WIL-RICH PT2200 FWD User manual

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
1
PT2200 FWD
PLANTER BAR
OPERATOR'S MANUAL
WIL-RICH
Printed in USA
(74277) WR-12/10
PO BOX 1030
Wahpeton, ND 58075
Ph 701-642-2621
Fax [phone]
WWW.WIL-RICH.COM
ASSEMBLY, OPERATOR & PART'S

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 2
WIL-RICH, LLC
WARRANTY
Wil-Rich’s products are warranted to the original non-
commercial purchaser to be free from defects in material and
workmanship for a minimum period of twelve (12) months from the original date of purchase.
Additional Field Cultivator Warranty: Wil-Rich warrants to the original purchaser of each new Wil-Rich Field Culti-
vator unit (Excel and QuadX), and Disk Field Cultivators that the product be free from defects in material and work-
manship for the period of three (3) years on the main frames and shank assemblies. All other components are
covered by the twelve (12) month warranty period.
Commercial Use: Warranty for commercial, rental or custom use of any Wil-Rich product is limited to 90 days,
parts and labor.
We warrant products sold by us to be in accordance with our published specifications or those specifications
agreed to by us in writing at time of sale. Our obligation and liability under this warranty is expressly limited to re-
pairing, or replacing, at our option, within 12 months after date of retail delivery, any product not meeting the speci-
fications. We make no other warranty, express or implied and make no warranty of merchantability or of
fitness for any particular purpose. If requested by us, products or parts for which a warranty claim is made are
to be returned transportation prepaid to our factory. Any improper use, operation beyond rated capacity, substitu-
tion of parts not approved by us, or any alteration or repair by others in such manner as in our judgment affects the
product materially and adversely shall void this warranty. No employee or representative is authorized to
change this warranty in any way or grant any other warranty.
Wil-Rich reserves the right to make improvement changes on any of our products without notice.
When warranty limited or not applicable: Warranty on hydraulic hoses, hydraulic cylinders, hubs, spindles, en-
gines, valves, pumps or other trade accessories are limited to the warranties made by the respective manufactures
of these components. Rubber tires and tubes are warranted directly by the respective tire manufacturer only, and
not by Wil-Rich.
This warranty shall not be interpreted to render Wil-Rich liable for injury or damages of any kind or nature to per-
son or property. This warranty does not include claims for, or extend to the loss or damage of crops, loss because
of delay in seeding/planting or harvesting, or any expense or loss incurred for labor, substitute machinery, rental,
and transportation expense or for any other reason.
A Warranty Validation and Delivery Report Form must be filled out and received by Wil-Rich to initiate the
warranty coverage.
WARRANTY CLAIMS PROCEDURE
1. The warranty form must be returned to Wil-Rich within thirty (30) working days from the repair date.
2. Parts returned to Wil-Rich without authorization will be refused. The parts must be retained at the dealership for
ninety (90) days after the claim has been filed. If the Service Department would like to inspect the parts, a packing
slip will be mailed to the dealer. The packing slip must be returned with the parts. The parts must be returned pre-
paid within thirty (30) days of receiving authorization. After the parts are inspected and warranty is verified, credit
for the return freight will be issued to the dealer.
3. Parts that will be scrapped at the dealership will be inspected by a Wil-Rich Sales Representative, District Sales
Manager or Service Representative within the ninety (90) day retaining period.

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
3
MODIFICATIONS
It is the policy of Wil-Rich to improve its products when-
ever possible and practical to do so. We reserve the right to
make changes, improvements and modifications at any time
without incurring obligation to make such changes, im-
provements on any equipment sold previously.
TRADEMARKS
Other product and company names mentioned herein may
be trademarks of their respective owners. The use of these
names are for reference only, Wil-Rich uses the names only
to aid in distinguishing different setups of the Planter Bar.
To The Owner ................................................ 3
Assembly Information
24 Row - 22" Spacing .................................... 4
24 Row - 45cm Spacing ................................ 5
Center Frame.............................................. 6-9
Lift Hydraulics ......................................... 10-11
Wing Fold & Markers Hyd ........................... 12
Marker .......................................................... 13
Lift Assembly........................................... 14-15
Forward Wheel Drive Assembly (FWD) ...... 16
Safety lights ................................................. 17
2-1/2" Hub & Spindle w/Tire ........................ 18
Operation
General Information .................................... 19
Safety ...................................................... 20-27
Tire Pressure ................................................ 28
Planter Preparation ...................................... 28
Tractor Preparation ...................................... 28
Leveling........................................................ 29
Wing Fold Circuitry ..................................... 30
Lift Control Circuitry ............................... 31-34
Wing Fold Procedure ............................. 35-36
Wing Unfold Procedure ......................... 37-38
Marker ..................................................... 39-40
Wil-Rich Transmission
Forward Wheel Ground Drive (FWD) .... 42-43
Lubrication .............................................. 44-45
Part's
It is the responsibility of the user to read the Operator's
Manual and comply with the safe and correct operating
procedures as pertains to the operation, lubrication and
maintenance of the product according to the information
outlined in the Operator's Manual.
If this machine is used by an employee or is loaned or
rented, make certain that the operator(s), prior to operat-
ing, is instructed in safe and proper use and reviews and
understands the Operator's Manual.
The user is responsible for inspecting his/her machine and
for having parts repaired or replaced when continued use
of this product would cause damage or excessive wear to
the other parts. The word NOTE is used to convey infor-
mation that is out of context with the manual text; special
information such as specifications, techniques, reference
information of supplementary nature.
When in need of parts, always specify the model and se-
rial number. Write this number in the space provided. The
serial number plate is on the left main toolbar located on
the left side of the lower 7x7.
TO THE OWNER CONTENTS
24R22 Overview........................................46-47
24R45CM Overview..................................48-49
Axle leg (22in)................................................52
Axle leg (45cm)..............................................53
Forward Wheel Drive (FWD)........................54
Marker.......................................................55-56
Fold Hydraulics.............................................58
Lift Hydraulics...........................................59-61
Transmission & Drive Chain ...................62-63
2-1/2in Hub, Spindle & Tires........................64
2in Hub & Spindle.........................................65
Hazard Lights................................................66
Mud Scrapers................................................67
Decals............................................................68
Stinger............................................................69

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 4
(RIGHT SIDE SHOWN - LEFT SIDE
SAME, OPPOSITE HAND)
24 ROW 22 INCH SPACING
ROW UNIT PLACEMENT INFORMATION
NOTE: 2 BAR FOLD LINKAGE MUST
BE UNPINNED TO INSTALL 3/4 GANG
U-BOLT AT THIS LOCATION.
22
22
260
129
195
22
22
22
22
22
22
22
22
22
22
132
44
44
11
24R22 MARKER DOWNGANG

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
5
541CM
270CM
22
CM
45
CM
315 CM
45
CM
45
CM
45
CM
90CM 90CM90CM
45
CM
45
CM
45
CM
45
CM
45
CM
45
CM
24 ROW 45CM SPACING
(RIGHT SIDE SHOWN - LEFT SIDE
SAME, OPPOSITE HAND)

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 6
(LEFT SIDE SHOWN - RIGHT SIDE
SAME, OPPOSITE HAND)
16 ROW 70 CM SPACING
ROW UNIT PLACEMENT INFORMATION
22 70CM
70CM
70CM
70CM
70CM
70CM 35CM
70CM 140CM
210CM
70CM

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
7
BLANK PAGE INTENTIONAL

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 8
7.5x20SL TIRE ASSEMBLY(SHOWN)
2-1/2" HUB & SPINDLE ASSY (12-7/8)
MECHANICAL GROUND
DRIVE ASSEMBLY
SEE PAGES 22-24
RIGHT HITCH WELDMENT
LEFT HITCH WELDMENT
3-1/2x8 LIFT CYLINDER
WING REST
FRONT TOOLBAR PIN ASSY
HITCH ASSEMBLY
SINGLE FOLD LINKAGE
TIRE SCRAPER
DOUBLE FOLD LINKAGE
LEFT SIDE
ASSEMBLYINFORMATION
LEFT MAIN
TOOLBAR
Note: Wil-Rich chain and sprockets are built under
ANSI specifications. Other manufactures design
chain and sprockets under Metric specifications.
This can be a problem if ANSI and Metric are inter-
mixed. Excessive wear and part failure can occur.
CENTER HINGE
SEE DETAIL PAGE 8
WING HINGE
SEE DETAIL
PAGE 9
SEE DETAIL
PAGE 9
FRONTHITCH
SEE DETAIL PAGE 8
LEFT WING 3-1/2x8 LIFT
CYLINDER
(BYPASS)
3-1/4x8 LIFT
CYLINDER
(BYPASS)

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
9
3-1/2x8 LIFT CYLINDER
3-1/2x8 LIFT
CYLINDER (BYPASS)
MARKER REST
RIGHT WING
RIGHT SIDE
SEAL (NOT SHOWN)
RIGHT MAIN TOOLBAR
3-1/4x8 LIFT CYLINDER (BYPASS)
WARNING
THINK!
Safety
First.
Avoid unsafe operation or maintenance.
Make sure tractor engine is turned off
before performing maintenance.
Do not operate or work on this machine
without reading and understanding the
operator's manual.
If manual is lost, contact your nearest
dealer for a new manual.
To avoid Injury, Death or Machine
Damage:
MARKER
ASSEMBLY
SEE PAGES 13
24R22 STRIPPED
5/8NCx2-7/8
STOP BOLT(2)
223952
5/8NCx9 GR5
88557
5/8NCx2-1/4
STOP BOLT
68406
45CM
SPACING
22INCH
SPACING
1/4x1-1/2X
3-1/2 SHIM
30140
SPECIAL HARDWARE
REQUIRED FOR CENTER
ROW UNIT MOUNTING
ASSY HDWR
74277-4

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 10
SAFETY CHAIN
5/8NCx4x5-1/4 U-BOLT
1NCx3-1/2 GR5 BOLT
CENTER
CYLINDER LINK
CYLINDER PIN 1x3-1/8
HITCH ASSEMBLY
FRONT TB PIN ASSY
1-1/4NC LOCK NUT
CAST DUAL HITCH
5/8NCx4x5-1/4 U-BOLT
88145
SIDE WIND JACK
5/8NFx4 GR8 BOLT
1-1/4NCx6-1/2 GR5 BOLT
TB PIN ASSEMBLY
5/8NF LOCK NUT
4x8 TIE ROD CYLINDER
HITCH & CENTER HINGE
WING REST
3/8x3 ROLL PIN
222050
PLASTIC SNAP LOCK
3/8NCx1-1/2 GR5 BOLT
HANDLE HOLDER
222328
1/4x1-3/4 ROLL PIN
88628
HOSE CLAMP
(2-1/4 x 12-1/2)
(2-1/4 DIA x 20)
79247DETAIL
24R22CENTER
CYLINDER PIN 1x4
ASSY HDWR
74277-1

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
11
WING HINGE & MUD SCRAPER
MUD SCRAPER WELDMENT
1-1/4NC HVY NUT
88684
3/4 X 3 FLATWASHER
241044
1-1/4NC X 7 EYEBOLT
241043
CYLINDER PIN 1x4
CYLINDER LOCK PIN
(1/4x2-1/4)
BOTTOM PIN 1x5-5/8
2 BAR FOLD LINKAGE
3/8x3 ROLL PIN
SINGLE FOLD LINKAGE
WING PIN ASSEMBLY(2-1/4x18-3/32)
1-1/4 x 5-5/8 PIN
CYLINDER PIN 1x3-1/8
4x16 TIE ROD CYLINDER
1/2NCx1-1/2 GR5 BOLT
88475
1/2NCx1-1/2 GR5 BOLT
88475
SCRAPER
1/2 FLATWASHER
88347
SPRING LOCK PIN
79247DETAILS
79246SCRAPER
YOKE HUB ASSEMBLYINSTRUCTIONS
TIGHTEN SLOTTED HEX NUT UNTIL
THERE'S A SLIGHT DRAG WHEN THE TIRE
IS ROTATED BY HAND. THEN, BACK OFF
TO THE CLOSEST CROSS HOLE AND IN-
SERT COTTER PIN.
CHECK AFTER FIRST DAYUSE AND
SEASONLYAFTER THAT
ASSY HDWR
74277-5
ASSY HDWR
74277-1B
2INCH HEX WRENCH 241047

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 12
24R22 LIFT HYDRAULICS
1/2x234 HOSE FF
8MJ TEE
8MJ x 8MORB
ELBOW
3-1/2 x 8 HYD CYLINDER
3-1/4x8 SEQ CYLINDER
3-1/2x8 SEQ
CYLINDER
8MJx8MJx8MORB TEE
8MJ x 8MPT ADAPTER
3/8x18 HOSE FF
4MPT x 8FPT
STREET ELBOW
8MPT PILOT
CHECK VALVE
8MORB
x 8FPT
ADAPTER
4 x 8 HYD CYLINDER
3/8x36 HOSE FF
3/8x30 HOSE FF
3-1/2x8 SEQ CYLINDER
3-1/4x8 SEQ CYLINDER
3/8x30 HOSE FF
3/8x78 HOSE FF
8MJ CROSS
MAIN UP
DECAL
3/8x30
HOSE FF
3/8x220 HOSE FF
QUICK DISCONNECT
COUPLER
8MJ x 8MPT
ADAPTER
MAIN DOWN
DECAL
3/8x180 HOSE FF
3/8 TWIN
HALF CLAMP(S)
3/8x132
HOSE FF
3-1/2 x 8 HYD
CYLINDER
8MORB x 8MJ
ADAPTER
FRONT
VALVE MOUNTING
BALL VALVE
PLANTER BAR BRACKET
(WELDED ON)
5/16NCx2x2-3/4 U-BOLT
8MORB x 8MJ
ADAPTER
COVER PLATE
NUT PLATE
5/16NCx1-1/2 HEX BOLT-SINGLE CLAMP
5/16NCX2-1/2 HEX BOLT-DOUBLE CLAMP
1/2 HALF
CLAMP(S)
NUT PLATE
COVER PLATE
3/8x180
HOSE FF
79292ML
ASSY HDWR
74277-12
1/4NCx1-3/4 HEX BOLT-SINGLE CLAMP
1/4NCX3-1/4 HEX BOLT-DOUBLE CLAMP

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
13
8MJ x 8MORB ELBOW
(TYPICAL) 8MJ x8MPT ADAPTER
3/8x18 HOSE FF
1/2NPT PILOT
CHECK VALVE
4x8 TRUNNION CYLINDER
(TYPICAL)
3/8 TWIN
HALF CLAMP
NUT PLATE
COVER PLATE
MAIN DOWN
DECAL
COVER PLATE
1/2 HALF
CLAMP(S)
NUT PLATE
MAIN UP
DECAL
4x8 TIE ROD CYLINDER
3/8x36 HOSE FF
3/8x30 HOSE FF
3/8x62 HOSE FF
1/2x234 HOSE FF
QUICK DISCONNECT
COUPLER
3/8x89 HOSE FF
3/8x156 HOSE FF
3/8x96 HOSE FF
24R45CM LIFT HYDRAULICS
3/8x156 HOSE FF
3/8x89 HOSE FF
3/8x30 HOSE FF
VALVE MOUNTING
79292
ASSY HDWR
74277-13
5/16NCx1-1/2 HEX BOLT
-SINGLE CLAMP
5/16NCX2-1/2 HEX BOLT
-DOUBLE CLAMP
FRONT
8MORB x 8MJ
ADAPTER
8MORB x 8MJ
ADAPTER
BALL VALVE
PLANTER BAR BRACKET
(WELDED ON)
5/16NCx2x2-3/4 U-BOLT
1/4NCx1-3/4 HEX BOLT-SINGLE CLAMP
1/4NCX3-1/4 HEX BOLT-DOUBLE CLAMP
8MJ CROSS
8MJ TEE
8MJ x 8MPT
ADAPTER
4MPT x 8FPT
STREET ELBOW
8MORB x 8 FPT
ADAPTER

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 14
16R70CM LIFT HYDRAULICS
1/2x234 HOSE FF
8MJ TEE
8MJ x 8MORB
ELBOW
3-1/2x8 HYD CYLINDER
3-1/4x8 SEQ CYLINDER
3-1/2 x 8 SEQ
CYLINDER
8MJ x 8MJ x 8MORB TEE
8MJ x 8MPT ADAPTER
3/8x18 HOSE FF
4MPT x 8FPT
STREET ELBOW
1/2NPT PILOT
CHECK VALVE
8MORB x 8 FPT
ADAPTER
4x8 TIE ROD CYLINDER
3/8x36 HOSE FF
3/8x30 HOSE FF
3-1/2x8 SEQ CYLINDER
3-1/4x8 SEQ CYLINDER
3/8x30 HOSE FF
3/8x89 HOSE FF
8MJ CROSS
MAIN UP
DECAL
3/8x30
HOSE FF
QUICK DISCONNECT
COUPLER
8MJ x 8 MPT
ADAPTER
MAIN DOWN
DECAL
3/8x132 HOSE FF
3/8 TWIN
HALF CLAMP(S)
3/8x132
HOSE FF
3-1/2x8 HYD
CYLINDER
VALVE MOUNTING
BALL VALVE
PLANTER BAR BRACKET
(WELDED ON)
5/16NCx2x2-3/4 U-BOLT
8MORB x 8MJ
ADAPTER
COVER PLATE
NUT PLATE
5/16NCx1-1/2 HEX BOLT-SINGLE CLAMP
5/16NCX2-1/2 HEX BOLT-DOUBLE CLAMP
1/2 HALF
CLAMP(S)
NUT PLATE
COVER PLATE
3/8x194
HOSE FF
ASSY HDWR
74277-15
1/4NCx1-3/4 HEX BOLT-SINGLE CLAMP
1/4NCX3-1/4 HEX BOLT-DOUBLE CLAMP
3/8x180 HOSE FF
FRONT
8MORB x 8MJ
ADAPTER

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
15
8MORB x 6MJ ELBOW 8MORB x 8FJX
RESTRICTOR
2-1/2x20 CYLINDER
8MORB x 6MJ
ELBOW
SEQUENCE
VALVE
1/4x30 HOSE FF
DOUBLE
SELECTOR
VALVE
8MORB x
6MJ X 6MJ
TEE
1/4x234 HOSE FF(24R22)
1/4x256 HOSE FF (24R45CM)
WING
DOWN DECAL
8MPT X 6MJ
ADAPTER
QUICK
DISCONNECT
COUPLER
4x16 CYLINDER (1-1/4"DIA PINS)
WING FOLD AND MARKER HYDRAULICS
1/4x84 HOSE FF (24R45CM)
1/4x144 HOSE FF (24R22)
4x16 CYLINDER (1-1/4"DIA PINS)
1/4x328 HOSE FF (24R22)
1/4x288 HOSE FF( 24R45CM)
2-1/2x20 CYLINDER
3/8 MPT X 3/8 FPTX
RESTRICTOR
8MORB x 6MJ
ELBOW
WING UP DECAL
VALVE MOUNTING
SEQUENCE
VALVE
PLANTER BAR BRACKET
(WELDED ON)
5/16NCx2-1/2 GR5 BOLT
ELB 6MJ X 6MPT
ELB 8MJ X 6MJ
5/16NCx1-1/2 GR5 BOLT
DOUBLE SELECTOR
VALVE
3/4 X 3 SPACER
1/4x108 HOSE FF (24R45CM)
1/4x144 HOSE FF (24R22)
1/4x96 HOSE FF (24R45CM)
1/4x144 HOSE FF (24R22)
1/4x116 HOSE FF (24R45CM)
1/4x144 HOSE FF (24R22)
79292WF
79292VALVES
ASSY HDWR
74277-11
FRONT

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 16
CYLINDER LINK
TUBE ASSY 5/8NCx1-1/2
GR5 BOLT
MARKER REST ASSY
1/4DIAx2-1/2 ROLL PIN
5/8NCx9 GR5
1-1/4DIAx9.13 PIN
1-1/4DIAx7.88 PIN
2-1/2 x20 CYLINDER
1-1/4DIAx11.38 PIN
1-1/4DIAx7.88 PIN
1/4DIAx2-1/2 ROLL PIN
1st LINK ARM ASSY
5/8NCx2-1/2 GR5 BOLT
5/8NCx8-1/2 GR5 BOLT
1-1/4DIAx9.91 PIN
SPRING PIN
4-1/2 COMPRESSION
SPRING
CLAMP
3/8NCx1-1/2
GR5 BOLT
DISK BLADE ASSY
38IN DISK ARM
5/8NCx2-1/2 GR5 BOLT
UPPER LINK
ARM ASSY
1-1/4x2-1/4x10GA
MACHINERY BUSHING
1-1/4DIAx4.50 PIN
MARKER
IDLER STRAP WELDMENT
MARKER STRAP WELDMENT
1/4DIAx2-1/2
ROLL PIN
2nd LINK ASSEMBLY
7000303
1/2x7 2HOLE PLATE
5/8NC NUT
ASSY HDWR
74277-6

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
17
24R22in LIFT AXLE ASSEMBLY
5/8NCx2-1/2 GR5 BOLT
4 HOLE
BEARING
67863 HEADLESS PIN(2) 1x5-5/8
424811/4x2-1/4 SPIROL PIN
1" FLAT WASHER
88196
ADJUSTMENT ROD
3/8NCx4 EYE BOLT45636
1/8x1 ROLL PIN
ARM WELDMENT
PLASTIC SNAP LOCK 222050
1/4x1-3/4 ROLL PIN 88628
1-1/2x12-7/8 SPINDLE
SPINDLE LOCK
1NF SLOTTED NUT
3/16x2 COTTER PIN
YOKE HUB ASSY
(SEE PAGE 18)
7.50x29 SL 12 PLY TIRE ASSEMBLY
AXLE PIVOT SHAFT
5/8NCx1-1/2 SQ HEAD SET
SCREW
5/8NC JAM NUT
3/8NC NUT
79244X
ASSY HDWR
74277-3

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 18
24R45cm - LIFT AXLE ASSEMBLY
AXLE LEG SPINDLE
5/8NC
JAM NUT
RIGHT LOCK-
ING CYLIN-
DER MOUNT
1/2X5 PIN
STOP PLATE
SIDE ARM
1NC X 3-1/2 GR5
LEFT CYLINDER MOUNT
RIGHT CYLINDER
MOUNT
ROD CAP
5/16NCX5/16 SET SCREW
3 HOLE SHIM(USED AS
NECESSARY FOR
ALIGNMENT)
4X8 TRUNNION CYLINDER
3/4NCX6-1/2
GR5
LEFT LOCK-
ING CYLIN-
DER MOUNT
4HOLE
BEARING
BLOCK
5/8NCX2-1/2
GR5
TWIN AXLE
OSCILLATING
BEAM
7.5x20SL MONO-RIB
TIREASSEMBLY
SEE PAGE 18
1/2NF
LOCK NUT
2IN HUB & SPINDLE
SEE PAGE 18
5/8NCX1-1/2
SQ HD SET SCREW
1/2NFX3-1/4 GR5
1/2NX1-1/4 GR5
1/2 LOCK WASHER
1/4X2-1/4 FLAT WASHER
1-3/4X6 SHAFT
24R45cm
TRANSPORT LOCK (4)
TYPICAL
LAYOUT2A
ASSY HDWR
74277-2
1 X 3-1/8 PIN 42473
1/4 X 2-1/4 ROLL PIN 42484

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10
19
FORWARD WHEEL DRIVE (FWD)
NO50x13 tooth IDLER
1/2NCx2 GR5
RH 7.60-15 PWR
IMPLEMENT - SHOWN
LH 7.60-15 PWR
IMPLEMENT - OPPOSITE
5/8NCX2-1/2 GR5
FWD TRANSMISSION
5060 IDLER HUB
1.75 INTERNAL SNAP RING
1/2NCX3 GR5
5/8NCX2-1/2 GR5
1IN SPRING
TENSION BUSHING
SPRING ARM
1/2NF WHEEL NUT
28TOOTH DRIVE
SPROCKET
1/2NC LOCK NUT
1/2NCX3-1/4 GR5
1/2NFX2-1/2
TAP BOLTGR5 5/8 FLAT WASHER
1ODX3 BUSHING
5/8 FLAT WASHER
1ODX2 BUSHING
NO60x15 TOOTH
IDLER
5/8NCX7 GR5
5/8 LOCK WASHER
RIGHT LEG - SHOWN
LEFT LEG - OPPOSITE
1/2NFX1
WHEEL BOLT
NO50x13 tooth IDLER
1/2NCx2 GR5
5/8 BORE BEARING
1 NC NUT (DOUBLE)
1 FLAT WASHER
1/2X2-3/8X8
COMPRESSION SPRING
1-5/16X6 SLEEVE
1-1/2 DIA BEARING BLOCK
1NC X17-1/4
SPRING ROD
1 FLAT WASHER
1 NC NUT
(DOUBLE)
1/2 LOCK NUT
1/2NCX3-3/4 GR5
1/2NC LOCK NUT
LAYOUT4A
ASSY HDWR
74277-7
2IN HUB &
SPINDLE(2 HOLE)-
USE OUTSIDE HOLE

WIL-RICH ASSEMBLY/OPERATOR'S MANUAL 74277 12/10 20
SAFETY LIGHT ASSEMBLY
223144
RED LIGHT (2)
FWD PLANTER BAR
(SMV) SLOW MOVING VEHICLE &
LIGHT PLACEMENT
64597 35FT HARNESSS
223145 AG MODULE
223146 WISHBONE 4 LEAD
NOTE: ROUTE WISHBONE
THRU LIGHT ARMS
LEFT
RIGHT
223143 AMBER
LIGHT(2)
223126 LIGHT BRACKET (4)
88203 1/4NC X 1 BOLT(16)
1/4NC NUT(16)
NOTE: MOUNT AMBER
LIGHTS AS WIDE AS POS-
SIBLE. THE AMBER LIGHTS
MUST BE MOUNTED NO
MORE THAN 16” FROM THE
IMPLEMENT EXTREMITIES.
REAR
241036 5/8X7 LIGHT BASE (4)
88402 3/4X9 HEX BOLT(4)
223144 - 12X36 LIGHT ARM (4)
88702 - 3/8NC X 3/4 SQHD SET SCREW (8)
88103 - 3/8NC NUT (8)
NOTE: MOUNT THE LIGHT BASE
BACK TO BACK WITH THE ROW UNIT,
BEFOREATTACHINGANY HYDRAULIC
HOSES OR ELECTRICAL WIRES.
SMV EMBLEM 30651
SMV KIT 239176
SMV POLE MOUNT 239174