WE-EF QSI254 User manual

WE-EF LIGHTING
Installation and
Maintenance Instructions
Bollard
QSI254 LED
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.

1
Bollard
QSI254
Class I, ta = 40C, 6 LED / 10W
2,5 mm2 max. cross sectional area
Note : Not suitable for loop through. Grommets supplied are
suitable for single round or single flat cable
Accessories:
Planted root – Galvanised steel. kg
ESV4 for QSI254 300-0459 6.3
ESV4
ø 7 – 12 mm
(TPS) 1.5 – 2.5 mm

2
Warning: Do not open luminaire while mains supply is switched on.
[phone](from Monday - Friday from07.00 until19.00hours.
In case of questions please contact our technica lhotline:
by a suitably qualiƂed and trained professional.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
Do not use high-pressure cleaners.
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Maintenance
LED
Light Source

Installation Procedure
It is recommended to incorporate the optional planted
root ESV4 (A) to facilitate a rigid installation.
1) Switch off and isolate the mains electrical supply.
2) Check that rating shown on luminaire label con-
forms with mains electrical supply.
3) A suitable recess to be provided for planted root.
Ensure that a solid foundation as well as sufficient
mains cable length are provided.
4) Remove cover Bfrom cast base Cby releasing the
six countersunk screws D.
5) Remove the frame from the head unit by releasing
the four screws G.
6) Disconnect the LED connection cable H.
7) Remove the body of the head unit by removing the
four screws I.
8) Feed the mains supply cable J through the post E
such that the cable can reach the head unit. The
supply cable is then fed through the appropriate
compression gland (round and flat grommets
supplied) and connected to the labeled terminals L.
9) Tighten the compression gland to secure the cable.
10) Replace the body of the head unit by tightening the
four screws I, then reconnect H, then replace the
frame by tightening the four screws G.
11) Set luminaire in position and secure it by inserting
and tightening four bolts Ffirmly.
12) Reposition cover Band secure it by tightening six
countersunk screws D.
and the consequences thereof, are excluded.
cation carried out by the purchaser or third parties,
installation, application, operation and/or any modifi -
Claims based on defects attributable to improper
luminaire).
must be observed (see illustration
------m
inside
The minimum distance of an object to be illuminated
latest applicable regulations and relevant legislation.
suitably qualified p erson in c ompliance w ith the
The product must be installed and maintained by a
Installation
3

E
F
4

JG
H
I
5

WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF ILLUMINAZIONE
Italy
Tel [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapacific@we-ef. com
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
subject to change.
Technical specifications are
© WE-EF 2021
TO9139W0713 QSI254_140121_REV1