Viega 8133.3 User manual

for barrier-free washbasins
Model Year built:
8133.3 from 03/2009
en_INT
Washbasin module
Instructions for Use

Washbasin module 2 from 13

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Standards and regulations 6
2.2 Intended use 6
2.2.1 Areas of use 6
2.3 Product description 7
2.3.1 Overview 7
2.3.2 Compatible components 7
2.3.3 Sound protection 7
2.3.4 Technical data 8
2.4 Accessories and spare parts 8
3Handling 9
3.1 Assembly information 9
3.1.1 Mounting conditions 9
3.1.2 Installation dimensions 9
3.1.3 Required tools 9
3.2 Assembly 10
3.2.1 Mounting module 10
3.2.2 Rounding off jobs 13
3.3 Disposal 13
Table of contents
Washbasin module 3 from 13

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Washbasin module 4 from 13

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand-
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Washbasin module 5 from 13

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger-
many
suitable masonry walls EN 1996-1-1
suitable concreted walls DIN 1045
suitable support profiles DIN 18183
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger-
many
Fulfilled noise protection require-
ments
DIN 4109
Fulfilled noise protection require-
ments
DIN 4109 (additional sheet 2)
Fulfilled noise protection require-
ments
VDI 4100 SSt I-SSt II
2.2 Intended use
2.2.1 Areas of use
The Viega washbasin module is suitable for mounting on wall construc-
tions pursuant to the regulations in section Ä„Regulations from section:
Fields of application / Mounting conditions“ on page 6 and is intended
for use in a Steptec pre-wall construction.
Product information
Washbasin module 6 from 13

2.3 Product description
2.3.1 Overview
Fig. 1: Components and scope of delivery
1 - washbasin module
2 - threaded bolt
3 - connections for wall plates
4 - concealed siphon
2.3.2 Compatible components
The module is compatible with all common washbasin ceramics, even
with larger projection (barrier-free).
2.3.3 Sound protection
The washbasin module complies with the noise insulation requirements
specified in section Ä„Regulations from section: Sound protection“
on page 6 .
Product information
Washbasin module 7 from 13

2.3.4 Technical data
The product has the following technical data:
drain elbow DN 40 / 50
Rubber nipple DN 40 / 30
2.4 Accessories and spare parts
The fixing set model 8173 is required to secure.
You require a concealed odour trap.
Available models
nModel 5633.1 (chrome-plated cover plate)
nModel 5633.2 (white cover plate)
The suitable drain for the following washbasin models must be ordered
from Keramag.
Keramag wash-
basin model
Paracelsus Vitalis Dejuna
Keramag model
No.
521 323 521 323 521 423
Required accessories
For Keramag washbasin models
Product information
Washbasin module 8 from 13

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
For this, observe the Steptec system instructions for use.
With the construction height, the marked height of the upper edge of
the finished floor must be observed.
3.1.2 Installation dimensions
Fig. 2: Dimensions
A - adjustable height
3.1.3 Required tools
The following tools are required for mounting the washbasin module:
Suitable walls
Construction height
Handling
Washbasin module 9 from 13

nratchet with sockets: 13 mm / 17 mm
nfork or ring spanner: 17 mm / 19 mm
nPhillips-tip screwdriver
3.2 Assembly
3.2.1 Mounting module
The two vertical rails, which surround the module, must be
open towards the module and be at an interval of 430 mm.
Secure the module onto the open Steptec rail with the slot nuts sup-
plied:
Insert the slot nut into the opening of the module.
Push the slot nut in slightly.
Turn by 90°.
ðThe slot nut is secured in the Steptec rail.
Mounting in Steptec
Securing module
Handling
Washbasin module 10 from 13

Align the height of the module.
Tighten the slot nut with a ring spanner (SW 17).
Tighten the other slot nuts in the same way.
ðThe module is secured on the rail framework.
Set desired height of the module (X). When doing so, observe the
upper edge of the finished floor.
Attach the concealed siphon with the screws attached.
Handling
Washbasin module 11 from 13

Set height of fitting connection panel.
To do this, loosen the lateral screws and choose the desired height.
Re-tighten screws.
Remove the site protection.
Check pipe position and, if necessary, set the required sizes.
Subsequent adjustment is possible.
Replace the site protection.
Attach bracket for threaded bolts:
Insert bracket horizontally and turn clockwise by 90°.
The distance between the brackets may only be a maximum of
390 mm.
Screw in threaded bolt and tighten with a ring spanner (SW 17).
Set the connections for wall plates. The interval between the con-
nections bolts can be set to 226 or 306 mm.
Handling
Washbasin module 12 from 13

Observe highest and lowest sizes.
Observe the ceramic manufacturer's instructions for additional
sizes.
3.2.2 Rounding off jobs
Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide
Aqua-KS cladding panels.
When doing so, make sure that no abutting edges converge.
Grout the abutting edges and joints with a suitable filler.
Observe the instruction manual for the cladding panels for more
information.
3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Fig. 3: Installation dimensions, concealed
siphon with ceramic
Handling
Washbasin module 13 from 13