WE-EF QLS410 LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Wall Luminaires surface Mounted
QLS410 LED
QLS420 LED
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
Surge Protection
For comprehensive protection of a luminaire installation against lightning
and electrical surges, it is essential to cover mains supply and data input
lines at the distribution board level, by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation. Also, disconnect luminaires before
operating high-power devices such as, for example, electrical arc welders.

1
IP66, Class I, ta ≤40°C
QLS410 QLS420
Wall Luminaires surface Mounted

2
Light Source
LED
Maintenance
Apart from cleaning the outside of the
luminaire, no special maintenance is necessary.
Do not spray with high pressure cleaners
Installation
The product must be installed and maintained by a
suitably qualifi ed person in compliance with the latest
applicable regulations and relevant legislation.
Claims based on defects attributable to improper
installation, application, operation and/or any modi-
fi
cation carried out by the purchaser or third parties,
and the consequences thereof, are excluded.
Installation Procedure – QLS410/QLS420 LED
1. Switch off and isolate the mains electrical supply.
2. Remove wall flange Afrom cover Bby releasing
screws C.
3. Check that rating shown on luminaire label con-
forms with mains electrical supply.
4. Determine positions for two fixings crews D. Drill
relevant holes Eand insert wall plugs F.
Caution: Make sure not to damage any electric
cable, water pipe or other devices while drilling
holes.
5. Feed the mains supply cable G(and the second
cable Hfor through wiring, if required) through the
pressure screw Iat the side of the wall flange,
while setting and fixing wall flange in position.
The pre-installed packing ring His suitable for
cable diameters 7 to 9.5 mm. If the cable is bigger,
replace the pre-installed packing ring with the sup-
plied auxiliary packing ring, which is suitable for
cable diameters 9.5 to 12 mm.
6. Ensure the point arrow mark Ron the wall flange
aims upwards and that the luminaire is properly
oriented. Fix the wall flangebyinser ting and tight-
ening screws D.
7. Connect mains supply leads to respective terminals
in terminal block J(N = Neutral, L1 = Phase,
= Earthing). Tighten pressure screw(s) Ifirmly.
For the version with 1-10 V analogue dimming in-
terface, connect mains supply cable Gto respective
terminals in terminal connectors J
(N = Neutral, L1 = Phase, = Earthing) and (D+,
D–= external 1-10 V dc diming device) (Fig. II).
8. Tighten pressure screw(s) I.
9. Reposition cover Bon wall flange Aand secure in
position by evenly tightening the screws C.

3
Individual connection Through wiring

4
Fig. II Wiring diagram 1-10 V interface

1) Contents of Circular & TPS Grommet Kit. Products that
do not include a loop through option are supplied with
one kit, products with a loop through option are supplied
with two kits.
a) 1x Compression Nut
b) 1x TPS Grommet to suit 1mm2 to 2.5mm2
core cables
c) 1x Circular Grommet to suit application
(supplied with fitting)
Non-LED versions also include:
d) 3x Silicon Sleeves
2) Select the correct grommet for the application.
3) Slide the compression nut over the cable first, followed
by the grommet.
4) Feed the cable, grommet side first, into the housing, and
ensure enough cable is available to connect to the
incoming supply terminal block.
5) Tighten the compression nut to secure the cable in
place.
6) If required, remove the blanking plug and install the loop
through cabling as per steps 2 to 5.
7) For Non-LED products, strip the cable and over-sleeve
each of the cores with the high temperature sleeves. For
LED product, simply strip the cable suitable for
connection to the terminal block.
8) Connect all cores to the terminal block as labelled.
1) 2)
3) 4)
5) 6)
7) 8)
b) a) c)
d)
Installation - Cable Grommets
Circular
Flat
Circular
Flat
Sleeving required on
non-LED product only
5

www.we-ef.com
TO9116W0715 © WE-EF 2015
Technical specifications are
subject to change.
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapacifi[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST