WB Mfg Universal Appleton User manual

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
Step 2
V032922 Version subject to change
Step 1:
• Place the top face down on a protected flat surface
so threaded inserts are facing up.
Step 2:
• With drawers taken out of base cabinet (if unit
has them), place base cabinet upside down on the
top, aligning pre-drilled holes in base cabinet with
threaded inserts in top (shown in green).
• Using a 4mm Allen wrench or 4mm hex bit, fasten
base cabinet to top with ⁄”-20x35mm joint
connector bolts.
Step 3:
• Align pre-drilled holes in leg(s) with threaded inserts
in top (shown in yellow), making sure the long side
of leg plate(s) is facing the same direction as the
front side of base cabinet.
• Using a 4mm Allen wrench or 4mm hex bit and
screw gun, fasten leg(s) to top with ⁄”-20x15mm
joint connector bolts. These bolts will be used for
either (ELS or UNET) leg(s).
Step 4:
• Remove glides from leg(s) by rotating
counterclockwise. Insert 60mm dual wheel locking
casters into leg(s). Tighten with a 14mm
open-ended wrench.
Step 5:
• Place (2) locking and (2) non-locking 75mm plate
casters on the caster base of the base cabinet,
aligning the holes in the plates with the threaded
inserts in the caster base. We recommend placing
the two locking casters towards the front end of
the cabinet. Using a 4mm Allen wrench or 4mm
hex bit, fasten casters to the caster base with
⁄”-20x25mm joint connector bolts.
Step 3
Step 5 Step 4
Before you begin, please make sure all parts and proper
quantities are included. (See Part Identifier Key) Any parts
damaged during shipment must be reported within 24 hours of
receipt. To report information regarding damages or if you have
any questions, please call 800.242.2303.
Tools Required
• 4mm Allen wrench OR
• 4mm hex bit
• Screw gun
• 14mm open-ended wrench
• Phillips head screwdriver
Universal Appleton / Appleton Desk
w/ UNET or ELS Legs
Assembly Instructions

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
Step 6a:
(Only if optional STEEL PERFORATED modesty panel
was ordered)
• Align the OPTIONAL perforated modesty panel with
the five staggered threaded inserts (shown in grey)
in the top. The modesty panel will be located towards
the back side of the base cabinet. (See image for the
correct location.) Using a 4mm Allen wrench or 4mm
hex bit and screw gun, fasten modesty panel to top
with ⁄”-20x15mm joint connector bolts.
Step 6b:
(Only if optional LAMINATE modesty panel was ordered)
• Align the OPTIONAL laminate modesty panel with the
two most inner staggered threaded inserts in the top.
The modesty panel will be located towards the back
side of the base cabinet. Attach L-brackets with pan
head Phillips screws to secure modesty panel in place.
Using (1) L-bracket, attach the end of the modesty
panel. Use (2) L-brackets to attach long side of panel
to top. (See image for the approximate location.) Use
final L-bracket to attach panel on opposite side to the
top.
Step 7:
• With the help of another person, turn desk over into
the upright position.
• Remove wire pulls from inside of base cabinet using
a Phillips head screwdriver and secure them on the
outside.
Step 8:
• If desk has drawers that were taken out in Step 2,
place them back into base cabinet.
(1) OPTIONAL laminate modesty panel
(3) L-Brackets facing front side of cabinet
(1) on opposite side
Wire pull
Step 7
Keys will be
taped inside the
cabinet
Step 6a
Step 6b
Universal Appleton / Appleton Desk
w/ UNET or ELS Legs
Assembly Instructions

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
3
Part Identifier Key
UNE-T & ELS/EJA Legs
Model #
Smooth Silver
Sku #
Black
Sku# Description Height"
UNET -EJA 04067355-G4 04067355 UNET 1.25" Sq. Adj. Jr. Leg 19 - 31
ELS -EJA 04066652-G4 04066652 ELO® 2" Straight Round Adj. Jr. Leg 20 - 33
ELS - EJAUNET -EJA
Step # Part # Description Qty.
Step 2 0406686-WO ⁄”- 20x35mm joint connector bolts 5
Step 3 Hardware
for UNET Leg
04067355-G4 (SS)
04067355 (black) UNET 1.25” Sq. Adj. Jr. Leg (UNET) 1 See UNET leg image above
04009023 ⁄”-20x15mm joint connector bolts 6
Step 3 Hardware
for ELS Legs
04066652-G4 (SS)
04066652 (black) ELO® 2” Straight Round Adj. Jr. Leg (ELS) 2 See ELS leg image above
04009023 ⁄”- 20x15mm joint connector bolts 12
Step 4 04067540 60mm dual wheel locking casters 2
Step 5
04066947 ⁄”-20x25mm joint connector bolt 16
04009656 75mm non-locking casters 2
04009658 75mm locking casters 2
Step 6a 0400951 ⁄”-20x15mm joint connector bolt 5
Step 6b
0406829 27x27x50 L-brackets 4
0400127 #10 x ⁄” black pan head Philip screws 16
Universal Appleton / Appleton Desk
w/ UNET or ELS Legs
Assembly Instructions