WE-EF FLC121 User manual

Safety Notice
The manufacturer is discharged from liability when damage
is caused by improper use or installation.
If any luminaire and/or accessory is subsequently modi-
fied, the persons responsible for the modification shall be
considered as manufacturer.
FLC100_LED_#7_020822 / 006-1079
Technical specifications are subject to change.
© WE-EF 2022
we-ef.com
WE-EF LIGHTING USA
Tel [phone]
[email protected]
WE-EF LIGHTING
Installation and
Maintenance Instructions for
Projector
FLC100 LED Series
for Mounting System RAIL66

FLC121
6.50
355˚
6.50
355˚
7.48
355˚
FLC131
FLC141
3.94
ø 1.89-2.36
ø 4.37
2.48
3.94
ø 1.89-2.36
ø 6.06
2.76
3.94
ø 1.89-2.36
ø 7.56
3.23
Floodlights for Mounting System RAIL66
IP66, IK07
Ø0.256 –0.413 in
max. 16AWG
Light Source
FLC100 .......................6-24 LED 12-48W
Nominal power, for latest data refer to
www.we-ef.com
Class I, ta = 40 °C
Weight
FLC121 ................................ 5.5 lb
FLC131 ................................ 6.8 lb
FLC141 ............................... 10.4 lb
Windage area
FLC121 ............................... 0.33 ft²
FLC131 ............................... 0.43 ft²
FLC141 ............................... 0.54 ft²
Installation
The product must be installed and maintained by
a suitably qualified professional in compliance with
latest building/construction and/or electrical regu-
lations and relevant legislation.
Attention: Switch off mains electrical supply prior
to installing and connecting the luminaire. Do not
open luminaire while mains supply is switched on.
Notice: If the luminaire is modified by anybody
other than the original manufacturer, then the
warranty will no longer be valid and shall become
the full responsibility of the modifying person/
organisation. Claims based on defects attributable
to improper installation and/or application, and the
consequences thereof, are excluded.
In case of component failure, LED replacement
due to abnormal circumstances or at end of life,
replacement must be carried out by a suitably qua-
lified and trained professional.
In case of questions please contact our technical
hotline: [phone] (from Monday - Friday
from 08.00 until 16.00 hours).
Maintenance
Apart from cleaning the product’s exterior surfaces,
no special maintenance work is required. Do not
use high-pressure cleaners.
Protect our environment: Discard used LEDs in
compliance with the most recent environmental
legislation.
120-
277 V

Installation – RAIL66 Mounting System
Prior to installing the luminaire, mount and connect
the selected RAIL66 mounting system in accordan-
ce with relevant installation instructions.
A
Y
X
3) Determine position of the luminaire Aon the
bracket X, according to the requested adjust-
ment and vicinity to the connection Y.
Installation Procedure
1) Switch off the mains electrical supply.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
12/17 IP66
FLC121 LED 120-277V / 60 Hz
145-XXXX SOE XXXXXXX
LED 3000K 12W item no. XXX
B
C
X
4) Fix clamp Bto the bracket X. Firmly tighten but-
terfly screw C.

5) Remove safety cover Zfrom the connection Y.
Insert connector assembly Gand tighten it
firmly.
Attention: In any not used connection Ythe
safety cover Zneeds to remain secure. Check
the correct position and tightness.
G
Y
Z
Y
Z
I
H
6) Loosen screws Hand Islightly. Aim luminaire in
desired direction, retighten screws Hand I.
A B C D E
Important:
In applications using lenses, make sure the light is
orientated in the direction of the object to be lit.
Please ensure that the prismatic side of the lens is
facing the LEDs.
A= Frame
B= Cover
C= Lens – IO-20, IO-180 or I0-360
D= Gasket
E= Direction of light