Zte ZXHN H1600 Programming manual

ZXHN H1600
Home Gateway
Maintenance Management Guide
Version:V1.0
ZTE CORPORATION
No. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Tel: [phone]
URL: http://support.zte.com.cn
E-mail: [email protected]

LEGAL INFORMATION
Copyright 2021 ZTE CORPORATION.
The contents of this document are protected by copyright laws and international treaties. Any reproduction
or distribution of this document or any portion of this document, in any form by any means, without the
prior written consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document
are protected by contractual confidentiality obligations.
All company, brand and product names are trade or service marks, or registered trade or service marks,
of ZTE CORPORATION or of their respective owners.
This document is provided as is, and all express, implied, or statutory warranties, representations or
conditions are disclaimed, including without limitation any implied warranty of merchantability, fitness for
a particular purpose, title or non-infringement. ZTE CORPORATION and its licensors shall not be liable
for damages resulting from the use of or reliance on the information contained herein.
ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applica-
tions covering the subject matter of this document. Except as expressly provided in any written license
between ZTE CORPORATION and its licensee, the user of this document shall not acquire any license
to the subject matter herein.
ZTE CORPORATION reserves the right to upgrade or make technical change to this product without
further notice.
Users may visit the ZTE technical support website http://support.zte.com.cn to inquire for related infor-
mation.
The ultimate right to interpret this product resides in ZTE CORPORATION.
Statement on the Use of Third-Party Embedded Software:
If third-party embedded software such as Oracle, Sybase/SAP, Veritas, Microsoft, Vmware, and Redhat
is delivered together with this product of ZTE, the embedded software must be used as only a component
of this product. If this product is discarded, the licenses for the embedded software must be void either
and must not be transferred. ZTE will provide technical support for the embedded software of this product.
Revision History
Revision No. Revision Date Revision Reason
R1.0 2021-03-04 First edition
Serial Number: SJ-20200218145027-006
Publishing Date: 2021-03-04(R1.0)

Contents
1 Safety Precautions....................................................................................1-1
2 Product Overview......................................................................................2-1
2.1 Package Check..................................................................................................... 2-2
2.2 Product Specifications...........................................................................................2-2
2.3 Hardware Description............................................................................................2-3
2.4 Hardware Connection........................................................................................... 2-9
3 Configuration Preparation........................................................................3-1
3.1 Configure TCP/IP.................................................................................................. 3-1
3.2 Login......................................................................................................................3-2
4 Topology.................................................................................................... 4-1
5 Configure the Internet.............................................................................. 5-1
5.1 Check the Status.................................................................................................. 5-1
5.1.1 Check the DSL Link Status......................................................................5-1
5.1.2 Check the DSL Connection Status.......................................................... 5-2
5.1.3 Check the Ethernet Interface Information................................................ 5-3
5.1.4 Check the Ethernet Connection Status....................................................5-3
5.1.5 Check the 3G Status............................................................................... 5-4
5.2 Configure the WAN............................................................................................... 5-5
5.2.1 Configure the DSL Connection................................................................ 5-5
5.2.2 Configure the Ethernet Connection........................................................5-10
5.2.3 Configure the 3G....................................................................................5-13
5.3 Configure the QoS.............................................................................................. 5-17
5.3.1 Configure the QoS Global Parameters.................................................. 5-17
5.3.2 Configure the QoS Classification........................................................... 5-17
5.3.3 Configure the QoS Congestion Management........................................ 5-19
5.3.4 Configure the QoS Traffic Shaping........................................................5-21
5.4 Configure the Security........................................................................................ 5-22
5.4.1 Configure the Firewall Level.................................................................. 5-22
5.4.2 Configure the Filter Criteria....................................................................5-23
5.4.3 Configure the Local Service Control...................................................... 5-26
5.4.4 Configure the ALG................................................................................. 5-29
5.4.5 Configure the DMZ.................................................................................5-30
5.4.6 Configure the Port Forwarding...............................................................5-31
I

5.5 Configure the Parental Controls......................................................................... 5-32
5.6 Configure the DDNS........................................................................................... 5-34
5.7 Configure the SNTP............................................................................................5-35
5.8 Configure the Port Binding..................................................................................5-36
5.9 Configure the Mulitcast....................................................................................... 5-36
5.9.1 Configure the IGMP............................................................................... 5-36
5.9.2 Configure the MLD.................................................................................5-37
6 Configure the Local Network...................................................................6-1
6.1 Check the Local Network Status.......................................................................... 6-1
6.2 Configure the WLAN............................................................................................. 6-2
6.2.1 Configure the Basic Parameters of the WLAN........................................ 6-2
6.2.2 Configure the Advanced Parameters of the WLAN................................. 6-5
6.3 Configure the LAN................................................................................................ 6-7
6.3.1 Configure the LAN(IPv4).......................................................................... 6-7
6.3.2 Configure the LAN(IPv6)........................................................................ 6-10
6.4 Configure the Route............................................................................................6-15
6.4.1 Configure the Routing(IPv4)...................................................................6-15
6.4.2 Configure the Routing(IPv6)...................................................................6-17
6.5 Configure the FTP...............................................................................................6-20
6.6 Configure the UPnP............................................................................................ 6-21
6.7 Configure the DMS/DLNA...................................................................................6-21
6.8 Configure the Samba Service.............................................................................6-22
6.9 Configure the DNS..............................................................................................6-23
6.10 Configure the Device Role................................................................................6-24
7 Configure the VoIP....................................................................................7-1
7.1 Check the Status of VoIP..................................................................................... 7-1
7.2 Configure the SIP Accounts..................................................................................7-2
7.3 Configure the Advanced Parameters....................................................................7-2
7.4 Configure the SIP Protocol................................................................................... 7-4
7.5 Configure the Media..............................................................................................7-5
7.6 Configure the Fax................................................................................................. 7-6
8 Configure the Management and Diagnosis............................................ 8-1
8.1 Configure the Account Management.................................................................... 8-1
8.2 Configure the Login Timeout................................................................................ 8-3
8.3 Configure the System Management..................................................................... 8-3
8.3.1 Configure the Device Management......................................................... 8-3
8.3.2 Upgrade Software.................................................................................... 8-4
II

8.3.3 Manage the User Configuration............................................................... 8-5
8.4 Configure the Mirror function................................................................................ 8-6
8.5 Configure the TR069 function...............................................................................8-7
8.6 Manage the Log....................................................................................................8-9
8.7 Diagnosis.............................................................................................................8-12
8.8 Check the ARP Table......................................................................................... 8-14
8.9 Check the MAC Table........................................................................................ 8-14
8.10 Configure the IPv6 Switch................................................................................ 8-15
9 Troubleshooting........................................................................................ 9-1
III

Chapter 1
Safety Precautions
Note
Before using the device, read the following safety precautions. ZTE bears no liability to
the consequences incurred by violation of the safety instructions.
Usage Cautions
Read all the safety cautions carefully before using the device.
Only use the accessories included in the package, such as power supply adapter.
Do not extend the power cord, otherwise the device will not work.
The power supply voltage must meet the requirements of the device input voltage (
The voltage fluctuation range is less than 10%).
Keep the power plug clean and dry to prevent any risk of electric shock or other dan-
gers.
Disconnect all the cables during a lightning storm to prevent the device from dam-
age.
Power off and unplug the power plug when the device is not in use for a long time.
Do not attempt to open the covers of the device. It is dangerous to do so when the
device is powered on.
Power off and stop using the device under the conditions such as, abnormal sound,
smoke, and strange smell. Contact the service provider for maintenance if the device
is faulty.
Environment Requirements
Ensure proper ventilation to the device. Place the device away from direct sunlight.
Keep the device ventilated and dry. Never spill any liquid on the device.
Do not place any object on the device to prevent any deformation or damage to the
device.
Do not place the device near any source of heat or water.
SJ-20200218145027-006 | 2021-03-04(R1.0) 1-1

ZXHN H1600 Maintenance Management Guide
Keep the device away from any household appliances with strong magnetic or elec-
tric fields, such as microwave oven and refrigerator.
Cleaning Requirements
Before cleaning, power off the device, and unplug all the cables connected to the de-
vice, such as power cable, optical fiber, and Ethernet cable.
Do not use any liquid or spray to clean the device. Use a soft dry cloth.
Environment Protection
Do not dispose the device or battery improperly.
Observe the local regulations about the equipment disposal or treatment.
Restrictions in the 5 GHz Band
According to Article 10(10) of Directive 2014/53/EU, the packaging shows that this ra-
dio equipment will be subject to some restrictions when placed on the market in Bel-
gium(BE), Bulgaria(BG), the Czech Republic(CZ), Denmark(DK), Germany(DE), Esto-
nia(EE), Ireland(IE), Greece(EL),Spain(ES), France(FR), Croatia(HR), Italy(IT),Cyprus(
CY), Latvia(LV), Lithuania(LT), Luxembourg(LU), Hungary(HU), Malta(MT), Nether-
lands(NL), Austria(AT), Poland(PL), Portugal(PT), Romania(RO), Slovenia(SI), Slo-
vakia(SK), Finland(FI), Sweden(SE), Turkey(TR), Norway(NO), Switzerland(CH), Ice-
land(IS), and Liechtenstein(LI).
The WLAN function for this device is restricted to indoor use only when operating in the
5150 to 5350 MHz frequency range.
RF Exposure Information
The Maximum Permissible Exposure (MPE) level is calculated based on a distance of
d=20 cm between the device and the human body. To maintain compliance with the RF
exposure requirement, a separation distance of 20 cm between the device and the hu-
man should be maintained.
EU Declaration of Conformity
Hereby, ZTE Corporation declares that the radio equipment type ZXHN H1600 is in
compliance with Directive 2014/53/EU, The full text of the EU declaration of conformity
is available at the following Internet address:
http://support.zte.com.cn/support/cer/EU
1-2 SJ-20200218145027-006 | 2021-03-04(R1.0)

1 Safety Precautions
Environmental Information
The equipment you purchased has required the extraction and use of natural resources
for its production. It may contain substances that are hazardous to people's health and
to the environment. To avoid putting such substances into our environment and to re-
duce pressure on our natural resources, we ask that you reuse or recycle your end-of-
life equipment by using an accredited electronics take-back system.
The symbols below indicate that this product should be reused or recycled and not sim-
ply discarded. Please locate and use an appropriate reuse and recycling site.
If you need more information on collection, reuse and recycling systems, contact your lo-
cal or regional waste administration. You may also contact your equipment provider for
more information on the environmental performances of these products.
SJ-20200218145027-006 | 2021-03-04(R1.0) 1-3

Chapter 2
Product Overview
Table of Contents
Package Check.............................................................................................................. 2-2
Product Specifications....................................................................................................2-2
Hardware Description.....................................................................................................2-3
Hardware Connection.................................................................................................... 2-9
The ZXHN H1600 is an advanced home gateway that supports Dual-band concurrent 11
ac Wi-Fi. It provides High Speed Internet, IPTV services through the GE uplink. Those
services are delivered by the gateway on your home network to the PCs, STBs, gaming
devices and so on via the integrated interfaces: Ethernet, Wi-Fi.
It supports the following features:
Gigabit Ethernet WAN Uplink
The ZXHN H1600 can provide Internet access through Gigabit Ethernet WAN con-
nection. So it is possible for ZXHN H1600 to provide Internet access choices to suit
various broadband access network.
GE LAN Ports
The ZXHN H1600 is equipped with 2 Gigabit Ethernet LAN interfaces which provides
higher bandwidth and speed for networking and makes the device more future-proof.
Dual Band Concurrent Wi-Fi
The ZXHN H1600 supports Dual-Band concurrent Wi-Fi up to 300Mbps(802.11n 2x2
@ 2.4GHz) and 1.7Gbps(802.11ac 4x4 @5GHz). Wi-Fi is a key feature for the
end users to build up a home network without any cabling in the house or in the of-
fice.
IPv4 / IPv6 Dual Stack
The ZXHN H1600 supports IPv4 / IPv6 dual stack mechanism for IPv6 network mi-
gration.
Remote management
The ZXHN H1600 supports TR-069, including TR-098 data model. It is convenient
for operators to facilitate the large-scale deployment and maintenance by zero-touch
provisioning.
SJ-20200218145027-006 | 2021-03-04(R1.0) 2-1

ZXHN H1600 Maintenance Management Guide
2.1 Package Check
Please ensure the ZXHN H1600 package contains the following items.
Name Quantity
ZXHN H1600 1
Power Adapter 1
RJ-45 Ethernet Cable 1
RJ-11 Telephone Cable 2
User Manual 1
Note
The list is only for reference. The actual contents may vary from the list.
If any of the items included in the package is incorrect, lost or damaged, please contact
your service provider. If you need to replace the product, please keep the package and
all the items in good condition.
2.2 Product Specifications
Table 2-1 describes the product specification of the ZXHN H1600.
Table 2-1 Product Specification
Technical Specifications
Dimensions 226 mm (H) × 32 mm (D) × 156 mm (W)
Input: AC 100 V – 240 V, 50 Hz/60 HzPower adapter
Output: DC 12.0 V, 2.0 A
Environment Requirements
Operation temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage temperature –40 °C to 70 °C (–40 °F to 158 °F )
Operation humidity/
Storage humidity 5% – 95% (non-condensing)
Wi-Fi Radio Specifications
Radio Frequencies Maximum Output Power
Wi-Fi 2.4 GHz band:
2400 MHz–2483.5 MHz
EIRP: 20 dBm
2-2 SJ-20200218145027-006 | 2021-03-04(R1.0)

2 Product Overview
Wi-Fi 5 GHz band:
5150 MHz–5250 MHz
EIRP: 23 dBm
Wi-Fi 5 GHz band:
5250 MHz–5350 MHz
EIRP: 23 dBm
Wi-Fi 5 GHz band:
5470 MHz–5725 MHz
EIRP: 30 dBm
2.3 Hardware Description
Front Panel
Figure 2-1 shows the indicators on the front panel of the ZXHN H1600
SJ-20200218145027-006 | 2021-03-04(R1.0) 2-3

ZXHN H1600 Maintenance Management Guide
Figure 2-1 The Front Panel
Table 2-2 describes the indicators on the front panel of the ZXHN H1600 unit.
Table 2-2 Descriptions of Indicators
LED Indicator Status Description
Off The device is powered off.
Solid green The device is powered on properly.
Power
Solid red The device is performing self-detection or the self-detec-
tion fails.
2-4 SJ-20200218145027-006 | 2021-03-04(R1.0)

2 Product Overview
LED Indicator Status Description
Off The DSL connection has not been established.
Solid green DSL synchronization is normal and the link Connection
is normal.
Flashing slowly green Physical link exists, however carrier wave has not been
detected.
Broadband
(DSL)
Flashing fast green The device is in the handshaking process to establish
the link connection.
Off The equipment is not powered on or the WAN port is
disabled.
Broadband
(WAN)
Solid green The Ethernet connection has been established.
Off The gateway is switched off.
Solid green
The WAN connection is online. The device has a WAN
IP address from IPCP, DHCP or statically configured.
LED remains green in the case of disconnection due
to idle timeout when PPP dial-on-demand is enabled.
Green LED indicates that the routing connection state is
up.
Solid red
The WAN connection is dialing up or fails to get online.
Device attempted to become IP connected and failed (
no DHCP response, no PPPoE response, PPP authenti-
cation failed, no IP address from IPCP, etc).
Internet
Flashing green The Internet connection has been established and the
data is being transmitted or received.
Off WLAN RF switch is off.
Solid green WLAN RF switch is on.
2.4G
Flashing green
WLAN RF switch is on and the data is being transmitted
or received, and the flashing frequency indicates Wi-Fi
network traffic.
Off WLAN RF switch is off.
Solid green WLAN RF switch is on.
5G
Flashing green
WLAN RF switch is on and the data is being transmitted
or received, and the flashing frequency indicates Wi-Fi
network traffic.
WPS Off No WPS access or the WPS access of the terminal ex-
ceeds 5 minutes.
SJ-20200218145027-006 | 2021-03-04(R1.0) 2-5

ZXHN H1600 Maintenance Management Guide
LED Indicator Status Description
Solid green WPS access is successful. This solid-on light will be au-
tomatically off after 5 minutes.
Flashing slowly green WLAN terminal is in WPS accessing process.
Flashing fast green The WPS accessing of the WLAN terminal is faulty.
Off The device is powered off or the USB interface is not
connected.
Solid green The USB interface is connected with USB device.USB
Flashing green Data is being transmitted or receivedvia the USB inter-
face.
Off The device has not been registered to the VOIP net-
work.
Solid green The device has registered to the VOIP network.
PHONE1
PHONE2
Flashing green The associated telephone is off-hook.
Off The LAN connection has not been established.
Solid green The LAN connection has been established.LAN1\LAN2\
LAN3\LAN4
Flashing green Data transmission is in processing, The indicator flashes
according to the LAN traffic.
The LAN1\LAN2\LAN3\LAN4 status indicator is on the LAN1\LAN2\LAN3\LAN4 port of the ZXHN
H1600.
Top Panel
Figure 2-2 shows the buttons on the top panel of the ZXHN H1600.
Figure 2-2 The Top Panel
Table 2-3 describes the buttons on the top panel of the ZXHN H1600.
2-6 SJ-20200218145027-006 | 2021-03-04(R1.0)

2 Product Overview
Table 2-3 Descriptions of the Top Panel
Button Function
Reset Reset push button. During power on period, press this button for more
than 5 seconds to reset the current settings to the factory default.
LED LED control button: Press the button to turn off all the indicators on the
panel. To turn on the indicators, press the button again.
WPS WPS Push Button, press this button to enable or disable the WPS func-
tion.
WiFi Wi-Fi dual-interfaces on/off button.
Side Panel
Figure 2-3 shows the buttons on the side panel of the ZXHN H1600.
SJ-20200218145027-006 | 2021-03-04(R1.0) 2-7

ZXHN H1600 Maintenance Management Guide
Figure 2-3 The Side Panel
Table 2-4 describes the interfaces and buttons on the side panel of the ZXHN H1600.
Table 2-4 Descriptions of the Side Panel
Interface/Button Function
DSL RJ-11 port. It is used to connect to the ADSL, VDSL or VDSL uplink ac-
cess network.
WAN RJ-45 port. It is used to connect to the uplink Ethernet access network.
LAN1\LAN2\
LAN3\LAN4
RJ-45 port. It is used to connect the modem to computer, STBs or other
network devices.
2-8 SJ-20200218145027-006 | 2021-03-04(R1.0)

2 Product Overview
Interface/Button Function
USB Standard USB 2.0 interface, connected to a USB storage device, printer or
3GDongle connection.
PHONE1
PHONE2 RJ-11 port. It is used to connect to the phone through the telephone line.
Power Power supply port. It is connected to the power adapter.
On/Off Power switch. Power on or power off the device.
2.4 Hardware Connection
Figure 2-4 shows the devices that are connected to interfaces of the ZXHN H1600
Figure 2-4 Cable Connection
After the devices are connected to the ZXHN H1600 device, press the power button.
When the corresponding indicators on the front panel are On, you can enjoy various ser-
vices provided by the service provider.
The factors affecting the wireless network coverage range include the location of the
product, distance between the product and a wireless terminal, number of obstacles, ob-
stacle material and density, and interference source. It is recommended that you place
SJ-20200218145027-006 | 2021-03-04(R1.0) 2-9

ZXHN H1600 Maintenance Management Guide
the product in accordance with the following principles to maximize the strength of wire-
less signals.
The product should be far away from the objects affecting wireless signal propaga-
tion, for example, an object with a high reflectivity such as a metallic object or a mir-
ror.
The product should be far away from an electrical appliance with a strong magnet-
ic or electric field, for example, a microwave oven, a refrigerator, a wireless router, a
cordless phone, or a Bluetooth product.
The product should be installed on the same floor as the applied area.
Do not put other objects on the product. Try to reduce the number of obstacles be-
tween the product and a wireless terminal.
Horizontally place the product in the middle of the applied area and do not put it in a
corner.
Do not place the product at a high position while it is placed horizontally. The recom-
mended height is 1.2 to 1.5 meters.
2-10 SJ-20200218145027-006 | 2021-03-04(R1.0)

Chapter 3
Configuration Prepara-
tion
Table of Contents
Configure TCP/IP........................................................................................................... 3-1
Login...............................................................................................................................3-2
This manual uses the Windows operating system as an example for describing how to
configure the ZXHN H1600. Before configuring the ZXHN H1600, you need to perform
the following operations:
Ensure that a crossover or straight-through Ethernet cable connects a computer to
the device.
Ensure that the TCP/IP configuration on the computer is correct.
Stop any firewall or other security software operating on the computer.
Disable the proxy setting of Internet Explorer.
3.1 Configure TCP/IP
To log in to the ZXHN H1600 on a computer, you need to set the IP address of the com-
puter to ensure that the IP address of the computer and the maintenance IP address of
the ZXHN H1600 are in the same network segment.
Context
The default maintenance IP address of the ZXHN H1600 is as follows:
IP address: 192.168.1.1
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1
Steps
1. Use an Ethernet cable to connect a local computer to the LAN interface of the ZXHN
H1600.
2. On the local computer, double-click Local Area Connection and click Properties.
The Local Area Connection Properties dialog box is displayed.
SJ-20200218145027-006 | 2021-03-04(R1.0) 3-1

ZXHN H1600 Maintenance Management Guide
3. Double-click Internet Protocol (TCP/IP). The Internet Protocol (TCP/IP) Proper-
ties dialog box is displayed. Set the IP address to 192.168.1.200, subnet mask to
255.255.255.0, and default gateway to 192.168.1.1.
4. Click OK.
Postrequisite
After the IP address of the computer is set, you can run the Ping command to ping the
IP address 192.168.1.1. If the ping operation is successful, it indicates that the TCP/IP
configuration is correct and the computer is properly connected to the ZXHN H1600.
3.2 Login
The ZXHN H1600 provides a Web-based configuration and management system. You
can enter a specified IP address in the address bar of Internet explorer to access the
system.
Prerequisite
A computer is directly connected to the LAN port of ZXHN H1600, and their IP address-
es are in the same network segment.
Steps
1. Open Internet explorer, and enter http://192.168.1.1 (default maintenance IP address
of the ZXHN H1600) in the address field. Press the Enter key. The login page is dis-
played, see Figure 3-1.
Figure 3-1 Login Page
3-2 SJ-20200218145027-006 | 2021-03-04(R1.0)