WOOSIM WSP-i350 User manual

http://www.woosim.com
MODEL WSP-i350
(3inch Rugged Mobile Printer)
Rev. 4.3
All specifications are subjected to change without notice

WSP-i350 Rev. 4.3
http://www.woosim.com
2
 Copyright
WSP-i350 3inch Rugged Mobile printer operator’s manual.
Copyright ⓒ2017 by Woosim Systems Inc.
All rights reserved.
The information contained in this manual is the property of Woosim Systems Inc.
And may not be reproduced in whole or in part without the prior written permission of Woosim
Systems Inc.
 Trademark
a registered trademark of Woosim Systems Inc.
All other trademark are the properties of their respective companies.
 Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the printer
“OFF”, before you connect or removed the cable on the rear side, in order to guard the printer
against the static electricity.
If the printer is damaged by the static electricity, you should turn the printer “OFF”
 Notice
The contents of this manual are subject to change without notice.

WSP-i350 Rev. 4.3
http://www.woosim.com
3
 Introduction
The WSP-i350 is the ideal solution for Mobile banking system , Retail,
point of sales, Credit card Transaction, other traveling and mobile computing etc.
The general features of WSP-i350 printer are as follows:
Compact size (120×130.5×58.4mm)
Light weight(395g) for true mobility [standard]
Very silent printing thru direct thermal printing method
High speed (130mm/sec, MAX)
High resolution(203dpi : 8dots/mm).
UART(RS-232C or TTL), Bluetooth Ver3.0,
USB[option], Wireless LAN(IEEE802.11b/g/n) [option] interface
Support Magnetic Stripe Reader[option]
Support Graphic LCD(128×32dots) with Blue LED Backlight
Support text and graphic printing
Intutive LED’s indicate Power(on/off), Error
Easier paper roll loading by CLAMSHELL design
One touch paper cover
Printer door open & Paper-out sensor
Easier maintenance with self-diagnostic.
In field programming –Update Firmware, Download Fonts and Logos
Water-resistant construction.( IP54 –Certified without case)
Microsoft Windows/Windows CE, Linux, Android, iOS compatible
Flow control : Software (XON/XOFF)
※Hardware flow control not supported in printer.
Free fall: 1.8 meter
Agency Approvals

WSP-i350 Rev. 4.3
http://www.woosim.com
4
 Operating Precautions
Please follow the precautions below to enjoy and maintain the full performance of the printer.
Using the Printer
● Be careful not to drop or bump the printer on a hard surface.
● Do not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as follows:
◆ Operating temperature :-15°C to 50°C
◆ Relative humidity : 10% to 90%
● Do not install the printer near devices that generate strong
electromagnetic fields such as a copy machine.
● Do not open the platen cover during printing .
● Do not remove or reinstall the communication cable during printing
or transmission.
● Do not touch the connectors of the communication during printing.
● Switch the POWER OFF when not in use.
● Do not use other solvent.
●The AC adapter, the battery charger and the battery pack may
become warm when in use. This is normal and is not a malfunction.
● When the battery pack is used at low temperature, the length of time
the printer can be used may be shortened.
Thermal Paper Handling
● Store the thermal paper in a cool, dry and dark place.
● Do not rub the paper with hard object.
● Do not leave the paper with hard object.
● Do not allow plastic film, erasers, or adhesive tape to touch the paper
for long periods.
● Do not stack the thermal paper with diazo copies immediately
after copying or wet-type copies.
● Do not use chemical glue.
●Always use the clean thermal paper.

WSP-i350 Rev. 4.3
http://www.woosim.com
5
Federal Communications Commission
Radio Frequency Interference Statement
FCC ID : QDDWSP-I350X
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
ㆍReorient or relocate the receiving antenna.
ㆍIncrease the separation between the equipment and receiver.
ㆍConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ㆍConsult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment
under FCC rules.
This Device has been evaluated to comply with RF exposure requirement for general use
limit in portable condition. It is safe to be used in sold condition.
CE WARNING
ㆍChanges and modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
ㆍIt is desirable that it be installed and operated with at least 20cm or more between the radiator and
person’s body(excluding extremities hand, wrists, feet, and ankles)

WSP-i350 Rev. 4.3
http://www.woosim.com
6
CONTENTS
1. Outline. ................................................................................................................................................................ 7
1.1. Model classifications................................................................................................................................. 7
1.2 Symbol......................................................................................................................................................... 7
1.3 Product Part Number System................................................................................................................... 8
1.4. Specifications. ............................................................................................................................................ 9
2. Setting up the printer......................................................................................................................................11
2.1. Printer & Accessories...............................................................................................................................11
2.2. Printer Features ........................................................................................................................................12
2.3. Dimensions................................................................................................................................................13
2.4. Replacing paper roll.................................................................................................................................15
2.5. Power supply ............................................................................................................................................16
2.5.1. Specified power supply.................................................................................................................16
2.5.2. Installing the battery .....................................................................................................................16
2.5.3. Recharging the battery pack ........................................................................................................17
2.6. Set operation mode.................................................................................................................................18
2.7. Confirmation of the Wireless-LAN information....................................................................................22
2.7.1. MAC Address printing...................................................................................................................22
2.7.2. Confirmation of the Wireless-LAN setting information ............................................................22
3. Interface..............................................................................................................................................................23
3.1. UART or USB.............................................................................................................................................23
3.2. Bluetooth...................................................................................................................................................24
3.3. Wireless LAN.............................................................................................................................................24
3.4. Magnetic stripe card reading..................................................................................................................24
4. Using the printer...............................................................................................................................................25
4.1. Control panel. ...........................................................................................................................................25
4.2. The self test ..............................................................................................................................................26
4.3. Using the Accessory ................................................................................................................................26
4.3.1. Using the Shoulder strap..............................................................................................................26
4.3.2. Using the Belt clip .........................................................................................................................27
5. Consumable Parts.............................................................................................................................................28
5.1. Recommended paper...............................................................................................................................28
5.2. Printing position. ......................................................................................................................................28
6. Revision History ................................................................................................................................................29

WSP-i350 Rev. 4.3
http://www.woosim.com
7
1
1. . O Ou ut tl li in ne e. .
1
1. .1 1. . M Mo od de el l c cl la as ss si if fi ic ca at ti io on ns s. .
1
1. .2 2 S Sy ym mb bo ol l
Standby symbol
IEC 5009, the standby symbol(line partially within a broken circle),
Indicates a sleep mode or low power state.
Direct current symbol
This symbol is found on many electronic devices that either require or
produce direct current.
WSP-i350 ( ) ( )
Model
Interface
A1 : UART/Bluetooth
(Standard)
Power
None : DC 8.4V

WSP-i350 Rev. 4.3
http://www.woosim.com
8
1
1. .3 3 P Pr ro od du uc ct t P Pa ar rt t N Nu um mb be er r S Sy ys st te em m
Model name / Interface Spec.
Example) 1. Porti-S40 Serial/Bluetooth Part No. ⇒S40/A1
2. Porti-SC30 Bluetooth Only Part No. ⇒SC30/Z1
Note) The above table is the interface format which is supported.
But some of the interfaces are not supported according to the product
and please contact us, if you have any questions regarding the interface.
S40
SC30
W25
.
.
.
Wired
Wireless
A
RS-232C
1
Bluetooth
B
TTL
2
IrDA
C
USB
3
Wireless LAN
D
RS-485
0
None
E
Parallel
Z
None

WSP-i350 Rev. 4.3
http://www.woosim.com
9
1
1. .4 4. . S Sp pe ec ci if fi ic ca at ti io on ns s. .
Item
Specifications
Print method
Direct thermal line printing
Character size
- Font Size A: 12X24 / Font Size B : 9X24 / Font Size C : 8X16
- KOR : 24X24(16X24) / CHN, JPN : 24X24
Characters per line
- Font A : 48cpl / Font B : 64cpl / Font C : 72cpl
- KOR, CHN, JPN : 24cpl
Optional Characters
Alphanumeric:95, Extended Graphics:128X50 pages, International:10,
Simplified/Traditional Chinese, Japanese, Korean(optional)
Resolution
203dpi, 8dots/mm
Print width
3-inch (72mm, 576dots)
Print speed
130mm / sec (MAX)
Dimension
120×130.5×58.4mm
120×132.5×58.4mm (MSR model)
Weight (w/o roll paper)
395g / 407g (MSR model)
Interface
UART(RS-232C or TTL), Bluetooth Ver4.0 + EDR
USB(option), Wireless LAN(IEEE802.11b/g/n) [option]
Paper roll
Thermal roll paper (80mm wide, 50ø)
Barcodes
1-dimension : UPC-A, UPC-E, EAN-8, EAN-13, CODE-39, CODE-93,
CODE-128, ITF, CODABAR
2-dimension : PDF417, Micro PDF417, Truncated PDF417, QR-CODE,
DATA Matrix, Maxicode
Etc :GS1 databar
Driver
Microsoft Windows, Linux
H/W Spec
MCU : RX-32bit, RAM : 128M bit, FLASH : 64M bit
Receive buffer size
1M bytes
Sensor
Support Cover open, Paper, Label
MSR [option]
1&2 or 2&3 Track Reading
LCD
128×32 Dots FSTN (Blue LED Backlight)
Battery
Rechargeable 7.4V DC, 2200mAh (Standard), 2600mAh (Option)
Operation time : Up to 12h with around 1000 bills and 200mm/bill
Battery duration
1 hour continuous printing
Battery charger
Input (100~250V AC, 50~60Hz)
Output(8.4VDC/0.8A), 4hours full charge time
( Continue…)

WSP-i350 Rev. 4.3
http://www.woosim.com
10
Item
Specifications
Environment
conditions
Temperature
-15°C ~ 50°C (operating)
-15°C ~ 70°C (storage)
Humidity
10% - 90% (operating)
MCBF(Mean Cycle
Between Failure)
Mechanical
37,000,000 lines
Head
≥100Km
< Table 1 >

WSP-i350 Rev. 4.3
http://www.woosim.com
11
2
2. . S Se et tt ti in ng g u up p t th he e p pr ri in nt te er r
2
2. .1 1. . P Pr ri in nt te er r & & A Ac cc ce es ss so or ri ie es s
Your printer box should include these items. If any items are damaged or missing, please
contact your dealer for assistance.
WSP-i350
Battery Pack
▼ OPTIONAL
Communication cable
Shoulder strap
MSR
Thermal roll paper
Battery charger adaptor
Belt clip
Car charger

WSP-i350 Rev. 4.3
http://www.woosim.com
12
2
2. .2 2. . P Pr ri in nt te er r F Fe ea at tu ur re es s
MSR model
Standard model

WSP-i350 Rev. 4.3
http://www.woosim.com
13
2
2. .3 3. . D Di im me en ns si io on ns s
▶Standard model
120
130.5
58.4

WSP-i350 Rev. 4.3
http://www.woosim.com
14
▶MSR model
120
132.5
58.4

WSP-i350 Rev. 4.3
http://www.woosim.com
15
2
2. .4 4. . R Re ep pl la ac ci in ng g p pa ap pe er r r ro ol ll l. .
1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the
picture.
3. Insert a new paper roll as shown.
4. Tear the excess paper off using the edge of paper door as a tear bar.
Note : Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the printer can not
detect the paper end correctly.

WSP-i350 Rev. 4.3
http://www.woosim.com
16
2
2. .5 5. . P Po ow we er r s su up pp pl ly y
2
2. .5 5. .1 1. . S Sp pe ec ci if fi ie ed d p po ow we er r s su up pp pl ly y
2
2. .5 5. .2 2. . I In ns st ta al ll li in ng g t th he e b ba at tt te er ry y
① To install battery pack, proceed as follows:
Insert the battery in the arrow direction and make sure the lock completed
② Reverse the order to remove the battery pack.
The following specification is requested for Power supply.
Battery Charger : DC 8.4V/0.8A
Avoid using power supply which its power capacity of power current is extremely high.
Warning :
●Before installing or removing the battery pack, ensure the printer is OFF.
● If the printer is not used for long period of time, remove the battery pack from the printer.
● Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
● Batteries are provided not being charged. Please charge the battery before use.

WSP-i350 Rev. 4.3
http://www.woosim.com
17
2
2. .5 5. .3 3. . R Re ec ch ha ar rg gi in ng g t th he e b ba at tt te er ry y p pa ac ck k
For recharging the battery pack, install the battery pack in the printer.
Insert the Battery Charger to the charge connector of the printer.
NOTE : ● While charging the printer, turn off the printer power.
● Do not remove the battery during charging.
●The battery is consumable parts and when purchasing, compared to the use hour
is gradually decreases. (Warranty 6 month)
● If the printer is not used for a long time, unplug the power cord from the printer
and outlet.
● The recharging time depends on the voltage level and ambient temperature of
the battery. Normally, if takes about 4 hours to recharge a battery pack.
● You must use only the supplied adapter.
●Red Lamp : charging the battery.
Green Lamp : charging is finished.

WSP-i350 Rev. 4.3
http://www.woosim.com
18
2
2. .6 6. . S Se et t o op pe er ra at ti io on n m mo od de e
In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5
times, the printer comes out at the circumstance to change the printer mode. (refer Table 2)
** Only the printer which support iOS Bluetooth interface comes out at the circumstance to change
the printer mode. (Bluetooth Mode or Boluetooth(iAP) Mode).
** Manipulation methods :
1. Press Feed and Power buttons simultaneously until the ERROR lamp blinks 5 times and
then keep pressing two buttons for 2 Seconds.
2. After the printer beeps twice, the Bluetooth mode is changed
and it will print the result of change.
3. The changed mode can be checked in the printout.
Example ) If the printer is in Bluetooth Mode →Bluetooth(iAP) Mode
If the printer is in Bluetooth(iAP) Mode →Bluetooth Mode
** If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth
function of the current paired Smartphone.
** Methods :
1. Turn off the Bluetooth function of the current paired Smartphone.
(Bluetooth ICON in LCD is disappeared.)
2. Change the printer mode.
(Additionally, we want to recommend you to rest(OFF→ON) the printer and change mode.)
Printer LCD status
Android status iOS status

WSP-i350 Rev. 4.3
http://www.woosim.com
19
FEED button : changing Printer MODE status.
POWER button : changing OPTION status.
[Example] The defaults of the printer are :
UART / 9600 bps / 8 data bit / No parity /1 stop bit / Density low /
Quality low / Mark use / Sensor High / 5 min Off
If a user wants to modify the defaults with
Bluetooth / 57,600 bps / 7 data bit / Odd parity /2 stop bit / Density high /
Quality high / Mark no use / Sensor Low / No use
Press FEED & POWER Button during the Error Lamp flickers 5 times.
You will see present COMMUNICATION mode in the LCD. (UART)
Press the POWER Button twice. And then, interface mode has set to
Bluetooth mode.
When you press FEED button once.
You will see present BAUD RATE mode in the LCD. (9600 bps)
Press POWER Button 3 times. And then, BAUD RATE has set to 57,600 bps.
When you press FEED button once.
You will see present DATA BIT mode in the LCD. (8 Data bit)
Press POWER Button once. And then Data Bit has set to 7 DATA BIT.
When you press FEED button once.
You will see present PARITY mode in the LCD. (No parity)
Press POWER Button once. And then the Parity bit has set to ODD Parity Bit..
When you press FEED button once.
You will see present STOP BIT mode in the LCD. (1 stop bit)
Press POWER Button once. And then the density has set to 2 Stop bit.
When you press FEED button once.
You will see present DENSITY mode in the LCD. (Density low)
Press POWER Button twice. And then the density has set to Density high.
When you press FEED button once.
You will see present Quality mode in the LCD. (Low)
Press POWER Button once. And then the quality has set to Quality high.

WSP-i350 Rev. 4.3
http://www.woosim.com
20
When you press FEED button once.
You will see present MARK mode in the LCD. (Use)
Press POWER Button once. And then the mark has set to Mark no use.
When you press FEED button once.
You will see present SENSOR mode in the LCD. (High)
Press POWER Button once. And then the sensor has set to Sensor Low.
When you press FEED button once.
You will see present POWER DOWN mode in the LCD. (5 min Off)
Press POWER Button once. And then the Power down has set to Power down no use.
If all the mode have set, press the POWER Button and the FEED Button at the same time.
After then release the buttons at the same time.
Bluetooth / 57600bps / 7 data bit / Odd parity / 2 stop bit / Density high /
Quality High / Mark No use / Sensor Low / no use