WATSON Haven Perch User manual

ASSEMBLY
360.394.1300 watsonfurniture.com
V.21.0 12/2021
Haven Perch Tables

2 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Perch Table Components
Surfaces
Bridge Legs
Support Rails
Bag Hooks
Foot Bar Tubes

3 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Hardware
M6-1.0 X 12mm
(125285)
Foot Bar Connector
(0002146)
1/4 - 20 X 3.5” Bolt Tite-Joint
Connector (490006)
For two-piece surface tables only
Tools
Electric Drill T25 Torx Bit 4mm Hex Bit 13mm Wrench
M6 - 1.0 X 6mm
Cup Point Set Screw
(0002246)
M6 - 1.0 X 20mm
Flat Head Screw
(0002150)
#10 X 1” Torx Head
Screw (0002147)
3mm Hex Bit
Some steps require two people to assemble properly.

4 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Assemble Table Base
Lay out the bridge legs and support rails in the general shape of the structure,
shown below. Slide the support rails into the bridge leg brackets and secure each
end with (2) screws.
1.
M6-1.0 X 12mm
(125285)

Centerline Indicator
b.
5 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Assemble and Attach Foot Bar
Lay out the foot bar tubes ensuring all holes in the tubes are facing up. For two-surface tables, the straight tubes with tabs
should be directly across from one another with the tabs facing outward. Insert a connector (0002146) into each tube joint
and align the centerline indicator with the edge of the tube. Drive (2) set screws (0002246) per tube end to secure the
connector in place. Repeat for remaining connections (a). This step requires two people: carefully lower the assembled foot bar
into place inside the legs of the table so that the connector tabs line up with the holes in the legs. The tabs should be facing
up. Have one person hold the foot bar steady while another secures it in place. Drive one screw (0002150) through each tab to
afx the Foot Bar (b.).
2.
a.
M6 - 1.0 X 6mm
Cup Point Set
Screw (0002246)
M6 - 1.0 X 20mm
Flat Head Screw
(0002150)

6 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Connect Surfaces Together: Two-Piece Surface Tables Only
For two-piece surface tables, place surfaces upside down on a soft surface free of debris to reduce risk of damaging the
surface. Push together making sure to line up the plastic spline in the groove of each surface. Place the tite joints into the
dados in the top and tighten until the surfaces have no gap between them.
3.

7 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Attach Base to Surface
While surface is still upside down on the ground, position the base on top of the underside of the surface. Carefully align the
holes in the bridge legs with the pilot holes in the surface. All the holes may not line up at once. Line up as many as possible,
driving each screw. Leave the screws loose until all screws are in place. Flex the frame into place to align any remaining holes.
Tighten all screws to secure the base onto the surface.
4.
#10 X 1” Torx Head
Screw (0002147)

8 HAVEN PERCH TABLES ASSEMBLY INSTRUCTIONS
Attach Coat Hooks
If the table has one surface, position the coat hook centered on the underside of the surface, aligned with the pilot holes. If
the table has two surfaces, position each coat hook centered on the underside of each surface, aligned with the pilot holes.
Screw the hooks to the surface using (2) screws each.
5.
#10 X 1” Torx Head
Screw (0002147)