WE-EF ETC329-FS LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC329-FS LED
EVC329-FS LED

1
IP67, Class I, ta = 25°C
Inground Luminaire
EVC329-FSETC329-FS

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Installation Methods
Attention: The luminaire is factory-sealed and does
not need to be opened during installation.
For proper installation, use the supplied installation
blockout.
Ensure that proper drainage is provided for
the shown installation methods:
In landscape/paved areas, sand or concrete with
gravel base (Fig. I).
With fully concreted installation, drainage piping
must be provided (Fig. II).
Fig. II
Fig. I

4
Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure that proper drainage is provided for the
shown installation methods.
2) Ensure a suitable recess is provided to accommo-
date installation blockout/mounting ring assembly
B/M.
3) Test drainage (ensure water drains within 30 mins,
Warning: warranty void if luminaire installed with-
out appropriate drainage).
4) Set installation blockout/mounting ring assembly
B/M in position and ensure that:
a) Arrow Ron mounting ring Mis pointed towards
the object to be illuminated (wall, tree, column).
b) Mounting ring MLVƃXVKZLWKVXUIDFHF. If the
ƃRRUZLOOEHWLOHGRUSDYHGDIWHUZDUGVOHDYHDQ
appropriate gap.
c) Mains supply cable(s) OLVRIVXIƂFLHQWOHQJWKWR
connect sealable junction box Jwith cable Efrom
luminaire.
5) During ongoing earth and/or masonry works, do
QRWUHPRYHVWLFNHUVRQƂ[LQJWKUHDGKROHVD.
Ensure that installation blockout/mounting ring
assembly B/M is not damaged and has maintained
its original shape. If necessary use a cover plate.
6) Framing should be installed to prevent vegetation
from growing over the lens.
Phase Two
Luminaire Installation and Electrical Connection
7) Switch off mains electrical supply.
8) Check that rating shown on luminaire label conforms
with mains electrical supply.
9) Terminate cable Efrom luminaire housing Aand
mains supply cable O(for individual wiring) or
branch cable (for through wiring) in sealable junc-
tion box J– to connect cable(s). Follow the seal-
able junction box termination instruction included
in the packaging.
10)3HHORIIVWLFNHUVRQƂ[LQJWKUHDGKROHVD. Set cables
and sealable junction box Jinside installation
blockout/mounting ring assembly B/M.
11)Loosen countersunk screws C (do not turn out).
Insert mounting lever Lbetween head of counter-
sunk screws C and cover lens. Place luminaire
housing Ainto installation blockout/mounting ring
assembly B/M(Fig. IV) while aligning holes Don
mounting ring M.
Warning: When luminaire is placed inside installa-
tion blockout B, ensure there is no stress on seal-
able junction box Jor electric cables (Fig. lll).
12)Tighten countersunk screws C 'hand-tight'.

5

6
Fig. III

7
L
M
C
A
Fig. IV

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9137W0321 © WE-EF2021
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.