIGHT SOURCE - LUNA DMX MODELS ONLY
The DMX light sources can be dimmed remotely (single channel 0-255 – see table below) and can
be addressed manually.
Single Channel Value 0 255
Descripon LED offLED brightest
Unless the address is specified on the purchase order, all light sources will be defaulted to
address 001. Connect the DMX controller to either of the Mini XLR sockets, and the light source
can now be dimmed. Additional slave (which are set to the same address) DMX light sources can
be linked together.
1. Disconnect the light source from the mains supply.
2. Tilt the light source on its side and remove the screw from the base as shown below.
3. Slide the access cover down to remove and set the cover and screw aside.
4. Switch DIP switch 10 (top) to ON as shown below.
5. Replace access cover and securing screw.
REVERTING ADMX LIGHT SOURCE TO MANUAL OPERATION MODE

1. Disconnect the light source from the mains supply.
2. Tilt the light source on its side and remove the screw from the base as shown below.
3. Slide the access cover down to remove and set the cover and screw aside.
4. Ensure DIP switch 10 (top) is set to OFF as shown below.
5. Set the address required as detailed in the address table, overleaf.
6. Replace access cover and securing screw,
SETTING THE DMX ADDRESS
Note: for DMX control
operation to work, dip
switch 10 must be in the
o position.
See the table and diagram on the following page for instructions on setting the DMX address
using dip switches.
OPERATION
LUNA SLP USER GUIDE
8

OPERATION
9
UFO LIGHTING
SETTING THE DMX ADDRESS
DMX B Start
Channel # Dip Switches On DMX B Start Channel # Dip Switches On
1 1 11 1,2,4
2 2 12 3,4
3 1,2 13 1,3,4
4 3 14 2,3,4
5 1,3 15 1,2,3,4
6 2,3 16 5
7 1,2,3 : :
8 4 : :
9 1,4 : ;
10 2,4 511 1,2,3,4,5,6,7,8,9
Note: with dip switch 10 OFF, the light source will not illuminate unless a DMX signal is present.

USING THE LIGHT SOURCE - LUNA 0-10VMODELS ONLY
Luna 0-10V models allow the light output to be varied by applying a dierent voltage through the
rear connectors. The following table represents light output percentage against approximate
control value input.
Light Output
Percentage Voltage
100% 7 10V
90% 6.2V
80% 5.8V
70% 5.4V
60% 5V
50% 4.5V
40% 3.9V
30% 3.2V
20% 2.3V
10% 1.4V
5% 1.1V
2.5% 0.8V
1.25% 0.4V
0% 0.2V
Note: the light source will not illuminate
unless dip switch 10 is on and a 0-10V
control voltage is in place.
OPERATION
LUNA SLP USER GUIDE
10

MAINTENANCE
11
UFO LIGHTING
MAINTENANCE LOG
Date Maintenance Undertaken
Note: a record of all maintenance MUST be kept in the table above, indicating what maintenance
was undertaken and when. This MUST be dated for warranty purposes.

PROCEDURES FOR ALL MODEL TYPES
Problem Possible Cause(s) Remedy
Unit is dead –
no light output
and LED power
indicator on
PSU is not
illuminated
Mains supply offCheck supply & reinstate
Loose mains plugs Check plugs
Plug fuse blown (UK) Check fuse. If blown, replace
PSU failed Replace PSU
Unit is dead –
no light output
and LED power
indicator on
PSU is illumi
nated, but LED
indicator on
Light source not
illuminated
PSU failed Replace PSU
Unit is dead –
no light output
but LED power
indicator is
illuminated
DMX dimming at minimum
(for DMX version only)
Adjust brightness on
controller (increase value up
from 0)
DMX fault on controller or
DMX cable
Remove DMX XLR plug from rear of light
source. Light source wil default to full
bright. Repair DMX controller
or cabling.
LED array failure Replace light source
Unit not
responding to
DMX
commands
Address incorrect Check the address set on unit matches
the address set on the controller
DMX cable fault
Refer to manual diagram for correct
wiring terminaon. Carry out connuity
check.
Swap DMX cable for known
good cable
Note: please complete relevant troubleshooting procedures before returning the unit to us for
further investigation.
TROUBLESHOOTING
LUNA SLP USER GUIDE
12

TROUBLESHOOTING
13
UFO LIGHTING
Problem Possible Cause(s) Remedy
Unit is dead 
no light output 
but LED
indicator on
light source is
illuminated.
No 010V dimming to unit
(0V= LED Off)
Refer to manual diagram for
correct terminaon.
Carry out connuity check.
Carry out voltage / polarity
010V cable fault check
010V cable fault
Controller fault
Carry out voltage / polarity
check at controller.
Repair / replace as necessary
010V LED PCB failure Replace 010V PCB
No 010V signal
present
Controller offor failed Check controller. Ensure 0
10V signal present
010V cable faulty
Carry out voltage and
polarity check on mini XLR
plug. Repair as necessary
ADDITIONAL PROCEDURES FOR 0-10VMODELS ONLY
Note: please complete relevant troubleshooting procedures before returning the unit to us for
further investigation.

Descripon Details
Port connector size 30mm diameter
Fibre type Glass / PMMA
Mains Supply Voltage 100240V AC, 4763Hz
PSU Output 24V DC, 0.75A, 18W max.
LED Power 11.5W
Min Ambient Temperature 10°C
Max Ambient Temperature +45°C
Fan 60mm crossflow, 12V
Led Type White light
DMX [specific models only] User addressable 1 channel dimming
010V [specific models only] 010V DC receiving
LED Life 50,000 hours typical
CRI 3000°K >80 (typical) / 4000°K > 75 (typical)
Colour Temperature 3000°K or 4000°K
Material ABS
Finish Grey
Dimensions (L x W x H) / Weight 222mm x 114mm x 81mm / 842g
TECHNICAL SPECIFICATIONS
LUNA SLP USER GUIDE
14

NOTES
15
UFO LIGHTING



DESIGN SPECIFY BUILD INSTALL
United Kingdom •United States •Germany •Europe •UAE
Universal Fiber Optics USA LLC
1749 Northgate Blvd
Sarasota \FL34234 \USA
941-343-8115
www.fiberopticlighting.com
Universal Fibre Optics Ltd
Home Place \Coldstream
TD12 4DT \UK
[phone]
www.ufo.lighting
UFO Licht GmbH
Andreasstraße 20
93059 Regensburg \Deutschland
[phone]
www.ufo-licht.de