Wren Wall unit User manual

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
288 x 600
360 x 600
288 x 800
360 x 800

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
Hanging Bracket
X2 Inc Screws
(F) x8
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x8
Cover Cap
(N) x1
Door
Buer
(T) x10
Back Panel
Support Clip
Hanging Bracket Plate
X2 (Screws Not Included)
Hinge Mounting
Plate X2 Inc Screws
Hinge
X2 Inc Screws
Corner
Gusset
X2
Hanging Bracket
Cover Cap
X2
Lift Hinge
X2 Inc Screws
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 2
Step 1.
Seat dowel (F)
into holes in
end panel (B) as
shown.
Step 2.
Seat cam dowel (G)
into holes in
end panel (B) as
shown.
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
& cam locks (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Slide panel (A) into the groove
of panels (B) and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
A
C
CB
BB
CC
H
H
G
G
View from underside View from underside
Seat (G)
cam dowel
into hole as
shown.

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 3
Step 6.
Seat dowel (F)
into holes in
both panels (B) as
shown.
Step 7.
Seat cam dowel
(G) into holes in
both end panels (B)
as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
& cam lock (H) (in blue)
and also using dowels (F)
(in orange) in positions as
shown. Ensure panel (A) is
seated into the groove of
panel (B).
Step 9.
Cam Lock (H)
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
B
B
A
C
H
H
C
Seat (G)
cam dowel
into hole as
shown.
G
G
F
F
F
F
G
G
B
BB
CC
H
H
G
G
View from underside View from underside
G
G

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 4
Step 11.
Slide the back panel clips (T) into the groove of both
panels (B) & (C). The back panel clips (T) should be
evenly spaced as shown and positioned to allow the
hanging bracket and corner gussets to be tted. Once in
place, tighten screw.
The side back panel Clips should be disregarded for
the 288 units.
Step 10.
Ensure carcass is square.
BA
C
A
T
A
T

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 5
Step 13.
Secure corner gussets to the bottom left and
right hand side of the wall unit using
4 x 15mm screws (L) per plate.
Step a
Insert Hanging
Bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
S
S
Detail A Detail A Detail A
View though
Back Panel
Pilot
hole
M
Detail B
L
L
L
L
Detail B
A
B
Step 14.
Drill a small pilot hole through the centre of the Corner Gussets.
Use this hole at the end of the process to screw through and
into the wall. Cover the screw heads using the cover caps (M)
provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.
Step 12. Hanging Brackets steps a,b & c to be carried
out on both sides as shown

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 6
Step 15.
Measure and attach Hinge Mounting Plate onto xed shelf (C) as shown,
using screws which are already positioned within the Hinge Plates.
Step 16.
Measure and attach lift hinge
bracket with 2 x screw per bracket.
The required screws are included
inside lift hinge pack.
Step 19.
Secure hinges by tightening
2 x screws with plastic grommet
attached. These are already
positioned within the hinges.
Step 18.
Insert hinges into holes provided.
C
TOP FIXED SHELF
Front Front
37 37
Left Right94 94126 126
Hinge Plates
142142
110110
BackBack
Left
Right 3030
FRONTAL
192 192
160 160
Top Top
Front Front
37 37
Removed from lift hinge
B
B
C
Step 17.
Measure and attach lift hinge bracket to frontal with 2 x screw per
bracket. The required screws are included inside lift hinge pack.
LEFT HAND RIGHT HAND
B B

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 7
Step 20.
Measure appropriately and attach the 2 x hanging bracket plates onto the
wall screwing through the provided holes into your wall.
Screws for xing to walls are not provided as these vary depending
on your wall material and construction. Ensure appropriate xings for
wall construction are used.
Step 21.
Hang the cabinet using
the brackets to hook
onto the plate as shown
Hanging Bracket
Plate
Step 22.
Using points a, b & c adjust the Cabinet to suit.
Step a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre
screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed though
Back Panel
b
C c
a
a
b
K
Step 24.
Screw into any side units using the
provided 2x 30mm screws (K) to
secure the unit. Screw just to the
rear of the hinge plate then place a
cover cap on the head to conceal it.
Care to be taken. Hanging procedure
is neccesary for a safe installation.

WALL UNIT
600 - 800 Lift
Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600-800_Lift_Rev4.indd
Page 8
Step 24.
Clip hinges into hinge mounting plates on
the unit.
Step 25.
Clip lift hinge mechanisms
into each bracket.
Step 26.
Use a 4mm allen key to adjust
the strength of the lift hinge for
the door weight.
Hinge Cover Caps
Step 27.
Fit cover caps to hinge.
Adjust Softclose to suit.
The left and right hinges MUST be
adjusted to the SAME STRENGTH.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
1
2
FRONTAL HINGE
ADJUSTMENT
View from Inside of Carcase
To release door,
pull catch as shown,
to release hinge from
the hinge plate. The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.

WALL UNIT
600 - 800 Lift
Assembly Guide

WALL UNIT
600 - 800 Lift
Assembly Guide