Viavi T-BIRD-4000 Parts list manual

4000 PLATFORM
GETTING STARTED MANUAL
USER INTERFACE
The 4000 Platform includes the controls and display needed for measurement analysis
The Print function is available by pressing simultaneously the left and right direction
keys.
1
2
3
4
5
6 7 8 9
10
11
12
13
14
15
16
17
14. Direction keys Move the cursors or modify zoom on results pages; scroll through the menu in setup pages 15. Enter Validate an action 16.Start / Stop Start / Stop a measurement 17. Testing indicator Red when a measurement is in progress
11. Setup Calls up the measurement con- guration menu. Depends on the active function. 12. File Calls up the le and directory management menu, used to store les, choose a storage media … 13. Cancel Deselect a function or escape a menu
7. Charge Indicator Lit in red when battery is charg- ing; in green when battery is fully charged 8. TFT Color screen This screen can be touch screen on option 9. Menu keys Different according to the display 10. Results Calls up the results page & is used to analyze results
3. Numeric keypad Enter a numerical value or shortcut to access a function 4. SHIFT Used in combination with another key as shortcut 5. On/Off Start / Stop the 4000 Plat- form 6. On Indicator Lit in x or blinking green
1. Auto: Call the Script Function 2. Home: Give access to - the conguration menus of the instru- ment (choice of module(s) used). - the conguration menus of the sys- tem (screen, date, language, print-out, etc.). Press
System Settings
to congure
the 4000 Platform
Charging the battery
Use only the mains adapter supplied with the MTS/T-BERD 4000. The adapter for some
other electronic device may appear to be identical, but entails a risk of damage to the
MTS/T-BERD 4000.
Connecting the mains adapter
At the top of the MTS/T-BERD 4000 , lift up the power supply socket protector and plug
in the mains adapter.
Connect the adapter to the mains. The On indicator lamp starts blinking in green.
Charging
If the instrument is tted with a battery, on connection to the mains:
-if the user does not press On within 20 seconds, the battery will go on to charge. In
this case, the Charge indicator will be lit in red.
-if the user presses the On button, the instrument starts up and the battery will be
charged during use.
Once the battery is fully charged, the Charge indicator lamp is lit in solid green.
It is essential to wait until charging is complete to ensure maximum independent operat-
ing time, which may otherwise be considerably reduced
TEChNICAl ASSISTANCE
If you require technical assistance, call 1-844-GO-VIAVI. For the latest TAC informa-
tion, go to http://www.viavisolutions.com/en/services-and-support/support/technical-
assistance.
INSTAllING AND REMOVING A MODUlE IN ThE 4000 PlATFORM
The 4000 Platform must be switched off and, if operating on mains, its supply cable
must be unplugged.
Installing a module
1
Turn the instrument face down on the work surface
2
Set the 2 notches on the module part (1a) into the two holes on the Base (1b).
1(b)
2(b)
1(a)
2(a) Captive screws xing the module
1(a)
2(a)
3Make ush the 2 connections (2a & 2b), on module and base.
4
Once positioned, x the module to the base screwing the 2 screws xing the
receptacle
Removing a module
1
Unscrew the two captive xing screws of the plug-in completely (up to the stop).
2
Carefully slide the module out of its slot.
BATTERY MANAGEMENT
The battery supplied with the 4000 Platform must be fully charged before use.
The instructions below apply to the removable Lithium Ion (LiIon) battery inside
the battery compartment.
Access to the battery
Stylus for touchscreen
Kickstand
Battery
1
Switch off the 4000 Platform and disconnect the mains supply.
2
Loosen the screws at the left of the instrument using a Philips head screwdriver
3
Remove the cover of the battery, pulling with the help of the screws.
4
The battery can then be removed, taking care not to damage the connector into
which it is plugged.
When re-seating the battery, make sure that its connector engages correctly with the
4000 Platform. Then t the cover back and lock the screws.
T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 6T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 5 T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 1

SAFETY RECOMMENDATIONS
Laser safety
The provisions contained in two standards dene the safety procedures to be observed
both by users and by manufacturers when utilizing laser products:
-EN 60825-1: 2001 - Safety of laser products – Part 1: Classication of products,
requirements and user guidelines.
-FDA 21 CFR § 1040.10 - Performance standards for light-emitting products - Laser
products.
Due to the range of possible wavelengths, power values and injection characteristics of
a laser beam, the risks inherent in its usage vary. The laser classes form groups repre-
senting different safety thresholds.
-VFL option: Laser Class 2.
Due to the reduced dimensions of the optical modules, it is not possible to attach the re-
quired warning labels to them. In line with the provisions of Article 5.1 of the EN 60825-1
standard, the laser class identication labels are shown below:
Ref. standard EN 60825-1, Edition 1.2, 2001-08 FDA21CFR§1040.10
Class 2
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
CAUTION
LASER RAD IATION - DO NOT
STARE INTO BEAM
CLASS II LASER PRODUCT
The user must take the necessary precautions concerning the optical outputs of the
instrument and follow the manufacturer’s instructions.
Measurements on optical bers are difcult to execute and the precision of the results
obtained depends largely on the precautions taken by the user.
AC/DC power supply safety
In conformance with the recommendations of standard EN 61010, the instrument
should be operated within the manufacturer’s guidelines. Failure to do so may compro-
mise the protection offered by the instruments design.
Do not use any mains adaptor or battery other than those supplied with the instrument,
or supplied by Viavi as an option for this instrument.
The 4000 Platform uses a Lithium ion (LiIon) rechargeable battery and a lithium coin-
cell. This is a long-life battery, and it’s possible that you will never need to replace it.
However, should you need to replace it, refer to your system documentation for instruc-
tions.
Do not dispose of the battery/coin-cell along with household waste. Contact your local
waste disposal agency for the address of the nearest battery/ coin-cell deposit site.
SWITChING ON / OFF ThE 4000 PlATFORM
2
1
Switching on the 4000 Platform
1
If the Platform is to be used on mains, rst plug the mains adapters into the 4000
Platform.
The On indicator blinks in green
2
Press the On/Off key, whether the Platform is working on mains or on battery.
The On indicator changes from blinking to solid green.
The instrument is ready to be used once the Home page or the result page of the
activated function at the previous start is displayed.
Switching off the 4000 Platform
To switch off the instrument, press the On/Off key.
Wait for the On indicator to blink in green before disconnecting the mains.
It is possible to switch over from battery to mains operation, or vice versa, without loss
of data.
TOP PANEl INPUT / OUTPUTS
The upper panel contains, from left to right, the following elements (see example below):
1 2 3 4 5 6 7
1The internal memory extension, optional and unreachable by the user
2The power meter input
3VFL, the corresponding output (red light)
4USB connectors for printer, mouse, keyboard, USB memory stick
5The headset jack
6The RJ 45 connector for the Ethernet interface,
7The connection socket for the mains adapter providing the 15V power supply and
used to charge the battery
CONFIGURING ThE UNIT
When the 4000 Base Unit is to be used for the rst time, or before a measurement
campaign is started, the unit parameters must be congured.
To call up this conguration menu, press HOME, then the menu key System Settings.
Upper
banner
Central
zone
Function
keys
1 SCREEN Allows conguration of the display: backlight, contrast, screen
saver…
2 I/O INTERFACE Allows conguration of the communication interfaces between
the 4000 Platform and a PC
3 COUNTRY Allows conguration of the language to be used and the date /
time
4 AUDIO Allows the activation of the Hands-free or Headset function and
to adjust the sound level for the function selected
5 UTILITY Allows conguration of the options: VFL, automatic shutdown
and Home selection. It also allows the IP address for upgrading
via the network to be specied.
6 PRINTER Allows conguration of the printing function
TOUCH SCREEN This button allows the touch screen to be calibrated, when the
option is available on the 4000 Platform
FACTORY DEFAULT This button allows the system to be congured with the original
parameters set by default in the factory.
The display is divided into 3 zones:
A. UPPER BANNER
Display different icons according to the commands activated. It can also be different
according to the release software installed.
Active application VNC icon
Data saving in progress USB key icon
Print icon Battery & Charge level icons
VFL icon Current date & time
Web icon PDF icon
When the 4000 Platform screen is exported on a remote PC, via a VNC window, click
with the mouse on the upper banner on the PC screen to display a virtual control but-
tons bar for a few seconds.
Click on one of the buttons of this bar to get exactly the same result as when using the
buttons on the front panel of the Platform.
B. CENTRAL ZONE
Display the conguration or the results of measurements. The display depends on the
release software installed.
C. FUNCTION KEYS
At the right side, rigid function keys (or tactile on option). The keys are different accord-
ing to the function selected and the release software installed.
VAlIDATING A FUNCTION
To congure the unit, proceed as follows:
1
Press the HOme button.
The functions available are represented graphically by icons.
Examples:
To validate a function
2
Move on to the icon representing the function to be validated using the direction
keys (or the mouse or external keyboard if the corresponding option is present).
The icon is framed in white
3
Press the enter key to conrm the selection.
The icon turns yellow and is outlined with a white frame
T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 3T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 2 T-BERD/MTS-4000 - Getting Started Manual - PN77000002201 Rev002 - November 2015 - Copyright © 2015 4