ZOLL M Series CCT User manual

CONFIGURATION GUIDE
9650-0204-01 Rev A October 2006

An issue or revision date for this manual is shown on the front cover.
If more than three years have elapsed since this date, contact ZOLL Medical Corporation to determine if additional
product information updates are available.
ZOLL, M Series, and stat.padzare registered trademarks, and PD, and XL are trademarks of ZOLL Medical
Corporation.
12SL and Catalyst MUSE are trademarks of GE Medical Systems.
Copyright 2006 by ZOLL Medical Corporation. All rights reserved.

Table of Contents
1-1
INTRODUCTION............................................................................................................................. 1
CONFIGURING THE UNIT ............................................................................................................1
SELECT LANGUAGE 2
MAIN CONFIGURATION MENU ...................................................................................................3
PRINT CONFIG .............................................................................................................................3
RESTORE DEFAULTS ...................................................................................................................3
READ FROM CARD .....................................................................................................................4
CHANGE CONFIG ........................................................................................................................5
CONFIGURATION SETTINGS ......................................................................................................7
NOTCH FILTER ............................................................................................................................7
ALLOW CARD ERASE .................................................................................................................7
DISPLAY ELAPSED TIME .............................................................................................................7
VOICE MARKERS ENABLED ........................................................................................................7
SET REPORT RESTART DELAYS ..................................................................................................8
PRINT 12 LEAD 4X3 ....................................................................................................................8
AUTO SELF-TEST TIMEOUT PERIOD ...........................................................................................8
ASYNC SOFTKEY IN PACE MODE ...............................................................................................8
CODE MARKERS ......................................................................................................................... 8
DEVICE IDENTIFIER ..................................................................................................................10
MANUAL MODE PASSCODE (ADVANCED AED MODELS) ........................................................11
CONFIGURATION MODE PASSCODE ..........................................................................................11
ENERGY LEVEL: SHOCK 1, 2, 3 ................................................................................................12
AUTO ANALYZE 3 TIMES ......................................................................................................... 12
"NO SHOCK ADVISED" PROMPT .........................................................................................12
"CHECK PATIENT" PROMPT .................................................................................................12
DISPLAY DO CPR MESSAGE ....................................................................................................12
DISPLAY ECG IN SEMI-AUTO MODE .......................................................................................12
STORE TO CARD IN AUTO MONITOR MODE (AED MODELS) ...................................................13
AUTO CHARGE IN ADVISORY MODE ........................................................................................13
RECORD TO CARD IN ADVISORY MODE ...................................................................................13
ENABLE VOICE INADVISORY MODE .......................................................................................13
DISPLAY HEART RATE IN SEMI-AUTO MODE ..........................................................................13
DISPLAY LEAD ON POWER-UP.................................................................................................13
FREQUENCY RESPONSE ............................................................................................................13
ENABLE 12-LEAD IN SEMI-AUTO MODE (AED WITH 12-LEAD) .............................................13
QRS VOLUME ON POWER-UP..................................................................................................13
PACE RATE SETTING ON POWER-UP........................................................................................14
DISPLAY IMPLANTED PACE SPIKES ..........................................................................................14
GAIN ONPOWER-UP................................................................................................................14
RETAIN SYNC AFTER DEFIB ....................................................................................................14
AUTO GENERATE STRIPS ..........................................................................................................14
PRINT 3 LEADS WHEN LEADS SEL ...........................................................................................14
REPORT MEMORY CARD ERRORS ............................................................................................14
AUTO ANALYZE ON POWER UP(AED SEMI-AUTOMATIC MODE) ..........................................14
AUTO TRANSMIT AFTER 12 LEAD ............................................................................................14
FAX/COMMUNICATION PHONE NUMBERS ................................................................................15
12 LEAD ANALYSIS ..................................................................................................................17
12 LEAD PRINTOUT ..................................................................................................................17
PRINT 12 LEAD MEASUREMENTS .............................................................................................17
12 LEAD FAX FORMAT .............................................................................................................17
PRINT 2 COPIES 12 LEAD .........................................................................................................17
SET LEAD GROUPS ...................................................................................................................18
12 LEAD FREQ RESPONSE ........................................................................................................18

M SERIES OPERATOR’SGUIDE
1-2
LEAD GROUP DEFAULT ............................................................................................................18
PRINT 12 LEAD INTERPRETATION ............................................................................................18
DEFIB DEFAULT TO PADS .........................................................................................................18
CELL PHONE TYPE ....................................................................................................................19
ETCO2 OPTIONS .......................................................................................................................19
ENABLE LEADS OFF .................................................................................................................19
BLOOD PRESSURE UNITS ..........................................................................................................19
NIBP AUTO INTERVAL DEFAULT .............................................................................................19
TRIGGER NIBP MEAS ON BP ALARM ......................................................................................19
TRIGGER NIBP MEAS ON HR ALARM .....................................................................................19
NIBP FIRST INFLATE PRESSURE DEFAULT ..............................................................................19
BASIC AUTO ENERGY ESCALATION .........................................................................................20
MUSE SITE AND LOCATION .....................................................................................................21
12 LEAD SECS PER LEAD .........................................................................................................21
12 LEAD PRINT SPEED ..............................................................................................................21
UPLOAD BAUD RATE ................................................................................................................21
TRENDING REPORT ZOOM LEVEL ............................................................................................21
TRENDING ENABLED ................................................................................................................22
AED DEFIB READY HOLD TIME (AED SEMI-AUTOMATIC MODE) .........................................22
BATTERY TYPE USED ...............................................................................................................22
ALARM LIMITS AT POWER UP..................................................................................................23
ALARMS ACTIVE AT POWER UP...............................................................................................23
LOW BATTERY TONE ................................................................................................................23
CLOCK SYNCHRONIZATION ......................................................................................................23
DAYLIGHT SAVINGS .................................................................................................................24
CARD CAPACITY MESSAGE ENABLED ......................................................................................24
ERASE CARD PROMPT AT PWR OFF .........................................................................................24
REMOVE CARD PROMPT AT PWR OFF ......................................................................................25
SYNC DEFIB EXCLUDED ...........................................................................................................25
PTCA SETTINGS .......................................................................................................................25
POWER UPPATIENT TYPE (NIBP) ...........................................................................................25
TEMPERATURE UNITS ...............................................................................................................26
DISPLAY COLORS .....................................................................................................................26
POWER UPTRACE SELECTION ..................................................................................................26
IBP1 LABEL AT POWER UP......................................................................................................27
IBP2 LABEL AT POWER UP......................................................................................................27
IBP1 RANGE AT POWER UP.....................................................................................................27
IBP2 RANGE AT POWER UP.....................................................................................................27
CONFIGURATION OPTION TABLES ........................................................................................29
GENERAL ..................................................................................................................................29
ADVISORY AND SEMI-AUTOMATIC MODES ..............................................................................31
MANUAL MODE ........................................................................................................................32
ETCO2 OPTION ........................................................................................................................33
NIBP OPTION ...........................................................................................................................33
PTCA SETTINGS OPTION ..........................................................................................................33
EXPANDED DISPLAY OPTION ....................................................................................................33
IBP OPTION ..............................................................................................................................34
TEMPERATURE OPTION ............................................................................................................34

1
Introduction
The M Series CCT is designed with several user selectable features that allow operators to
configure the device according to their protocols and local requirements. This manual describes
the configuration options and how to change them. This manual also lists the configurable
features, options and default settings. Some features are available to manual mode operators
only.
The default settings shown below are for North American units only. To print the current
configuration of your unit, while the unit is in the configuration mode, press the Print Config
softkey.
Configuring the Unit
After the unit has been off for 10 seconds or more, simultaneously press and hold the rightmost
and leftmost softkeys. Turn the selector switch to MONITOR or ON while holding the buttons
depressed for approximately four (4) seconds. After four (4) seconds the following screen will
appear.
Users entering System Configuration for the first time must enter the default passcode
(00000000) for System Configuration to continue.
Press the 0 (zero) softkey. This moves the highlight to the next digit. Repeatedly press the 0
(zero) softkey until all eight digits have been entered. The Configuration Passcode screen will
then automatically advance to the Select Language menu.
To change one of the entered digits use the Delete softkey to highlight the incorrect digit and
reenter the correct code.
CAUTION
The following features are not currently implemented on the M Series CCT: Voice Markers and
Auto Self-Test.
6\VWHP&RQILJXUDWLRQ



'HOHWH
(QWHU&RQILJXUDWLRQ3DVVFRGH
RU3RZHU2IIWR([LW
""""""""

MSERIES CCT CONFIGURATION GUIDE
2
Select Language
The first configurable option displayed after entering the correct pass code is the Select
Language option. Press the Prev Value and Next Value softkeys to move the highlight from
one language to the other.
Some M Series CCT units include software that allows the device to operate in either of two
languages. If the languages displayed do not meet your needs, contact ZOLL Technical Service
for a language upgrade.
Caution: Print out the summary report before changing languages. If a summary report
containing Code Marker events is printed after changing languages, the Code
Marker events will not match.
Press the Enter softkey to select the highlighted language and move to the Main Configuration
menu. All subsequent configuration menus will be in the selected language. Press the Exit
Config softkey to display the following three choices:
Press the Prev Item or Next Item softkey to scroll the highlight to the desired function. Press
the Enter softkey to activate the selected function.
If the Return to Main Menu is selected, the unit will then display the Select Language menu
described in the previous section.
6\VWHP&RQILJXUDWLRQ
3UHY
9DOXH
1H[W
9DOXH
(QWHU
6HOHFW/DQJXDJH
(1*/,6+
)5$1&$,6
([LW
&RQILJ
6\VWHP&RQILJXUDWLRQ
3UHY
,WHP
1H[W
,WHP (QWHU
6DYH&KDQJHVDQG([LW
'LVFDUG&KDQJHVDQG([LW
5HWXUQWR0DLQ0HQX

Configuring the Unit
3
Main Configuration Menu
The Main Configuration menu is displayed whenever the Enter softkey is depressed from the
Language Select menu or the Main Menu softkey is depressed while displaying other system
configuration screens.
This menu provides the following five (5) softkey options: Print Config, Restore Defaults,
Read From Card, Change Config, and Exit Config.
Print Config
Pressing the Print Config softkey will cause the unit to print the current unit configuration
settings.
Restore Defaults
Pressing the Restore Defaults softkey causes the unit to reconfigure to its default settings. (See
the “Configuration Option Tables” on page 29). The display language is the only setting that
will not revert to default. Once the default settings have been restored, the “Defaults Restored”
and “Press Change Config to View” messages are displayed.
6\VWHP&RQILJXUDWLRQ
5HVWRUH
'HIDXOWV
5HDG
)URP
&DUG
3ULQW
&RQILJ
&KDQJH
&RQILJ
([LW
&RQILJ
6\VWHP&RQILJXUDWLRQ
5HVWRUH
'HIDXOWV
5HDG
)URP
&DUG
3ULQW
&RQILJ
&KDQJH
&RQILJ
([LW
&RQILJ
'HIDXOWV5HVWRUHG
3UHVV&KDQJH&RQILJWR9LHZ

MSERIES CCT CONFIGURATION GUIDE
4
Read From Card
Pressing the Read From Card softkey prompts the user to choose either a language or
configuration card. The following screen will be displayed.
To move the highlighted area from LANGUAGE to CONFIGURATION and vice versa, press
the Prev Item and Next Item softkeys. Press the Enter softkey to begin reading and storing the
language settings or configuration settings from the user installed memory card.
If a language card has been read and loaded, the “Card Read” message displays. If a configura-
tion card has been read and loaded, the “Card Read” and “Press Change Config to View” mes-
sages display (see below):
If there is an error reading the memory card, one of the following error messages will be
displayed on the monitor.
EROR MESSAGE DEFINITION
CARD READ FAILED No response from card reader
BAD CARD Cannot read from card
WRONG CARD TYPE Card is the wrong type
CONFIG DATA NOT COMPATIBLE Internal software is unable to read card data
NO CARD INSERTED Card is not installed in PCMCIA slot
CARD EMPTY No data on card
6\VWHP&RQILJXUDWLRQ
3UHY
9DOXH
1H[W
9DOXH


(QWHU 
5HDG:KLFK7\SHRI&DUG"
/$1*8$*(
&21),*85$7,21
6\VWHP&RQILJXUDWLRQ
5HVWRUH
'HIDXOWV
5HDG
)URP
&DUG
3ULQW
&RQILJ
&KDQJH
&RQILJ
([LW
&RQILJ
&DUG5HDG
3UHVV&KDQJH&RQILJWR9LHZ

Configuring the Unit
5
Change Config
Pressing the Change Config softkey causes the unit to display the first configuration option
menu.
There are three user configurable features contained within each option menu. (Refer to the
“Configuration Option Tables” on page 29 for all available options and default settings).

MSERIES CCT CONFIGURATION GUIDE
6
(This page has intentionally been left blank.)

Configuration Settings
7
Configuration Settings
The name of each configurable feature is displayed in the left column of the option menu and
that feature’s current setting is shown in the right column.
Pressing the Change Value softkey allows you to sequence through the available settings for
the highlighted feature. When the desired setting is displayed, pressing the Next Item softkey
will enter the selection and move the highlight to the next feature. Pressing the Prev Item
softkey will enter the selected setting and move the highlight to the previously selected feature.
Pressing the Main Menu softkey will cause the unit to return to the Main Configuration menu.
Pressing the Exit Config softkey will cause the unit to display the “Save Changes and Exit”
screen.
NEXT MENU is displayed on the screen when other option menus are available. Press the Next
Item softkey until the new menu is displayed.
PREV MENU is displayed on the screen when other previously displayed option menus are
available. Press the Prev Item softkey until the previous menu is displayed.
Notch Filter
Sets the ECG Notch Filter frequency for proper AC mains interference rejection.
Allow Card Erase
Allows the user to erase PCMCIA data cards on the M Series CCT unit when set to “Yes”.
Display Elapsed Time
Allows the user to display the elapsed time since the unit was turned on, when enabled. The
elapsed time will continue to be counted for up to 10 seconds after power down. This will give
the operator adequate time to change the battery without resetting the elapsed timer.
Elapsed time will be reset to zero (0:00) whenever the unit has been off for more than 10
seconds.
Voice Markers Enabled
When voice markers are enabled, the unit will record five seconds of audio data in internal
memory immediately following each depression of the CODE MARKER button. This audio
recording along with a time stamp can be played back when the SUMMARY button is pressed.
Note: This option is not yet implemented.

6\VWHP&RQILJXUDWLRQ
3UHY
,WHP
1H[W
,WHP
&KDQJH
9DOXH
0DLQ
0HQX
127&+
),/7(5
$//2:
&$5'(5$6(
',63/$<
(/$36('7,0(
([LW
&RQILJ
+]
<HV
1R

MSERIES CCT CONFIGURATION GUIDE
8
Set Report Restart Delays
Allows review of, or changes to the length of time the device must be turned off before it erases
all data stored in either summary report memory or trend memory.
With Set Report Restart Delay highlighted and Set/Review selected, press the Change Value
softkey. The following screen displays:
Pressing the Change Value softkey will scroll the highlight through the available delay times.
Pressing the Prev Item and Next Item softkeys will scroll the highlight to the next or previous
restart delay feature.
Pressing the Enter softkey will cause the unit to return to the main configuration menu.
Print 12 Lead 4x3
Determines how many copies of a 12-lead 4x3 report will print after pressing and holding the
RECORDER button for three seconds. When set to “1 Copy” or “2 Copies” one or two copies
of the 12-lead 4x3 report will print. When set to “None”, pressing and holding the
RECORDER button will cause a one or three lead DIAG BANDWIDTH ECG strip to be
printed.
Auto Self-Test Timeout Period
Allows the user to set the time between tests or disable the automatic tests. The unit is capable
of automatically running a self-test at seven to thirty day intervals. If the unit is off, plugged in,
and the test connector is attached to the Multi-Function cable, the unit will test the battery
status, charge and discharge the defibrillator, measure the amplitude and timing of the pacing
waveform, and measure the impedance of the test port.
Note: This option is not yet implemented.
Async Softkey in Pace Mode
Sets the unit to display the Async Pacing On/Off softkey when the unit is in pace mode.
Code Markers
Allows review of or changes to the preconfigured list of Code Markers available for use in
PACER, MONITOR, and DEFIB modes.
Note: MONITOR Code Markers are not used in AED Models.

6\VWHP&RQILJXUDWLRQ
3UHY
,WHP
1H[W
,WHP
&KDQJH
9DOXH
6800$5<5(3257
5(67$57'(/$<
75(1'5(3257
5(67$57'(/$<
0,1
0,1
(QWHU
5(67$57'(/$<7,0(6

Configuration Settings
9
With Code Markers highlighted and Config/Review selected, press the Change Value softkey.
The following screen displays:
Pressing the Change Value softkey will change the highlighted setting from Change/Review to
Set to Defaults and vice versa.
Pressing the Prev Item and Next Item softkeys will scroll the highlight to the next or
previously highlighted code markers feature.
Pressing the Enter softkey when the Change/Review option is highlighted for one of the code
markers features causes the following screen to be displayed (this example shows the Defib
Code Markers screen).
Pressing the Change Value softkey will highlight the first clinical action in the Marker List
column and change the softkeys so that a new clinical action may be entered (shown below).
Pressing the Prev Marker and Next Marker softkeys scroll the highlight through the entire
Marker List. Press the Enter Marker softkey to replace the highlighted item in the Defib
markers column with the highlighted clinical action in the Marker List.
Pressing the Prev Item or Next Item softkeys will scroll the highlight to a different item
number in the Defib Markers column.
Pressing the Delete to End softkey will delete all configured Defib markers from the
highlighted item number to the end of the list. The user can then enter new clinical actions for
each item.
Pressing the Return softkey will return the unit to the Change/Review Code Markers display
where the user can choose Defib, Monitor or Pace Code Markers.
Pressing the Return softkey again causes the unit to return to the previous menu.
6\VWHP&RQILJXUDWLRQ
3UHY
,WHP
1H[W
,WHP
&KDQJH
9DOXH (QWHU
&KDQJH5HYLHZ
&KDQJH5HYLHZ
&KDQJH5HYLHZ

5HWXUQ
'(),%
&2'(0$5.(56
021,725
&2'(0$5.(56
3$&(
&2'(0$5.(56
6\VWHP&RQILJXUDWLRQ
3UHY
,WHP
1H[W
,WHP
&KDQJH
9DOXH
'HOHWHWR
(QG


&35
(3,
$WURS
'23$
,VRSURW
%LFDUE
$VSLULQ
2[\JHQ

5HWXUQ

,WHP&35
,WHP,QWXEDWH
,WHP(3,
,WHP/,'2
,WHP%5(7
,WHP%EORFN
,WHP$0,2
,WHP0DJ6XOI
'HILE0DUNHUV0DUNHU/LVW

MSERIES CCT CONFIGURATION GUIDE
10
Device Identifier
Sets an eleven-digit device identifier code. This code is divided into two sub codes (Site ID,
eight alphanumeric characters, and Device ID, three alphanumeric characters). The device
identifier is printed on the 12-lead strip chart, summary report, fax and Catalyst™MUSE®
printouts.
Note: If you are transmitting 12-lead ECG data to a Catalyst MUSE system, it is
recommended that you set up the device identifier.
Pressing the Change Value softkey causes the following screen to display:
Pressing the Prev Letter softkey moves the highlight left to the previous entered digit.
Pressing the Inc Letter or Dec Letter softkeys increments or decrements the selected digit.
Pressing the Next Letter softkey moves the highlight right to the next digit to be entered.
Pressing the Enter softkey selects the values that have been entered and returns to main
configuration menu.
6\VWHP&RQILJXUDWLRQ
,QF
/HWWHU
'HF
/HWWHU
3UHY
/HWWHU
1H[W
/HWWHU

(QWHU
6HW6LWH,'

6HW'HYLFH,'


Configuration Settings
11
Manual Mode Passcode (Advanced AED Models)
Allows the three-digit Manual Mode Passcode to be set or changed. Each digit entered can only
be set between 0 (zero) and 3 (three) inclusive.
Entering “000” as the pass code disables password protection of the Manual Mode. When “000”
is selected, no password is required to enter the Manual Defibrillation Mode.
Pressing the Change Value softkey causes the following screen to display:
Pressing the Prev Digit softkey moves the highlight left to the previous entered digit.
Pressing the Inc Digit or Dec Digit softkeys increments or decrements the selected digit.
Pressing the Next Digit softkey moves the highlight right to the next digit to be entered.
Pressing the Enter softkey selects the values that have been entered and returns to main
configuration menu.
Configuration Mode Passcode
Sets an eight digit Configuration Passcode. Each digit entered can only be set between 0 (zero)
and 3 (three) inclusive.
Pressing the Change Value softkey causes the following screen to display:
Pressing the Prev Digit softkey moves the highlight left to the previous entered digit.
Pressing the Inc Digit or Dec Digit softkeys increments or decrements the selected digit.
Pressing the Next Digit softkey moves the highlight right to the next digit to be entered.
Pressing the Enter softkey selects the values that have been entered and returns to main
configuration menu.
6\VWHP&RQILJXUDWLRQ
,QF
'LJLW
'HF
'LJLW
3UHY
'LJLW
1H[W
'LJLW

(QWHU
6HW0DQXDO3DVVFRGH

6\VWHP&RQILJXUDWLRQ
,QF
'LJLW
'HF
'LJLW
3UHY
'LJLW
1H[W
'LJLW

(QWHU
6HW&RQILJXUDWLRQ3DVVFRGH


MSERIES CCT CONFIGURATION GUIDE
12
Energy Level: Shock 1, 2, 3
Selects the energy levels used for the 1st, 2nd, and 3rd consecutive shocks that the defibrillator
delivers when:
•In semi-automatic or advisory mode and using pads
•Ιn manual mode, using external paddles or pads, with Basic Auto Energy Escalation set
to “Yes”
Energy level 1 is the energy level the unit defaults to when the power is turned on with external
paddles or pads connected. For more information about the Basic Auto Energy Escalation
setting, see the “Basic Auto Energy Escalation” section of this manual.
Auto Analyze 3 Times
Sets the unit to automatically repeat ECG rhythm analyses after the delivery of shocks in the
AED and Advisory Modes. When set to “Yes”, the unit automatically analyzes the patient’s
ECG rhythm after the first and second shocks in each three-shock sequence. Following delivery
of the third shock automatic reanalysis is halted and the “CHECK PULSE” message is
displayed. This indicates that the three shocks sequence has been completed and the patient's
pulse should be checked. This function only operates when the “Auto Charge in Advisory
Mode” configuration option is also enabled.
When set to “Only in Semi-auto,” the unit functions as described above only when it is in AED
semi-auto mode. If the unit is changed to Manual mode when set to “Only in Semi-auto”, any
automatic analysis/reanalysis sequencing terminates. If the Analyze button is pressed, the unit
analyzes only once.
"NO SHOCK ADVISED" Prompt
Changes the display message and the voice prompt issued after analysis of non-shockable
rhythm.
"CHECK PATIENT" Prompt
Changes the display message and the voice prompt issued when a shockable rhythm has been
detected by background ECG analysis and Heart Rate Alarms are enabled, or the unit is
operating in Semi-Automatic mode.
Display DO CPR Message
Sets unit to display messages “IF NO PULSE” / “PERFORM CPR” alternately for one minute
after each set of stacked shocks even if a perfusing rhythm is present.
ECG Rhythm analysis will restart automatically 70 seconds after delivery of the third shock in a
three-analysis/shock sequence. The “CHECK PATIENT” message and voice prompt will also
be inhibited for 70 seconds, following completion of a user activated analysis or discharge. This
feature is operational only when the “Auto Charge in Advisory Mode” and “Auto Analyze 3
times” configuration options are enabled.
When set to “Only in Semi-Auto,” the unit functions as described above only when it is in AED
semi-auto mode.
Display ECG in Semi-Auto Mode
Sets the device to display or not display the patient’s ECG trace on the monitor while in
semiautomatic mode.

Configuration Settings
13
Store to Card in Auto Monitor Mode (AED models)
Sets unit to automatically store patient’s ECG trace and voice data to the PCMCIA card when:
•ECG leads are attached to the patient
•MFE pads are not connected
•MSeries CCT unit is on
If disabled, the M Series CCT unit will not record any data to the PCMCIA card unless MFE
pads are connected to the patient.
Auto Charge in Advisory Mode
When enabled and a shockable rhythm is detected after pressing the ANALYZE button, the
unit will automatically charge the defibrillator to the pre-configured or user selected energy
setting.
Record to Card in Advisory Mode
Sets the unit to record ECG data (ECG only), ECG and voice data (Voice and ECG), or nothing
(None) to the memory card.
Enable Voice In Advisory Mode
Enables or disables voice prompts when operating in Advisory or Manual operating modes. If
enabled, the voice prompts will sound at the appropriate time when in Advisory mode or
Manual mode.
Display Heart Rate in Semi-Auto Mode
Sets the device to display or not display the patient heart rate on the monitor while in
semiautomatic mode.
Display Lead on Power-Up
Allows the user to select any one of the following Leads to be displayed on power-up: Paddles/
Pads, I, II, or III. When the unit powers up in semi-automatic mode, the option is ignored. The
unit will power up in Lead II, and switch leads automatically between leads II and MFE for
Auto Monitor and Auto Defib modes, respectively. When the unit enters Manual Mode (Manual
Mode override sequence is completed), the lead switches to the setting specified in the "Display
Lead on Power Up" option.
Frequency Response
Selects the ECG filter bandwidth to be used during ECG monitoring. The frequency of the
device can be set to either help reduce noise, help with the diagnostic response, or set as a
default response.
Enable 12-Lead in Semi-Auto Mode (AED with 12-Lead)
If set to “Yes,” 12-lead analyses, transmissions and print-outs are available in semi-automatic
(AED) Auto Monitor mode (ECG leads on the patient with MFE Pads disconnected), depending
on other configuration option settings. If set to “No,” 12-lead functions are available in Manual
Mode only.
QRS Volume on Power-Up
Turns the default QRS beeper volume to midrange or off following power up of the unit.
If set to “Off in Semi-Auto Mode,” the QRS beeper volume turns off in semi-auto mode. If the
unit is changed to manual mode, the beeper volume sets to midrange.

MSERIES CCT CONFIGURATION GUIDE
14
Pace Rate Setting on Power-Up
Sets the default pace rate of the M Series CCT unit on power-up, between 30 ppm and 102 ppm
(increments of 4 ppm).
Display Implanted Pace Spikes
The M Series CCT is capable of detecting and indicating on the display pacemaker signals from
a patient with an implantable pacemaker. Selecting “Yes” causes a pacemaker marker to be
displayed on the ECG trace whenever implanted pacer stimuli are detected. The pacemaker
spike detector is always active in ECG leads, independent of this configuration setting. This
setting controls spike display only.
Gain On Power-Up
Sets the default SIZE of the displayed ECG signal (AGC, 0.5 cm/mV, 1 cm/mV, 1.5 cm/mV,
and 2 cm/mV) when the device is powered-up.
Retain SYNC after Defib
Causes the unit to remain in SYNC mode after a synchronized cardioversion shock. The unit
will remain in SYNC mode until the SYNC button is pressed again or the unit is switched out of
Defib mode.
Auto Generate Strips
Sets the strip chart recorder to automatically begin printing after a defibrillator discharge or
whenever alarms are triggered while in manual mode. (Unit must be equipped with the optional
strip chart recorder feature.)
Print 3 Leads When Leads Sel
When enabled, the strip chart recorder will automatically print three (3) simultaneous leads of
the patient ECG when Leads are selected and a five (5) lead or 12-lead ECG cable is in use.
Report Memory Card Errors
Allows the user to disable memory card error messages and voice prompts.
If this option is set to "No", all error messages (i.e., “INSERT CARD", "REPLACE CARD",
"CARD FULL”, and “CARD LOW < nMINUTES”) related to the use of the memory card will
be suppressed. However, if the unit is in manual mode, or the unit is non-AED, the option is
ignored when the "Record to Card in Advisory Mode" option is set to "None" (no data
recording).
Auto Analyze on Power Up (AED Semi-Automatic Mode)
When set to “Yes”, the unit will automatically begin an ECG rhythm analysis as soon as the
device is turned on and pads are properly connected. An “ANALYZING ECG” message will be
displayed for 5 seconds and a “STAND CLEAR” message is displayed and announced
indicating the start of the analysis. If the Auto Analyze 3 Times option is enabled, the analysis
will be the first of a three analysis sequence.
Note: The unit must be turned off for 10 seconds or more for the analysis to auto -start when
the device is turned on.
Auto Transmit After 12 Lead
When enabled, the unit will automatically enter the transmission setup screen following
completion of a 12-lead analysis.
To fax using 2x6 format, this must be set to “Yes.”

Configuration Settings
15
Fax/Communication Phone Numbers
Allows the user to pre-configure up to 24 locations and phone numbers and delete obsolete
phone numbers. The M Series CCT uses the phone numbers to transmit data to a fax machine or
Catalyst MUSE system following 12-lead analysis.
If you are transmitting to a Catalyst MUSE system, you can configure multiple phone numbers
to access the same system. This will enable you to quickly try alternate numbers if you
encounter difficulty transmitting to the Catalyst MUSE system. The system administrator
provides these numbers when you initially set up access to the system. See Appendix B of the
12- Lead ECG Monitoring Operator’s Guide insert (part number 9650-0215-01) for more
information.
You must also configure the Catalyst MUSE site and location identifiers before you can
transmit to a Catalyst MUSE system. See “MUSE Site and Location” on page 21.
It is also recommended that you set up the M Series device identifier; see “Device Identifier” on
page 10.
Updating Fax/Communication Information
To transmit data to a fax machine or a Catalyst MUSE system, you must configure the
following:
•The location of the medical facility to which data will be transmitted
•The phone number to which data will be transmitted
•The type of data to be transmitted (“Fax” if transmitting to a fax machine; “Data” if
transmitting to Catalyst MUSE)
To update fax/MUSE communications phone numbers:
1. From the main System Configuration menu, press the Next Item softkey until “FAX/
COMMUNICATION PHONE NUMBERS” highlights.
2. Press Change Value softkey. The Phone Numbers menu displays:
3. Press Next or Prev softkey until either:
•The phone number to be changed highlights
•An empty line highlights (if adding a new phone number)
6\VWHP&RQILJXUDWLRQ
1H[W

'HOHWH
3UHY

'HWDLOV


5HWXUQ
0HWUR+RVSLWDO 
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBB
3+21(180%(56

MSERIES CCT CONFIGURATION GUIDE
16
4. Press Details softkey to select field. The Location and Phone Number menu displays:
To update location of medical facility:
1. Press Prev Letter or Next Letter softkey to select letter.
2. Press Inc Letter or Dec Letter softkey to change value of letter.
Repeat steps 1 and 2 until location has been entered.
3. Press Enter softkey to move cursor to first digit of phone number.
To update phone number:
1. Press Prev Letter or Next Letter softkey to select digit.
2. Press Inc Letter or Dec Letter softkey to change value of digit.
Repeat steps 1 and 2 until entire phone number has been entered.
3. Press Enter softkey to move cursor to “Fax or Data?” field.
To specify type of phone number:
1. Press Inc Letter softkey to toggle between “Fax” and “Data.” Select “Fax” to transmit to a
fax machine.
Select “Data” to transmit to a Catalyst MUSE system.
2. Press Enter softkey.
6\VWHP&RQILJXUDWLRQ
,QF
/HWWHU
'HF
/HWWHU
3UHY
/HWWHU
1H[W
/HWWHU

(QWHU
/RFDWLRQ
3KRQH1XPEHU
BBBBBBBBBBBBBBBBBBBBBBBBBBB
)D[RU'DWD")D[
,QF
/HWWHU
'HF
/HWWHU
3UHY
/HWWHU
1H[W
/HWWHU

(QWHU
)D[RU'DWD")D[
,QF
/HWWHU
'HF
/HWWHU
3UHY
/HWWHU
1H[W
/HWWHU

(QWHU
)D[RU'DWD"'DWD