Wren TOWER UNIT User manual

2070 x 300 2070 x 600
2250 x 300
Tall
2250 x 600
Tall
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

View from underside
LGE L Bracket
x2
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
(U) x2
Fixing Plate
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x16
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
(SS) x24
Shelf Peg
Plastic
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel C
x2 Base Panel
Panel E
x2 Rail
Shelf
x6
Legs
x5
Frontal (packed separately)
x2
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 1
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

BB
C
C
View from underside
View from underside
H
G
G
H
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
Step 3.
Carcass construction
Attach panels (C) & (E) to panels (B),
using cam dowel (G) & cam lock (H) (in blue),
and also using Dowels (F) (in orange) in positions as shown.
NB. All CAM LOCK (H) are to be positioned facing
the outside of the unit carcass, for ease of tightening.
Step 4.
Join panels (C) & (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
Seat (G)
cam dowel
into hole
as shown
Do not use power tools with
cam dowel (G) or cam lock (H)
B
E
E
C
B
C
G F F G
G F F G
B
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 2
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

Step 5.
Slide back panel (A) into groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square
with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H),
this will expand cam dowels
(G) and tighten the unit
together.
9mm
9mm
C
B
B
E
E
A
K
A
C
K
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 3
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

B
B
Step 8.
Secure each of the legs into place with 2 x 15mm screws (L) per leg
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Step 9.
Lightly hit centre peg of leg base with hammer
until ush with the leg base.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Front
Front
Leg position diagram
C
C
C
B
L
LC
B
B
C
B
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 4
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

2070 TALL 2250
Step 11.
Hinge mounting plate
attach hinge plates onto end
panels (B) In locations shown
using 8 x 15mm screws (L)
Hinge side to be mounted
in accordance to customer
kitchen plan.
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the L brackets
to the cabinets at either side. Then screw through into the
wall as shown.
Screws for xing to walls are not provided as these
vary depending on your wall material and construction.
Ensure appropriate xings for wall constructions are
used.
Secure tower to the wall using screws through rail panel (E) into the
wall as shown.
Screws for xing to walls are not provided as these vary depending on
your wall material and construction. Ensure appropriate xings for wall
constructions are used.
L
L
L
L
L
L
L
L
L
E
E
L
B
B
BB
Securing to Adjacent Units
Screw into any side units using
the 30mm screws (K) provided to secure to unit.
Screw just to the rear, at the top and bottom of
both sides of the unit, place a cover cap on the
head to conceal it.
K
846
846
626
626
126
2006
1826
2006
814
814
594
594
94
1974
1794
1974
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 5
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide

Hinge cover caps
See Customer Specific Kitchen Plan
For Tower Frontals
Fixing plates
Hinges
Step 14.
Align doors to join together using 2 xing plates to the back of
both frontals ensure a 3mm gap is maintained between each
frontal once xed together.
Screw in place using 4 x 15mm screws per xing plate.
View from inside of carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- left - right
Point 2- side - side
To Release door
Pull catch as shown,
to release hinge from
the hinge plate.
FRONTAL HINGE
ADJUSTMENT
Step 12.
Insert hinge where required
in holes as shown.
Step 13
Secure hinges by
tightening
2 screws with hinge
dowels attached. These
are already positioned
within the hinges.
1
2
Step 16.
Fit cover caps to hinge.
Step 15.
Adjust hinge to suit. As shown below.
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev2.indd
Page 6
TOWER UNIT
300 600 2 Door 6 Shelf
Assembly Guide