Yealink SIP-T23P User manual

1. Pull the hookswitch tab in the handset cradle.
2. Rotate the hookswitch tab 180 degrees.
3. Reinsert the hookswitch tab.
The hookswitch tab has a lip which allows the handset to
stay on-hook when the IP phone is mounted vertically.
To adjust the hookswitch tab:
Adjust the hookswitch tab as shown below(Take a
SIP-T21P IP phone as an example):
Wall Mount Quick Installation Guide
for SIP-T23_T22_T21_T20_T19 IP Phones
This quick installation guide provides step-by-step
instructions for mounting your IP phone to a wall.
SIP-T19(P) IP Phone
www.yealink.com
Wall mount is avaliable for the following IP phones:
SIP-T22(P) IP Phone
Wall Mount Quick Installation Guide
180。
Adjusting the Hookswitch Tab
The IP phone is packaged with the hookswitch tab in
desk mount position. Before mounting the IP phone to
a wall, you must set the hookswitch tab to wall mount
position.
SIP-T21(P) IP Phone
SIP-T20(P) IP Phone
Depending on which model you own, your IP phone can
be mounted to the wall in one of two ways:
By using the stand(included with SIP-T23P/T23G/T22(P)
/T21(P)/T21(P) E2 /T20(P) IP phone)
By using the slots on the back of the phone
(for SIP-T19(P)/T19(P) E2 IP phone)
Screws, wall anchors and applicable tools are also
required for wallmount installation. These are not
included with your IP phones. You need to purchase
them separately.
SIP-T23P/G IP Phone
SIP-T21(P) E2 IP Phone
SIP-T19(P) E2 IP Phone

Attach the stand to the IP phone as shown below
(Take a SIP-T21P IP phone as an example):
1. Insert the tabs on the stand into the slots on the back
of IP phone. And then slide the stand to up.
Wall Mount Quick Installation Guide
www.yealink.com
To adjust the stand(Not applicable to the
SIP-T19(P)/T19(P) E2 IP phone):
1. Detach the reversible bracket from the stand.
2. Rotate the reversible bracket 180 degrees.
3. Attach the reversible bracket to the base.
Adjusting the Stand Attaching the Stand to the IP Phone
To attach the stand to the IP phone(Not applicable
to the SIP-T19(P)/T19(P) E2 IP phone):
SIP-T23P/G, SIP-T22(P), SIP-T21(P), SIP-T21(P) E2 and
SIP-T20(P) IP phones are mounted to the wall via the
stand which consists of the reversible bracket and the
base, as shown below:
The reversible bracket
SIP-T19(P)/T19(P) E2 IP phones are mounted to the wall via
the slots on the back of the phone. If you are using a
SIP-T19(P)/T19(P) E2 IP phone, see the section ”Mounting
the IP Phone to the Wall“.
The base
Adjust the stand as shown below:
1
2
Mounting the IP Phone to the Wall
Yealink provides the wall mount drilling template for
each IP phone model, which locates and marks the
position for mounting the anchors/screws (not provided)
on the wall, as shown below:

www.yealink.com
For SIP-T23P/T23G/T22(P)/T21(P)/T21(P) E2/T20(P) IP phones:
Copyright 2015 YEALINK NETWORK TECHNOLOGY CO.,LTD.
c
Following the drilling template above, you can mount
the IP phone to the wall, as shown below
(Take SIP-T21P and SIP-T19P IP phones as examples):
You can also download the wall mount drilling template
online: http://www.yealink.com/Support.aspx.
For SIP-T19(P)/T19(P) E2 IP phones:
For a SIP-T21P IP phone:
For a SIP-T19P IP phone:
2
155mm
Screw position
2
Screw position
104mm