WIL-RICH 2510 User manual

WIL-RICH
2510/2530 CHISEL PLOW
ASSEMBLY/OPERATORS
MANUAL
WIL-RICH
PO Box 1030
Wahpeton, ND 58074
PH [phone]
Fax [phone]
www.wil-rich.com

WARRANTY
The only warranty Wil-Rich gives and the only warranty the dealer is authorized to give is as follows:
We warrant products sold by us to be in accordance with our published specifications or those
specifications agreed to by us in writing at time of sale. Our obligation and liability under this warranty
is expressly limited to repairing, or replacing, at our option, within 12 months after date of retail delivery,
any product not meeting the specifications. We make no other warranty, express or implied and
make no warranty of merchantability or of fitness for any particular purpose. Our obligation
under the warranty shall not include any transportation charges or costs or installation or any liability for
direct, indirect or consequential damage or delay. If requested by us, products or parts for which a
warranty claim is made are to be returned transportation prepaid to our factory. Any improper use,
operation beyond rated capacity, substitution of parts not approved by us, or any alteration or repair by
others in such manner as in our judgment affects the product materially and adversely shall void this
warranty. No employee or representative is authorized to change this warranty in any way or
grant any other warranty.
Wil-Rich reserves the right to make improvement changes on any of our products without notice.
When warranty limited or not applicable: Warranty on hoses, cylinders, hubs, spindles, engines,
valves, pumps or other trade accessories are limited to the warranties made by the respective
manufactures of these components. Rubber tires and tubes are warranted directly by the respective
tire manufacturer only, and not by Wil-Rich.
Warranty does not apply to any machine or part which has been repaired or altered in any way so as in
the our judgment to affect its reliability, or which has been subject to misuse, negligence or accident.
AWarranty Validation and Delivery Report Form must be filled out and received by Wil-Rich to
initiate the warranty coverage.
WARRANTY CLAIMS PROCEDURE
1. The warranty form must be returned to Wil-Rich within fifteen (15) working days from the repair date.
2. Parts returned to Wil-Rich without authorization will be refused. The parts must be retained at the
dealership for ninety (90) days after the claim has been filed. If the Service Department would like to
inspect the parts, a packing slip will be mailed to the dealer. The packing slip must be returned with the
parts. The parts must be returned prepaid within thirty (30) days of receiving authorization. After the
parts are inspected and warranty is verified, credit for the return freight will be issued to the dealer.
3. Parts that will be scrapped at the dealership will be inspected by a Wil-Rich Sales Representative,
District Sales Manager or Service Representative within the ninety (90) day retaining period.

Chisel Plough
1 Safety .....................................................................7
1.1 Introduction .........................................................9
1.1.1 Safety alert symbol ................................................9
1.1.2 Safety messages ..................................................9
1.1.3 Informational messages .............................................9
1.1.4 Safety signs ......................................................9
1.1.5 A word to the operator .............................................10
1.1.6 This manual .....................................................11
1.2 Operation ..........................................................12
1.2.1 Prepare for operation ..............................................12
1.2.2 Personal protective equipment .......................................12
1.2.3 Agricultural chemicals .............................................12
1.2.4 Travel on public roads ..............................................13
1.3 Maintenance .......................................................15
1.3.1 Fire prevention and first aid .........................................15
1.3.2 High pressure leaks ...............................................16
1.3.3 Tire safety ......................................................16
1.3.4 Replacement parts ................................................17
1.4 Transport locks .....................................................18
1.5 Marker lamps ......................................................19
1.6 Safety sign location .................................................20
2 Introduction ..............................................................27
2.1 Introduction ........................................................29
2.1.1 Intended use ....................................................29
2.1.2 Proper disposal of waste ...........................................29
2.2 Machine identification ..............................................30
2.2.1 Serial number plate location .........................................30
2.2.2 Serial number description ...........................................30
2.3 Chisel plough ......................................................32
2.3.1 Level-lift hitch ...................................................32
2.3.2 Floating hitch ....................................................32
2.4 Major components .................................................33
2.5 Operator manual storage ...........................................34
3 Operation .................................................................35
3.1 Bleeding air from the hydraulic lift system ...........................37
3.2 Bleeding air from the hydraulic fold system ..........................38
3.3 Connecting the machine to the tractor ...............................39
3.4 Disconnecting the machine from the tractor ..........................41
3.5 Preparing the machine for transport .................................42
3.6 Preparing the machine for field operation ............................43
3.7 Beginning field operation ...........................................44
3.7.1 Items to check after first operation ....................................44
3.8 Leveling the machine ...............................................45
3.8.1 Leveling a machine with the level-lift hitch front to rear .....................45
3.8.2 Leveling a machine with the floating hitch front to rear ......................45
3.8.3 Leveling the wings to the center frame .................................46
Table of contents
Chisel Plough
9971422WRA

3.9 Adjusting the gauge wheels .........................................48
3.9.1 Adjusting the gauge wheels - ratchet adjust ..............................48
3.9.2 Adjusting the gauge wheels - hydraulic .................................48
3.10 Operating depth ...................................................50
3.10.1 Single point depth control ..........................................50
3.11 Spring shanks .....................................................51
4 Maintenance ..............................................................53
4.1 Lubrication and maintenance chart ..................................55
4.2 Lubrication fitting locations .........................................56
4.3 Servicing the wheel bearings ........................................58
4.4 Servicing the tandem pivot bearings .................................59
4.5 Storage ............................................................60
4.5.1 Preparing the machine for storage ....................................60
4.5.2 Preventing corrosion of extended hydraulic cylinders .......................61
4.5.3 Removing the machine from storage ...................................61
5 Troubleshooting ..........................................................63
5.1 Troubleshooting ....................................................65
6 Specifications .............................................................67
6.1 Specifications ......................................................69
6.2 Transport dimensions ...............................................71
6.3 Minimum tow vehicle weight .......................................72
6.4 Maximum transport speed ..........................................73
6.5 Lubrication specifications ...........................................74
6.6 Tire air pressure ....................................................75
7 Assembly .................................................................77
7.1 Preparing for assembly .............................................81
7.1.1 Service parts ....................................................81
7.2 Assembling the center frame ........................................82
7.2.1 Installing the center lift .............................................83
7.2.2 Installing the center lift hubs and wheels ................................84
7.2.3 Installing the center frame mast tubes .................................85
7.2.4 Installing the 19 to 29 ft fold anchors ...................................86
7.2.5 Installing the 31 to 47 ft fold anchors ...................................87
7.2.6 Installing the 19 to 29 ft wing rests ....................................88
7.2.7 Installing the 31 to 47 ft wing rest .....................................89
7.3 Assembling the tongue .............................................90
7.3.1 Installing the 13 to 29 ft tongue ......................................90
7.3.2 Installing the 31 to 47 ft tongue ......................................91
7.3.3 Installing the utility pole ............................................92
7.4 Installing the shank extension .......................................93
7.5 Installing the center frame shanks ...................................94
7.5.1 Installing the 650 lb shanks ..........................................94
7.5.2 Installing the 1000 lb shanks .........................................95
7.6 Installing the wings .................................................96
7.6.1 Mounting the 19 to 23 ft wing frame hinges .............................96
7.6.2 Installing the 19 to 23 ft wing frames - 3 ft wing ..........................97
7.6.3 Mounting the 25 to 29 ft wing frame hinges .............................98
7.6.4 Installing the 25 to 29 ft wing frames - 6 ft wing ..........................99
7.6.5 Mounting the 31 to 47 ft wing frame hinges ............................ 101
7.6.6 Installing the 31 to 41 ft wing frames - 9 ft wing ......................... 102
Table of contents
Chisel Plough
9971422WRA

7.6.7 Installing the 37 to 47 ft wing frames - 12 ft wing .........................103
7.6.8 Mounting the 31 to 47 ft outer wing frame hinges ........................ 104
7.6.9 Installing the 31 to 47 ft outer wing frames - 3 ft wing ..................... 105
7.7 Installing the wing frame shanks ................................... 106
7.7.1 Installing the 650 lb shanks .........................................106
7.7.2 Installing the 1000 lb shanks ........................................107
7.8 Installing the wing lifts .............................................108
7.8.1 Installing the wing lift hubs and wheels ................................109
7.9 Mounting the front lift tube ........................................ 110
7.10 Mounting the rear lift tube ........................................ 111
7.11 Installing the frame tie straps ..................................... 112
7.11.1 Installing the 31 to 47 ft center frame strap - level lift hitch .................112
7.11.2 Installing the 37 to 47 ft inner wing frame strap ......................... 113
7.12 Installing the 37 to 47 ft outer wing rest ............................114
7.13 Installing the fold brackets ........................................ 115
7.13.1 Mounting the 31 to 41 ft wing fold brackets - 9 ft wing ....................115
7.13.2 Mounting the 37 to 47 ft wing fold brackets - 12 ft wing ...................116
7.14 Installing the wing mast tubes .................................... 117
7.15 Installing the stroke control assembly ............................. 118
7.15.1 Mounting the stroke control valve ...................................118
7.15.2 Mounting the front of the stroke control .............................. 119
7.15.3 Mounting the rear of the stroke control ............................... 120
7.16 Installing the ratchet adjust gauge wheels ......................... 121
7.16.1 Installing the gauge wheel mount - ratchet adjust ........................121
7.16.2 Installing the gauge wheel jack and arms - ratchet adjust .................. 122
7.16.3 Assembling the gauge wheel pivot bracket - ratchet adjust .................123
7.16.4 Fastening the gauge wheel pivot bracket to the arms - ratchet adjust ......... 124
7.16.5 Installing the gauge wheel hubs and wheels - ratchet adjust ................125
7.17 Installing the hydraulic gauge wheels ..............................126
7.17.1 Installing the center frame gauge wheel mount - hydraulic ................. 126
7.17.2 Installing the center frame gauge wheel linkage - hydraulic .................127
7.17.3 Assembling the center frame gauge wheel axle - hydraulic .................128
7.17.4 Installing the center frame gauge wheel axle - hydraulic ................... 129
7.17.5 Installing the wing frame gauge wheel mount - hydraulic .................. 130
7.17.6 Installing the wing frame gauge wheel linkages - hydraulic ................. 131
7.17.7 Assembling the wing frame gauge wheel axle - hydraulic ..................132
7.17.8 Installing the wing frame gauge wheel axle assembly - hydraulic .............133
7.17.9 Installing the gauge wheel hubs and wheels - hydraulic ................... 134
7.17.10 Installing the gauge wheel lift tubes - hydraulic .........................135
7.18 Installing the marker lamps ....................................... 136
7.18.1 Installing the marker lamp harness .................................. 137
7.19 Installing the rear tow hitch .......................................138
7.20 Installing the hydraulics ...........................................140
7.20.1 Installing the center lift cylinders ....................................140
7.20.2 Installing the wing lift cylinders .....................................141
7.20.3 Installing the 19 to 23 ft lift hydraulics ................................ 142
7.20.4 Installing the 25 to 29 ft lift hydraulics ................................ 144
7.20.5 Installing the 31 to 41 ft lift hydraulics ................................ 146
7.20.6 Installing the 37 to 47 ft lift hydraulics ................................ 148
7.20.7 Installing the 19 to 29 ft fold cylinders ................................149
7.20.8 Installing the 31 to 47 ft center fold cylinders ...........................150
7.20.9 Installing the 31 to 47 ft outer fold cylinders ............................151
7.20.10 Installing the 19 to 29 ft fold hydraulics .............................. 152
7.20.11 Installing the 31 to 39 ft fold hydraulics - no outer wing ...................154
7.20.12 Installing the 37 to 47 ft fold hydraulics - with outer wing ................. 156
Table of contents
Chisel Plough
9971422WRA

7.21 Shank locations - 12 inch spacing ..................................158
7.21.1 13 ft shank locations - 12 inch spacing ................................158
7.21.2 15 ft shank locations - 12 inch spacing ................................160
7.21.3 17 ft shank locations - 12 inch spacing ................................162
7.21.4 19 ft shank locations - 12 inch spacing ................................164
7.21.5 21 ft shank locations - 12 inch spacing ................................166
7.21.6 23 ft shank locations - 12 inch spacing ................................168
7.21.7 25 ft shank locations - 12 inch spacing ................................170
7.21.8 27 ft shank locations - 12 inch spacing ................................172
7.21.9 29 ft shank locations - 12 inch spacing ................................174
7.21.10 31 ft shank locations - 12 inch spacing ...............................176
7.21.11 33 ft shank locations - 12 inch spacing ...............................178
7.21.12 35 ft shank locations - 12 inch spacing ...............................180
7.21.13 37 ft shank locations - 9 ft wing - 12 inch spacing .......................182
7.21.14 37 ft shank locations - 12 ft wing - 12 inch spacing ......................184
7.21.15 39 ft shank locations - 9 ft wing - 12 inch spacing .......................186
7.21.16 39 ft shank locations - 12 ft wing - 12 inch spacing ......................188
7.21.17 41 ft shank locations - 12 inch spacing ...............................190
7.21.18 43 ft shank locations - 12 inch spacing ...............................192
7.21.19 45 ft shank locations - 12 inch spacing ...............................194
7.21.20 47 ft shank locations - 12 inch spacing ...............................196
7.22 Shank locations - 15 inch spacing ..................................198
7.22.1 13 ft shank locations - 15 inch spacing ................................198
7.22.2 15 ft shank locations - 15 inch spacing ................................200
7.22.3 17 ft shank locations - 15 inch spacing ................................202
7.22.4 19 ft shank locations - 15 inch spacing ................................204
7.22.5 21 ft shank locations - 15 inch spacing ................................206
7.22.6 23 ft shank locations - 15 inch spacing ................................208
7.22.7 25 ft shank locations - 15 inch spacing ................................210
7.22.8 27 ft shank locations - 15 inch spacing ................................212
7.22.9 29 ft shank locations - 15 inch spacing ................................214
7.22.10 31 ft shank locations - 15 inch spacing ...............................216
7.22.11 33 ft shank locations - 15 inch spacing ...............................218
7.22.12 35 ft shank locations - 15 inch spacing ...............................220
7.22.13 37 ft shank locations - 9 ft wing - 15 inch spacing .......................222
7.22.14 37 ft shank locations - 12 ft wing - 15 inch spacing ......................224
7.22.15 39 ft shank locations - 9 ft wing - 15 inch spacing .......................226
7.22.16 39 ft shank locations - 12 ft wing - 15 inch spacing ......................228
7.22.17 41 ft shank locations - 15 inch spacing ...............................230
7.22.18 43 ft shank locations - 15 inch spacing ...............................232
7.22.19 45 ft shank locations - 15 inch spacing ...............................234
7.22.20 47 ft shank locations - 15 inch spacing ...............................236
8 Index ....................................................................239
Table of contents
Chisel Plough
9971422WRA

1. Safety
1.1 Introduction ..............................................................9
1.1.1 Safety alert symbol .....................................................9
1.1.2 Safety messages .......................................................9
1.1.3 Informational messages ..................................................9
1.1.4 Safety signs ...........................................................9
1.1.5 A word to the operator ..................................................10
1.1.6 This manual ..........................................................11
1.2 Operation ...............................................................12
1.2.1 Prepare for operation ...................................................12
1.2.2 Personal protective equipment ............................................12
1.2.3 Agricultural chemicals ..................................................12
1.2.4 Travel on public roads ...................................................13
1.3 Maintenance ............................................................15
1.3.1 Fire prevention and first aid ..............................................15
1.3.2 High pressure leaks ....................................................16
1.3.3 Tire safety ...........................................................16
1.3.4 Replacement parts .....................................................17
1.4 Transport locks ..........................................................18
1.5 Marker lamps ...........................................................19
1.6 Safety sign location ......................................................20
Table of contents
Chisel Plough 7
9971422WRA

Table of contents
8 Chisel Plough
9971422WRA

1.1 Introduction
1.1.1 Safety alert symbol
The safety alert symbol means Attention! Become
Alert! Your Safety Is Involved!
Look for the safety alert symbol both in this
manual and on safety signs on this machine. The
safety alert symbol will direct your attention to
information that involves your safety and the
safety of others.
Fig. 1
1.1.2 Safety messages
The words DANGER, WARNING or CAUTION are
used with the safety alert symbol. Learn to
recognize these safety alerts and follow the
recommended precautions and safety practices.
DANGER:
Indicates an imminently hazardous
situation that, if not avoided, will
result in DEATH OR VERY SERIOUS
INJURY.
WARNING:
Indicates a potentially hazardous
situation that, if not avoided, could
result in DEATH OR SERIOUS
INJURY.
CAUTION:
Indicates a potentially hazardous
situation that, if not avoided, may
result in MINOR INJURY.
Fig. 2
1.1.3 Informational messages
The words important and note are not related to personal safety, but are used to give additional
information and tips for operating or servicing this equipment.
IMPORTANT: Identifies special instructions or procedures which, if not strictly observed, could result in
damage to or destruction of the machine, process, or its surroundings
NOTE: Identifies points of particular interest for more efficient and convenient repair or operation.
1.1.4 Safety signs
WARNING:
Do not remove or obscure safety signs. Replace any safety signs that are not readable or
are missing. Replacement signs are available from your dealer in the event of loss or
damage. The actual location of the safety signs is illustrated at the end of this section.
Keep signs clean by wiping off regularly. Use a mild soap and water solution if necessary.
1. Safety
Chisel Plough 9
9971422WRA

If parts have been replaced or a used machine has been purchased, make sure all safety signs are present
and in the correct location and can be read. Illustrations of safety sign locations are located at the rear of
this section.
Replace any safety signs that can not be read, are damaged, or are missing. Clean the machine surface
thoroughly with a mild soap and water solution before replacing signs. Replacement safety signs are
available from your dealer.
1.1.5 A word to the operator
It is your responsibility to read and understand the
safety section in this manual and the manual for all
attachments before operating this machine.
Remember you are the key to safety. Good safety
practices not only protect you, but also the people
around you.
Study the content in this manual and make the
content a working part of your safety program.
Keep in mind that this safety section is written
only for this type of machine. Practice all other
usual and customary safe working precautions,
and above all remember - safety is your
responsibility. You can prevent serious injury or
death.
This safety section is intended to point out some
of the basic safety situations that may be
encountered during the normal operation and
maintenance of your machine. This section also
suggests possible ways of dealing with these
situations. This section is not a replacement for
other safety practices featured in other sections of
this manual.
Personal injury or death may result if these
precautions are not followed.
Learn how to operate the machine and how to use
the controls properly.
Do not let anyone operate the machine without
instruction and training.
For your personal safety and the personal safety of
others, follow all safety precautions and
instructions found in the manuals and on safety
signs affixed to the machine and all attachments.
Use only approved attachments and equipment.
Make sure your machine has the correct
equipment needed by the local regulations.
WARNING:
An operator should not use alcohol or
drugs which can affect their alertness
or coordination. An operator on
prescription or 'over the counter'
drugs needs medical advice on
whether or not they can properly
operate machines.
Fig. 3
1. Safety
10 Chisel Plough
9971422WRA

CAUTION:
If any attachments used on this
equipment have a separate Operator
Manual, see that manual for other
important safety information.
1.1.6 This manual
This manual covers general safety practices for this machine. The operator manual must always be kept
with the machine.
Right-hand and left-hand, as used in this manual, are determined by facing the direction the machine will
travel when in use.
The photos, illustrations, and data used in this manual were current at the time of printing, but due to
possible in-line production changes, your machine can vary slightly in detail. The manufacturer reserves the
right to redesign and change the machine as necessary without notification.
WARNING:
In some of the illustrations and photos used in this manual, shields or guards may have
been removed for clarity. Never operate the machine with any shields or guards removed.
If the removal of shields or guards is necessary to make a repair, they must be replaced
before operation.
1. Safety
Chisel Plough 11
9971422WRA

1.2 Operation
1.2.1 Prepare for operation
Read and understand all operating instructions and precautions in this manual before operating or servicing
the machine.
Make sure you know and understand the positions and operations of all controls. Make certain all controls
are in neutral and the parking brake is applied before starting the machine.
Make certain all people are well away from your area of work before starting and operating the machine.
Check and learn all controls in an area clear of people and obstacles before starting your work. Be aware of
the machine size and have enough space available to allow for operation. Never operate the machine at
high speeds in crowded places.
Emphasize the importance of using correct procedures when working around and operating the machine.
Do not let children or unqualified persons operate the machine. Keep others, especially children, away
from your area of work. Do not permit others to ride on the machine.
Make sure the machine is in the proper operating condition as stated in the Operator Manual. Make sure
the machine has the correct equipment required by local regulations.
1.2.2 Personal protective equipment
Wear all personal protective equipment (PPE) and
protective clothing issued to you or called for by
job conditions and country/local regulations. PPE
includes, but is not limited to, equipment to
protect eyes, lungs, ears, head, hands and feet
when operating, servicing, or repairing equipment.
Always keep hands, feet, hair, and clothing away
from moving parts. Do not wear loose clothing,
jewelry, watches, or other items that could
entangle in moving parts. Tie up long hair that can
also entangle in moving parts.
Fig. 4
1.2.3 Agricultural chemicals
Agricultural chemicals can be very hazardous. Improper use of fertilizer, fungicides, herbicides, insecticides
and pesticides can injure people, plants, animals, soil and other people's property.
Always read and follow all manufacturers' instructions before opening any chemical container.
Even if you think you know the instructions, read and follow instructions each time you use a chemical.
Use the same precautions when adjusting, servicing, cleaning or storing the machine as used when
installing chemicals into the hoppers or tanks.
Inform anyone who comes in contact with chemicals of the potential hazards involved and the safety
precautions required.
Stand upwind and away from smoke from a chemical fire.
Store or dispose of all unused chemicals only in a manner as specified by the chemical manufacturer.
1. Safety
12 Chisel Plough
9971422WRA

1.2.4 Travel on public roads
Make sure you understand the speed, brakes,
steering, stability, and load characteristics of this
machine before you travel on public roads.
Use good judgment when traveling on public
roads. Maintain complete control of the machine at
all times. Never coast down hills.
The maximum speed of farm equipment is
governed by local regulations. Adjust travel speed
to maintain control at all times.
Familiarize yourself with and obey all road
regulations that apply to your machine. Consult
your local law enforcement agency for local
regulations regarding movement of farm
equipment on public roads. Use head lamps,
flashing warning lamps, tail lamps and turn signals,
day and night, unless prohibited by local law.
Make sure all the flashers are operating prior to
driving on the road. Make sure reflectors are
correctly installed, in good condition, and wiped
clean. Make sure the Slow Moving Vehicle (SMV)
emblem is clean, visible, and correctly mounted on
the rear of the machine.
Always travel with the loader as low as possible.
Do not drive with loader up.
Lock brake pedals together (if equipped with dual
brake pedals) so both wheel brakes will be applied
at the same time.
Raise implements to transport position and lock in
place. Place all implements into narrowest
transport configuration.
Disengage the power takeoff and differential lock.
With towed implements, use a proper hitch pin
with a clip retainer and safety transport chain.
Be aware of other traffic on the road. Keep well
over to your own side of the road and pull over,
whenever possible, to let faster traffic pass.
Be aware of the overall width, length, height, and
weight of the machine. Be careful when
transporting the machine on narrow roads and
across narrow bridges.
Fig. 5
1. Safety
Chisel Plough 13
9971422WRA

Watch for overhead wires and other obstructions.
Avoid contact with electrical power lines. Contact
with electrical power lines can cause electrical
shock, resulting in very serious injury or death.
Fig. 6
1. Safety
14 Chisel Plough
9971422WRA

1.3 Maintenance
1.3.1 Fire prevention and first aid
Be prepared for emergencies.
Keep a first aid kit handy for treatment of minor
cuts and scratches.
Always carry one or more fire extinguishers of the
correct type. Check fire extinguishers regularly as
instructed by the manufacturer. Make sure fire
extinguishers are properly charged and in
operating condition.
Due to the nature of the crops this machine will
operate in, the risk of fire is of concern. Use a
water type fire extinguisher or other water source
for a fire in crop.
For fires involving anything other than crop, such
as oil or electrical components, use a dry chemical
fire extinguisher with an ABC rating.
Mount fire extinguishers within easy reach of
where fires can occur.
Frequently remove accumulated crop material
from the machine and check for overheated
components. Check the machine daily for any
noises that are not normal. Such noises could
indicate a failed component that can cause excess
heat.
If any flame cutting, welding, or arc welding is to
be done on the machine or attachments, make
sure to clear any crop material or debris from
around the area. Make sure the area below the
work area is clear of any flammable material as
falling molten metal or sparks can ignite the
material.
Fig. 7
If fire occurs stand upwind and away from smoke
from the fire.
Fig. 8
1. Safety
Chisel Plough 15
9971422WRA

1.3.2 High pressure leaks
Fluid leaking from the hydraulic system or the fuel
injection system under high pressure can be very
hard to see. The fluid can go into the skin causing
serious injury.
Fluid injected into the skin must be surgically
removed within a few hours. If not removed
immediately, serious infection or reaction can
develop. Go immediately to a doctor who knows
about this type of injury.
Fig. 9
Use a piece of cardboard or wood to search for
possible leaks. Do not use your bare hand. Wear
leather gloves for hand protection and safety
goggles for eye protection.
Relieve all pressure before loosening any hydraulic
lines. Relieve the pressure by lowering raised
equipment, shutting off accumulator valve, if
equipped, and shutting off the engine. Tighten all
connections securely before applying pressure.
Fig. 10
1.3.3 Tire safety
Check tires for cuts, bulges, and correct pressure.
Replace worn or damaged tires. When tire service
is needed, have a qualified tire mechanic service
the tire. Tire changing can be very hazardous and
must be done by qualified tire mechanic using
proper tools and equipment. See the
Specifications Section for the correct tire size.
Tire explosion and/or serious injury can result from
over inflation. Do not exceed the tire inflation
pressures. See the Specifications Section for the
correct tire pressure.
Do not inflate a tire that is seriously under inflated
or has been run flat. Have the tire checked by
qualified tire mechanic.
Do not weld on the rim when a tire is installed.
Welding will make an air/gas mixture that can
cause an explosion and burn with high
temperatures. This danger applies to all tires,
inflated or deflated. Removing air or breaking the
bead is not enough. The tire must be completely
removed from the rim prior to welding.
Fig. 11
1. Safety
16 Chisel Plough
9971422WRA

When preparing a calcium chloride solution for
fluid ballasting the tractor tires, never pour water
onto the calcium chloride. A chlorine gas can be
generated which is poisonous and explosive. This
can be avoided by slowly adding calcium chloride
flakes to water and stirring until they are dissolved.
When seating tire beads onto rims, never exceed
2.4 bar (35 psi) or the maximum inflation pressure
specified on the tire. Inflation beyond this
maximum pressure may break the bead, or even
the rim, with explosive force.
1.3.4 Replacement parts
Where replacement parts are necessary for
periodic maintenance and servicing, genuine
replacement parts must be used to restore your
equipment to original specifications.
The manufacturer will not accept responsibility for
installation of unapproved parts and/or accessories
and damages as a result of their usage.
Fig. 12
1. Safety
Chisel Plough 17
9971422WRA

1.4 Transport locks
The machine is equipped with transport locks. Use
the transport locks in the operating position (1)
when moving the machine on roads. When not in
use, keep the transport locks in the storage
position (2).
Fig. 13
1. Safety
18 Chisel Plough
9971422WRA

1.5 Marker lamps
The machine has marker lamps that must be used
when moving the machine on roads.
The machine is equipped with two red lamps (1)
located toward the rear center of the machine.
The machine is equipped with two amber lamps
(2) located at the outside edges of the folded
machine.
Fig. 14
1. Safety
Chisel Plough 19
9971422WRA

1.6 Safety sign location
The following safety signs are installed on the machine.
Fig. 15
Item Description
1 Danger / folding wings
2 Warning / lockout
3 Caution / safety chains
4 Warning / negative tongue weight
5 Warning / remove key
6 Warning / read Operator Manual
7 Danger / high line
8 Warning / hydraulic fluid pressure
9 Maximum speed
10 Reflector / yellow
11 Reflector / red
1. Safety
20 Chisel Plough
9971422WRA