Wren FRONTALS User manual

FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Bi Fold Lift
Piston Lift

Page 1
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Step 1.
Secure piston brackets with 2 x 15mm screws into position as shown, using pilot holes on the
frontal as a guide. See g 1.
Piston Plate
Step 2.
Discard existing hinge dowels and replace with new ones provided.
Step 3.
Insert hinges into hinge holes provided. See g 1.
Step 4.
Secure hinges with the 2 x original screws.
Piston Lift
Hinge Dowels
g 1
g 2

Page 2
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Piston Lift
Both hinges MUST be adjusted to the SAME STRENGTH.
Step 6.
Adjust hinges to suit, using the highlighted screw(s)
shown.
Step 7.
Fit cover caps to hinges and adjust soft-close to suit.
Step 8.
Clip piston onto piston mounting plates on the unit and frontal.
Step 5.
Attach the door to unit, clip hinges onto hinge plates and
click to secure. See g 2.
BA C
AA
B
C

Page 3
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Step 1.
Line up and insert 3 x mechanism pins into holes provided as shown.
Step 2.
Tighten 3 x screws on each Bi Fold mechanism into the unit. These are already positioned within the mechanism.
Bi Fold Lift
Measure from Top - Front edge of unit
View from inside of unit
top of left hand end panel
End panel mechanism pin hole locations
3 x mechanism pins
View from inside of unit
View from rear of Bi Fold mechanism
3 x mechanism
screws

Page 4
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Step 4.
Insert top hinges into hinge holes provided on one frontal. On the same frontal, x
centre hinge mounting plates as shown in g 1.
Step 3.
Discard existing hinge dowels and replace with new ones provided.
Step 5.
Insert centre hinges into hinge holes provided on the second frontal. Secure all hinges with 2 x original screws
per hinge.
CENTRE HINGE
MOUNTING
PLATES
Step 7.
Secure Bi Fold arm clip to the frontal location as shown,with 2 x 15mm screws per clip as shown in g 2.
Step 6.
Attach frontals together, clip centre hinge into hinge mounting plate & click to secure.
Hinge Dowels
Centre hinge with
mounting plate
Bi Fold Lift
g 1 g 2

Page 5
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Step 8.
Attach frontals to the unit. Clip hinges onto the hinge plates and click to secure.
Step 9.
Clip arms onto BiFold arm clips.
Please refer to lift hinge instructions provided or visit website: hafele.com/external/free for further frontal adjustment information if required
Bi Fold Lift

Page 6
FRONTALS
Lift Mechanism Replacement Frontal Guide
For Internal Use: FI.WR.INS.080_WKIN00070_LiftMECH_ReplaceFRTL_Rev6
Please refer to lift hinge instructions provided or visit website: hafele.com/external/free for further frontal adjustment information if required
View from inside of unit
Both hinges MUST be adjusted to the SAME STRENGTH.
Step 10.
Adjust hinges to suit, using the highlighted screw(s)
shown.
Step 11.
Fit cover caps to hinges and adjust soft-close to suit.
Step 12.
Fit cover to lift mechanisms.
Bi Fold Lift
BA C
AA
B
C