WE-EF KTX234 User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operating high-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular socket
heads (ISO 10664). Installation requires
the use of matching tools.
WE-EF LIGHTING
Installation and Maintenance
Instructions
Bollard
KTX234 LED

1
IP66, IK10, Class I, ta = 40°C
Bollard
ESV4
Weight H lb
for KTX234 10.63 9.9
for KTY234 23.62 15.0
for KTY234 39.37 19.6
Accessories:
Planted root – Galvanised steel. lb
ESV4 for KTX234/KTY234 300-0461 9.7
KTY234
H = 23.62 in
KTX234
H = 10.63 in
KTY234
H = 39.37 in

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
To remove the head of the luminaire during maintenance,loosen screw JwithTorx T-20 tool and rotate it
anti-clockwise until it can be lifted up.
If the head of the luminaire is returned after maintenance, align it to the bollard post as shown below and
secure by tightening screw J.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOO
no longer be valid and shall become the full responsibility of the modifying person/organisation.
Claims based on defects attributable to improper installation and/or application, and the consequences
thereof, are excluded.
Attention: The luminaire is factory-sealed and does not need to be opened during installation.
The installation on site must comply with local and/or national health and safety regulations.

4
Installation Procedure
The luminaire is suitable for installation directly
on to an even surface, however it is recommended
to incorporate the provided anchor bolts or optional
planted root to ensure maximum stability.
Installation – KTX
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
2) Check that rating shown on luminaire label conforms
with mains electrical supply.
3) (if using planted root mounting accessory)
A suitable recess to be provided for planted root A.
(QVXUHWKDWDVROLGIRXQGDWLRQDVZHOODVVXĩFLHQW
mains cable length are provided.
Note: Planted root installation instruction is
available at the end of this document.
4) Remove head of luminaire Hfrom bollard post
Bafter loosening screw JwithTorx T-20 tool and
rotating it anti-clockwise until it can be lifted up.
5) Set bollard post Bin position and secure by insert-
ing and tightening provided mounting fasteners I.
The direction of light for KTX [R65] is opposite the
set screw J.
6) Connect luminaire cable Eto mains supply cable F
in watertight terminal connector G(not supplied by
WE-EF):
a) ON/OFF (L = Phase, N = Neutral, = Earthing)
b) 0-10V (L = Phase,N = Neutral, = Earthing,
D-/D+ = 0-10V control line).
7) Place watertight terminal connector Gand excess
cable inside bollard post B.
8) Return head of luminaire Hto bollard post Band
secure by tightening screw J.

5
KTX234

6
Direction of Light for [R65] One-sided
set screw
Torque:
Screw Torque
M4 max. 2.0 Nm (17.7 in-lb)
M5 max 4.0 Nm (35.4 in-lb)
M6 max 6.0 Nm (53.1 in-lb)
M8 max. 15.0 Nm (132.8 in-lb)
M16 max. 100.0 Nm (885.1 in-lb)

7
www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9241W0422 © WE-EF 2022
Technical specifications are
subject to change.

WE-EF LIGHTING
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2
ESV6

2
Planted Root
ESV4 300-0461
ESV4 300-0586
ESV4 300-0464
ESV4 300-0459
Suitability
1. KTX234
2. KTY234
3. ZFY230
4. GRY224
5. Short post
Suitability
1. XRY334
2. XRZ334
3. RRY334
4. RRZ334
Suitability
1. CFY259
2. GRY234
3. RRY324
4. RRZ324
5.XRY324
6.XRZ324
Suitability
1. QSI254

3
Planted Root
ESV2 300-9115
ESV6 300-0824
ESV6 300-0457
Suitability
1. PSY414/424
Suitability
1.AML-C
2. FLA461
Suitability
1. LTM440
2. LTM444
3.AMW-C
4.AMF-C
5.AMF-S
6.AML-C

4
Installation Instruction
1) Note: It is the responsibility to installer to
ensure the suitability of the ESV planted root
for any local or national structural requirements
for installation,and that planted root is suitable
IRUVLWHVSHFLĥFFRQGLWLRQV
Instructions are a guideline for installation to
these requirements and provide detail for
installation orientation and mounting details.
4) For ESV2 please orientate planted root as
shown (base plate is parallel to the pathway).
For this installation, use M12 bolts supplied.
2) Please note,ESV4 and ESV6 must be
RULHQWDWHGFRUUHFWO\IRUGLĪHUHQWSURGXFWV
In both instances conduit entry can be rotated
to match cable routing.
When the ESV is being installed for following
products: KTY234/KTX234/ZFY230/CFY259/
FLA461, please orientate the planted root
as shown (base plate is at an angle of 45°
to the pathway). For this installation,
use the M8 bolts supplied.
3) For all other product that use ESV4 please
orientate planted root as shown (base plate is
parallel to the pathway).For this installation,
use M8 bolts supplied.

5
 2ULHQWDWH(69DVUHTXLUHGDQGĥWHOHFWULFDO
connections/conduit.
5) For all other product that use ESV6 please
orientate planted root as shown (base plate
is parallel to the pathway).For this installation,
use M16 bolts supplie.
7) Place the ESVin the form work for concrete
pad, ensuring orientation, position and levels
are correct. Ensure all openings on ESV are
EODQNHGRĪLQFOXGLQJPRXQWLQJSODWHKROH
8) Fit the nominated bolts through mounting
ĦDQJH(QVXUHVHYHUDOWKUHDGVIHHGWKURXJK
 WKHSODWHDQGWDSHRĪWRSDQGERWWRP%ROWV
DUHLQVHUWHGWRSURWHFWWKUHDGVRĪSODWHDQG
QHHGWREHUHPRYHGIRUĥWWLQJLQVWDOODWLRQ
after setting the ESV.

6
9) Pour concrete to desired level depending on
requirement of concrete, paver or soil. Ensure
WKDWIRUDQ\LQVWDOODWLRQPRXQWLQJĦDQJHPXVW
EHĦXVKRUKLJKHUWKDQVXUURXQGLQJVXUIDFH
level.
$IWHUFRQFUHWHKDVFXUHGIRUVSHFLĥHGWLPH
UHPRYHEODQNLQJDQGEROWV,QVWDOOĥWWLQJ
(as per luminaire instructions) onto mounting
ĦDQJH
Concrete
Paver
Soil

www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9257W0422 © WE-EF 2022
Technical specifications are
subject to change.