Viega 8332.3 User manual

for tile-level installation of the WC flush plate, natural stone cov-
ering supplied by others
Model Year built:
8332.3 from 06/2009
en_INT
Functional unit
Instructions for Use

Functional unit 2 from 15

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
2.2.2 Technical data 6
3Handling 7
3.1 Assembly information 7
3.1.1 Required material and tools 7
3.2 Assembly 8
3.2.1 Mounting the functional unit 8
3.2.2 Prepare cistern 10
3.2.3 Mount flush actuation 12
3.2.4 Mounting the flush plate 13
3.3 Commissioning 14
3.3.1 Setting the flush 14
3.4 Error, faults and remedy 15
3.5 Disposal 15
Table of contents
Functional unit 3 from 15

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Functional unit 4 from 15

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand-
ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.
About these instructions for use
Functional unit 5 from 15

2 Product information
2.1 Intended use
2.1.1 Areas of use
The functional unit for natural stone panels is suitable for the tile-level
installation of flush plates with individually laid natural stone supplied
on-site.
The functional unit is suitable for concealed cisterns of the following
pre-wall systems:
nViega Steptec
nViegaswift
nViega Eco Plus
2.2 Product description
2.2.1 Overview
Fig. 1: Component overview
2.2.2 Technical data
The product has the following technical data:
Product information
Functional unit 6 from 15

3 Handling
3.1 Assembly information
3.1.1 Required material and tools
The following material is required for mounting:
nPactan cleaning agent 14
nPactan silicone adhesive 7043
nNatural stone panel
Material
Handling
Functional unit 7 from 15

3.2 Assembly
3.2.1 Mounting the functional unit
Mark the internal contour (280 x 150 mm) of the installation frame on
the cladding panel.
Use a keyhole saw to cut the cladding panel out along the dimen-
sion line.
Clad the remaining pre-wall according to the Viega specifications.
Dispose of the cover of the revision shaft.
Align the installation frame centrally over the revision shaft.
A length of double-faced adhesive tape is provided at one side of
the installation frame.
Stick the installation frame onto the cladding panel.
Adjust the chrome-plated internal frame to the respective wall cov-
ering.
The upper edge of the chrome-plated internal frame must be flush
with the wall tile.
Setting range 5–18 mm.
INFO! Make allowance for the thickness of the tile adhesive!
Handling
Functional unit 8 from 15

Shorten revision shaft flush with the chrome-plated internal frame.
INFO!
–First, cut the corners of the revision shaft.
–Then fold the sides.
Mount the cover onto the internal frame.
Have the tiler tile the pre-wall.
Handling
Functional unit 9 from 15

Fig. 2: Dimensional drawing 8332.3
Cut the natural stone coverings according to the dimensional
drawing.
Take the tolerance and thickness of the covering into consideration.
Ensure that the plastic surfaces are clean, dry, and free of grease.
Apply Pactan adhesive cleaner 14 to the plastic surfaces to which
you will attach the stone coverings – do not apply to the stone!
If applied correctly, the adhesive cleaner leaves a thin film on the
plastic surface.
Use Pactan silicone adhesive 7043 to glue the natural stone cov-
ering into the recess of the flush plate.
Allow the adhesive to cure completely.
Place the functional unit onto the basic panel.
3.2.2 Prepare cistern
The following work stages and diagrams differ depending
on the cistern being used. The relevant steps are marked
accordingly.
Handling
Functional unit 10 from 15

Requirements:
nThe cistern is fitted into the pre-wall.
nThe pre-wall is tiled.
Remove cistern cover.
Remove and keep the threaded bolts from the cistern cover.
INFO! Only for assembly of the flush plate in cistern 2H or on the
front of cistern 2L.
Press the bow backwards from the mounting of the mechanism.
INFO! Only for assembly of the flush plate on the top of cistern
2L.
Press the bow backwards from the mounting of the mechanism.
Handling
Functional unit 11 from 15

Turn the mechanism's lock by 90° in an anti-clockwise direction.
ðThe mechanism is unlocked and can be removed.
Remove and dispose of mechanism.
INFO! Only with the cistern 2H.
Remove and keep spacer.
3.2.3 Mount flush actuation
Mount Bowden cable unit
Handling
Functional unit 12 from 15

Push the Bowden cable unit onto the drain valve from the left.
The Bowden cable unit must be felt to click into place on the drain
valve.
INFO! Only with the cistern 2H.
Re-insert the spacer.
3.2.4 Mounting the flush plate
Requirements:
nThe flush actuation has been mounted.
Insert the threaded bolts left and right into the holders.
The threaded anchors must be positioned to the top and bottom.
Handling
Functional unit 13 from 15

Insert the threaded bolts so deeply that the upper edge of the
threaded bolt sticks out approx. 20 mm behind the upper edge of
the tiles.
Fasten threaded bolts with a 90° turn.
Mount Bowden cable unit onto the rear side of the basic panel.
INFO! Observe the colour of the adapter!
Screw on basic panel.
3.3 Commissioning
3.3.1 Setting the flush
20
Handling
Functional unit 14 from 15

Set the flush volume on the drain valve of the cistern.
3.4 Error, faults and remedy
Error Cause Remedy
WC does not flush Cistern is not yet completely full Wait until the cistern is sufficiently
full
No water in cistern, corner valve is
closed
Open corner valve
WC flush runs through Dirty seal in filling valve Check seal, replace if necessary
Dirty seal in drain valve Check seal, replace if necessary
WC flush actuation does not work The mechanism is not connected
to the bow
Bowden cable unit not properly
mounted on drain valve or basic
panel.
Hang the mechanism in the bow
Check the position of the Bowden
cable unit.
3.5 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Functional unit 15 from 15