Ufo Quasar ufoqua3080-a User manual

UFO LIGHTING

FIBER OPTIC &LED LIGHTING SYSTEMS

REVISION: B3

QUASAR ILLUMINATOR RANGE

USER GUIDE

PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING OR

PERFORMING MAINTENANCE ON THE ILLUMINATOR UNIT.

INTRODUCTION

Thank you or purchasing this UFO illuminator

To ensure that the illumaintor is set up optimally and gives a long service li e, please read this

user guide be ore installing, operating or per orming any maintenance on the unit.

Please keep this user guide or uture re erence.

MODELS COVERED BY THIS USER GUIDE

QUASAR USER GUIDE2

STANDARD CRI RANGE:

HIGH CRI RANGE:

UFO Quasar

Color Temperature CRI Model Funconality

27 - 2700K

80: > 80 CRI

90: > 90 CRI

No Suﬃx: Standard White Light

30 - 3000K E: Emergency White Light

40 - 4000K T: Twinkle Eﬀect Decorave Wheel

50 - 5000K C: Color Segment Decorave Wheel

57 - 5700K CF: Color Segment Decorave Wheel

with Separate Control Feed

65 - 6500K

MODELS COVERED BY THIS USER GUIDE

UFOQUA3080-A UFOQUA4080-A UFOQUA5080-A UFOQUA5780-A UFOQUA6580-A

UFOQUA3080-E-A UFOQUA4080-E-A UFOQUA5080-E-A UFOQUA5780-E-A UFOQUA6580-E-A

UFOQUA3080-T-A UFOQUA4080-T-A UFOQUA5080-T-A UFOQUA5780-T-A UFOQUA6580-T-A

UFOQUA3080-C-A UFOQUA4080-C-A UFOQUA5080-C-A UFOQUA5780-C-A UFOQUA6580-C-A

UFOQUA3080-CF-A UFOQUA4080-CF-A UFOQUA5080-CF-A UFOQUA5780-CF-A UFOQUA6580-CF

UFOQUA2790-A UFOQUA3090-A UFOQUA4090-A UFOQUA5790-A

UFOQUA2790-E-A UFOQUA3090-E-A UFOQUA4090-E-A UFOQUA5790-E-A

UFOQUA2790-T-A UFOQUA3090-T-A UFOQUA4090-T-A UFOQUA5790-T-A

UFOQUA2790-C-A UFOQUA3090-C-A UFOQUA4090-C-A UFOQUA5790-C-A

UFOQUA2790-CF-A UFOQUA3090-CF-A UFOQUA4090-CF-A UFOQUA5790-CF-A

IMPORTANT

This product must be installed in accordance with the applicable installation code, by a person

amiliar with the construction and operation o the product, and the hazards involved.

These illuminators are not mains dimmable.

The LED array in this illuminator is not replaceable. When it reaches end o li e the whole unit

must be replaced.

Type Y Attac ment: I the external lexible cable or cord o this luminaire or associated

PSU/driver is damaged, it shall be exclusively replaced by the manu acturer or his service agent

or a similar quali ied person to avoid a hazard.

Location: Do not locate this illuminator closer than 200mm (8”) rom any lammable sur ace.

Clearance / Ventilation: It is imperative that a gap o 200mm (8”) is le around the unit. This is

to allow air to circulate and prevent overheating. The location must have ree ventilation and

must not have an ambient temperature higher than that speci ied or the luminaire.

Mounting: This luminaire comes with an integral mounting eet or securing the unit to a

vertical or horizontal sur ace.

Warning: Never look directly at the luminaire through the iber port o the illuminator.

Warning: The luminaire should be positioned so that staring into the luminaire at a distance

closer than 2.7 meters (8.9 ) in not expected.

INTRODUCTION

3UFO LIGHTING

QUASAR USER GUIDE4

INSTALLATION

MODEL TYPES

The Quasar LED illuminator incorporates a range o LED arrays to provide optimum display and

illumination within the ollowing optical range.

Model CRI Color Temperature Lumen Output

UFOQUA3080 >80 3000°K 17974

UFOQUA4080 >80 4000°K 18438

UFOQUA5080 >80 5000°K 18653

UFOQUA5780 >80 5700°K 18840

UFOQUA6580 >80 6500°K 18992

UFOQUA2790 >90 2700°K 14805

UFOQUA3090 >90 3000°K 15400

UFOQUA4090 >90 4000°K 15633

UFOQUA5790 >90 5700°K 16174

The Quasar is a 135 - 150W white light LED illuminator with optional decorative wheel

capability. The Quasar LED illuminator driver PCB has all the control unctionality itted as

standard. The ollowing control unctionality and con igurations are available via rear panel

connections, push buttons and LCD display.

1. Manual dimming using rear panel push button controls with status display

2. Manual dimming using a remote potentiometer

3. 0-10V (current source -receiving). Dimming only or two white light models. Two versions or

white light only – standard and emergency light. Emergency light version reverts to maximum

light output when mains power to the 0-10V control system is lost

4. 0-10V (current source -receiving). Two channels dimming and wheel motor control or

decorative model. For separate eed decorative models the 0-10V wheel control input is used

5. 1-10V dimming – one channel (current sink -sending). Dimming or standard white light only,

not available in emergency white light or decorative wheel versions

6. DMX dimming – 5 channels (dimming, color wheel control, color wheel duration, twinkle

wheel control, initialise/reset/LED/ an on and oﬀ) not available in emergency white light

7. Motor Control manual decorative wheel control with speeds rom stop to 4 rpm in

increments. On Color decorative wheel stop is on color 1, on twinkle wheel stop is on open

wheel segment (maximum light output)

8. 28 standalone decorative programmes with bi-directional variable wheel speed control

9. Master slave unctionality – one Quasar acting as master controlling slave Quasar luminaires

via DMX links

5UFO LIGHTING

INSTALLATION

5UFO LIGHTING

CONNECTIONS AND CONTROLS OVERVIEW

0-10V / 1-10V

DIMMING

0-10V WHEEL

CONTROL DMX REMOTE DISPLAY

CONNECTOR

MAINS

INDICATOR

DISPLAY

CONTROL & PROGRAMME

BUTTONS

FUSED IEC

MAINS INPUT

SOCKET

CONNECTION - FOR MANUAL OPERATION

There are two connections required – the iber port and the mains supply cable. The iber port

should be connected irst be ore the mains supply. Connect and secure the iber optic

connector into the collar and the ront o the unit and secure using the M5 knurled locking

screw. Ensure the iber optic connector is ully inserted be ore tightening the locking screw.

Never run t e luminaire wit t e fiber optic connector out of t e collar.

Plug the IEC connector into the IEC socket and then plug the mains connector into a local mains

supply. Switch on power the mains indicator will illuminate and the illuminator is ready or use.

I no light is produced consult the TROUBLESHOOTING section in this manual.

INSTALLATION

QUASAR USER GUIDE6

CONNECTION - FOR REMOTE MANUAL OPERATION

This connection method allows the luminaire to be dimmed remotely using a simple passive

potentiometer control.

There are three connections required – the iber port, the remote dimmer cable and the mains

supply cable. The iber port should be connected irst be ore the mains supply. Connect and

secure the iber optic connector into the collar and the ront o the unit and secure using the M5

knurled locking screw. Ensure the iber optic connector is ully inserted be ore tightening the

locking screw. Never run t e luminaire wit t e fiber optic connector out of t e collar.

Connect the remote dimmer cable (typically CAT5) to the dimmer as shown below. Wire up and

connect the RJ45 plug to the Quasar end o the dimmer cable and plug into connector A the le

hand RJ45 on the rear o the luminaire using pin outs as detailed below. Only the le hand RJ45

connector is used to control dimming in this way.

Plug the IEC connector into the IEC socket and then plug the mains connector into a local mains

supply. Switch on power, the mains indicator will light and the illuminator is ready or use.

I no light is produced consult the TROUBLESHOOTING section in this manual.

1. WHITE/ORANGE

2. ORANGE

3. WHITE/GREEN

4. BLUE

5. WHITE/BLUE

6. GREEN

7. WHITE/BROWN

8. BROWN BLUE +VE

BLUE/WHITE

+VE

BROWN/WHITE

+VE

TOP VIEW OF PLUG

RJ45 - CLIP DOWN, PINS UP CVD1 DIMMER & PLATE

RJ45 Pin No. Wire Color Polarity Funcon

4 Blue +VE Posive 10V Dimming Supply

5 Blue/White +VE Posive (10V) 0-10V Current Source Dimming

7 Brown/White -VE Negave (0V) Remote Potenometer Dimming

RJ45 CONNECTOR A (LEFT HAND) - DIMMING

7UFO LIGHTING

INSTALLATION

CONNECTION - FOR DMX REMOTE CONTROL OPERATION

There are three connections required – the iber port, the DMX cables and the mains supply

cable. The iber port should be connected irst be ore the mains supply. Connect and secure the

iber optic connector into the collar and the ront o the unit and secure using the M5 knurled

locking screw. Ensure the iber optic connector is ully inserted be ore tightening the locking

screw. Never run t e luminaire wit t e fiber optic connector out of t e collar.

Wire up using the DMX cable rom the DMX control system. Solder the cables to the 3 pin XLR

male and emale plug and socket using pin outs as detailed below and plug in to the

connectors on the rear o the luminaire. The image below shows the pin orientation o the

connectors actually itted to the illuminator.

Plug the IEC connector into the IEC socket and then plug the mains connector into a local mains

supply. Switch on power, the mains indicator will light and the illuminator is ready or use.

I no light is produced consult the TROUBLESHOOTING section in this manual.

REMOTE DIMMING NOTES:

• Always use an approved CAT5 cable

• Use a 10kΩ linear potentiometer connected across pins 4, 5 and 7 as detailed on page 6.

See Accessories in Technical Speci ication section at end o this document or UFO CVD1

• The CVD1 is designed to be itted to the back o a one gang aceplate

• Always use an approved DMX cable

• Always “daisy chain” a DMX cable or universe

• Never use a T joint on a DMX cable or universe, unless using and approved inter ace or splitter

• Never connect more than 30 devices to a single DMX universe unless using and approved

inter ace or splitter

• Always terminate the last device on a DMX universe by connecting a 120 ohm resistor across

DMX+ and DMX- across the last output connector

• This is a 2 or 5 channel device. Always leave suﬀicient channels ree when addressing multiple

Quasar luminaires i.e. address 001,003, 005 ( or 2channel DMX), 001,006,011 ( or 5 channel

DMX)

DMX NOTES:

ǖǖǕǕǔǔ





$)ǖʰʫ$)ǕʰȐ$)ǔʰ-*0)

INSTALLATION

QUASAR USER GUIDE8

CONNECTION - FOR 0-10V(CURRENT SOURCE)OPERATION

There are three connections required – the iber port, the 0-10V cables and the mains supply

cable. The iber port should be connected irst be ore the mains supply. Connect and secure the

iber optic connector into the collar and the ront o the unit and secure using the M5 knurled

locking screw. Ensure the iber optic connector is ully inserted be ore tightening the locking

screw. Never run t e luminaire wit t e fiber optic connector out of t e collar.

Wire up and connect RJ45 plugs to the RJ45 connectors on the rear o the luminaire using pin

outs as detailed below. The le hand RJ45 connector controls dimming, the right hand

connector controls the decorative wheel motor. Ensure the 0-10V control system is powered up

and supplying a control voltage.

Plug the IEC connector into the IEC socket and then plug the mains connector into a local mains

supply. Switch on power the mains indicator will illuminate and the illuminator is ready or use.

I no light is produced consult the TROUBLESHOOTING section in this manual.

1. WHITE/ORANGE

2. ORANGE

3. WHITE/GREEN

4. GREEN

5. WHITE/BLUE

6. BLUE

7. WHITE/BROWN

8. BROWN

TOP VIEW OF PLUG

RJ45 - CLIP DOWN, PINS UP

RJ45 Pin No. Wire Color Polarity Funcon

5 Blue/White +VE Posive (10V) 0-10V Current Source Dimming

7 Brown/White -VE Negave (0V) Remote Potenometer Dimming

RJ45 CONNECTOR A (LEFT HAND) - DIMMING

RJ45 Pin No. Wire Color Polarity Funcon

1 Orange/White -VE Negave (0V) 0-10V Current Source Twinkle Motor

3 Green/White +VE Posive (10V) 0-10V Current Source Twinkle Motor

5 Blue/White +VE Posive (10V) 0-10V Current Source Color Motor

7 Brown/White -VE Negave (0V) 0-10V Current Source Color Motor

RJ45 CONNECTOR B (RIGHT HAND) - MOTOR CONTROL

9UFO LIGHTING

INSTALLATION

0-10V NOTES:

• This is a current source 0-10V control system. The input rom the 0-10V controller (source)

supplies a varying control voltage between 0 and 10v to the luminaire to control the dimming

or decorative wheel motors, or both the dimming and the decorative motors

• Always use an approved CAT5 cable

• With no 0-10V input the luminaire will give no light output and the decorative wheel will be

stationary

CONNECTION - FOR 1-10V(CURRENT SINK)STANDARD WHITE LIGHT DIMMING