3One data IES615-2DI Series User manual

IES615-2DI series
Managed Industrial Ethernet Switches
CLI user manual
Version 1.0.0, Aug. 2017
www.3onedata.com

CLI user manual
- 1 -
IES615-2DI series CLI user manual
Statement
Copyright Notice
Information in this document is reserved by 3onedata Co., Ltd. Reproduction and
extract without permission is prohibited.
Trademarks Notice
, and is registered trademarks of
3onedata Co.,Ltd. All other trademarks or registered marks in this manual belong to
their respective manufacturers.
Agreement
As the product version upgrades or other reasons, this document is subject to
change without notice. Unless other agreement, this document only as a guide to
use. All statement, information and suggestion in this document, without warranty of
any kind, either expressed or implied.
Revision History
Version No.
Date
Reason
V1.0.0
August, 2017
Creating Documents
Notes
In reading this manual, please pay attention to the following symbols,
Information necessary to explain
Special attention

CLI user manual
- 2 -
Content
Chapter 1 Login Ethernet Switch......................................................................................................................... 1
1.1 Configuration through console port............................................................................................................ 1
1.2 Configuration through Telnet...................................................................................................................... 4
1.3 Agreement ................................................................................................................................................. 5
1.4 Command line port .................................................................................................................................... 6
1.4.1 View of Command Lines..................................................................................................................... 6
1.4.2 Command lines Online help................................................................................................................ 7
1.4.3 Frequent Incorrect Information of Command Lines............................................................................ 8
1.4.4 History command................................................................................................................................ 8
1.4.5 General Command.............................................................................................................................. 9
CHAPTER 2 Device system based information configuration .......................................................................... 10
2.1 Enter into the view of device information................................................................................................. 10
2.2 Display device information....................................................................................................................... 10
2.3 Configuration information..........................................................................................................................11
2.4 Delete device information.........................................................................................................................11
Chapter 3 Serial Configuration .......................................................................................................................... 13
3.1 Enter into serial configuration view.......................................................................................................... 13
3.2 Display serial information......................................................................................................................... 14
3.3 Clear serial incorrect information............................................................................................................. 17
3.4 Serial parameter configuration................................................................................................................. 17
3.5 Working mode parameter configuration................................................................................................... 18
Chapter 4 Port Configuration............................................................................................................................. 23
4.1 Port information........................................................................................................................................ 23
4.2 Display port configuration information ..................................................................................................... 23
4.3 Port configuration..................................................................................................................................... 24
4.4 To enable or disable the port ................................................................................................................... 24
4.5 Configure the port speed and duplex mode ............................................................................................ 24
4.6 Configure the port flow control................................................................................................................. 25
Chapter 5 Bandwidth Management................................................................................................................... 26
5.1 Enter rate management view................................................................................................................... 26
5.2 Enable and Disable Bandwidth................................................................................................................ 26
5.3 Egress bandwidth configuration............................................................................................................... 26
5.4 Ingress bandwidth configuration.............................................................................................................. 27
5.5 Displays the bandwidth configuration information ................................................................................... 27
Chapter 6 IGMP................................................................................................................................................. 28
6.1 The contents of IGMP configuration ........................................................................................................ 28
6.2 IGMP snooping mode enable .................................................................................................................. 28

CLI user manual
- 3 -
6.3 IGMP query mode enable........................................................................................................................ 28
6.4 Set IGMP query time................................................................................................................................ 29
6.5 Check the MAC address table................................................................................................................. 29
Chapter 7 VLAN................................................................................................................................................. 30
7.1 Introduction to VLAN................................................................................................................................ 30
7.2 The contents of VLAN configuration........................................................................................................ 30
7.3 Vlan information view............................................................................................................................... 31
7.4 VLAN Enable ........................................................................................................................................... 31
7.5 Enter the port configuration view based on Port-VLAN........................................................................... 32
7.6 Enter configuration view based on 802.1QVlan ...................................................................................... 32
Chapter 8 Static Multicast filtering view............................................................................................................. 34
8.1 Enter the multicast filtering view.............................................................................................................. 34
8.2 Add /Delete static multicast address........................................................................................................ 34
8.3 Configuration of showing static multicast address................................................................................... 35
Chapter 9 QoS................................................................................................................................................... 36
9.1 Enter the multicast filtering view.............................................................................................................. 36
9.2 Enable Dscp / Cos................................................................................................................................... 36
9.3 QoS queue configuration......................................................................................................................... 37
9.4 The value of Dscp/Tos mapping.............................................................................................................. 37
9.5 The default port priority allocation............................................................................................................ 37
9.6 Qos configuration information.................................................................................................................. 38
Chapter 10 Ring configuration........................................................................................................................... 40
10.1 Enter the ring network configuration view.............................................................................................. 40
10.2 Ring network state information view...................................................................................................... 40
10.3 To enable or disable the ring................................................................................................................. 41
10.4 The Ring3 configuration......................................................................................................................... 41
10.7 The RSTP configuration ........................................................................................................................ 42
10.8 Show RSTP information ........................................................................................................................ 44
Chapter 11 Trunk configuration......................................................................................................................... 45
11.1 Enter the port Trunk view....................................................................................................................... 45
11.2 Port trunk configuration / delete............................................................................................................. 45
11.3 Display port trunk configuration information .......................................................................................... 45
Chapter 12 The SNMP configuration................................................................................................................. 47
12.1 Configure the view into the SNMP......................................................................................................... 47
12.2 Enable the SNMP information ............................................................................................................... 47
12.3 The SNMP configuration view ............................................................................................................... 47
Chapter 13 Alarm configuration......................................................................................................................... 49
13.1 Enter the alarm information view........................................................................................................... 49
13.2 Alarm configuration / delete................................................................................................................... 49

CLI user manual
- 4 -
13.3 Display the alarm information................................................................................................................ 50
Chapter 14 Port Statistics.................................................................................................................................. 51
14.1 Enter the port statistical configuration view........................................................................................... 51
14.2 Port Statistics configuration view........................................................................................................... 51
Chapter 15 Port mirroring.................................................................................................................................. 53
15.1 Enter the port mirroring view.................................................................................................................. 53
15.2 Port mirroring configuration / delete ...................................................................................................... 53
15.3 Display port mirroring information.......................................................................................................... 54
Chapter 16 System management...................................................................................................................... 55
16.1 Enter the System management configuration view............................................................................... 55
16.2 System timeout...................................................................................................................................... 55
16.3 IP address and default gateway setting................................................................................................. 56
16.4 User name, password settings .............................................................................................................. 56
16.5 Display device IP, subnet mask, default gateway.................................................................................. 57
16.6 Restore factory settings......................................................................................................................... 57
16.7 The address of the DNS server settings................................................................................................ 57
16.8 Obtain an IP address automatically set................................................................................................. 58
16.9 Upload, download the configuration file................................................................................................. 58
16.10 The system upgrade............................................................................................................................ 59

CLI user manual
1
Chapter 1 Login Ethernet Switch
1.1 Configuration through console port
1. Connection switches to configure terminal
As shown in Figure 1.1.1, the establishment of the local configuration environment, only the
computer serial cable and connected to the Console port of the Ethernet switch.
(Figure 1.1.1)
This cable is used for connecting the switch Console port and the external monitoring
terminal equipment. One end is RJ45 eight core plug, the other end is the 9 hole plug (DB9).
Console RJ45 the switch socket head, the cable inner connecting line diagram as shown
below.
(Figure 1.1.2)
2. Configure terminal parameters
1) Turn the computer, on the Windows interface, click "Start/All
Programs/Accessories/communication", run a terminal emulation program to create a new
connection. The RS-232 port is connected to the computer. To take Hyper Terminal in
Windows XP for example, as shown in Figure 1.1.3, type in a new name of the connection in
a text box named "name", then click "OK" button.

CLI user manual
2
(Figure 1.1.3)
2) Choose connecting serial port. Choose connecting serial port under “Connect using”（pay
attention to the chosen serial port is consistent with the port connected with the configuration
cable）， Click “OK”. As shown in Figure 1.1.4.
(Figure 1.1.4)
3) Set serial port parameters. As shown in Figure 1.1.5, set the “Bits per second” in the
“Properties” of serial port is 115200bit/s，“Data bits” is 8，“parity” is None，“Stop Bits” is
1，“Flow Control” is None. Click “OK” button to enter to “Hyper Terminal” Window.

CLI user manual
3
(Figure 1.1.5)
4) Hyper terminal attribute. In the Hyper Terminal window select [document / property /
setting] into the attributes settings window. Select the terminal simulation of type VT100 or
automatic detection, click < OK > button to return to the hyper terminal window.
(Figure 1.1.6)

CLI user manual
4
5) For the switch power, power after the hyper terminal display Ethernet switch self-test
information, after the prompt the user to type the carriage return, until the emergence of
<user name> command prompt, this time to enter the correct username and password, enter
the switch system mode can be configured, the specific configuration commands refer to the
later chapters of the contents of the book in.
As the network pipeline connection than COM1, in step two must choose the corresponding COM port. Step three
"bits per second" must choose 115200, otherwise cannot be displayed.
1.2 Configuration through Telnet
Terminal device use telnet connect to the switch through PC, the requirements are as
follows:
1. The IP address of the switch can get it by search or modify (Use IP command under the
system management view);
2. If PC and the switch in the same local area network, the IP address must in a same
network segment, otherwise, PC and the switch must cross-router.
If satisfied these two requirements, can use telnet access to the switch, and then configure
the switch.
1）Establish configuration environment, just connect PC’s Ethernet port connect to the
switch’s Ethernet port through Local area network.
(Figure 1.2.1)
2）Run the Telnet program on the PC, need to input“Telnet+ Space+ switch’s IP address”
for checking, Figure 1.2.2 as follows:
(Figure 1.2.2)

CLI user manual
5
3）Hit “Enter”, checkout successful and till PC show “Please input hostname and password”,
ask user to input user name and password, default is admin, figure 1.2.3 as follows:
(Figure 1.2.3)
4）Use command to configure the switch and check the running statues, if need help,
please input“?” at any time. Specific configuration command, please reference“Managed
switch CLI user manual”.
1.3 Agreement
1. Command line format agreement table 1.3.1 as follow
Table 1.3.1
Format
Description
Bold
Key words of the command show by bold type.
italic
Parameter of the command show italic type.
[ ]
It shows part in “[]”is optical when command configuration is need.
{ x | y | ... }
It shows to pick up one from two or more items.
[ x | y | ... ]
It shows to pick up one or no one from two or more items.
2. Format agreement of figure interface Table 1.3.2 as follows:
Table 1.3.2
Format
Description
< >
“< >” shows press name, like ”click<OK>”
[ ]
“[ ]” shows windows name, menu name and data list. like “eject [create
user]window”
/
Multilevel is separated by “/”. Like [file/create/folder] means[create] a [folder] under
the menu of [file]

CLI user manual
6
1.4 Command line port
The switch provides command lines port and its configuration for user’s easy
configuration and management. Command lines port includes the following features:
1. Local configuration through Console port;
2. Supports history command saving which means it can save 10 pieces. History
commands can be selected by up and down key.
3. User can type in “help” or ”?” to get some help;
4. Supports intelligent complement with Tab when commands input;
5. Command interpreter take the method of partial matching. User can type in
conflict-free key words, such as config command, only need to type in conf.
1.4.1 View of Command Lines
The switch view of command lines aim at configuration of different functions. First of all,
the switch establish connection, then confirmation of user name and password finished, after
enter the correct user name and password, enter “help or ?” in “switch”, enter into system
view, Under the view of system, corresponding view appears after typing indifferent
command.
Table 1.4.1 system view command list
View
Function
DOS Prompt
Enter
Quit
System View
Switch#
Quit and
return to
user login
Information
Show or modify device
information, like software
version, IP address, etc.
Switch
(information)#
Information
Exit and
return to
the view
of system
Serial server
Show or modify the COM
setting and information
Serial(COM1)#
Serial
Port Settings
Show or modify the port
information, such as: duplex
mode, port enable
Switch (Port)#
Port
Bandwidth
Management
Show or modify the
bandwidth information, such
as the inlet and outlet
bandwidth settings etc.
Switch
(Bandwidth)#
Bandwidth
IGMP Snooping
Set IGMP snooping or IGMP
query, show MAClist
Switch
(Igmp)#
IGMP
VLAN
View or modify the Vlan
information, such as the
addition of Vlan, PVID, port
type etc.
Switch (Vlan)#
Vlan

CLI user manual
7
QoS
View or modify the Qos, Tos
value, such as Qos, Tos etc.
Switch (QoS)#
QoS
Rapid Ring
View or modify information
such as the net ring, ring ID,
ring port, RSTP information
etc. View or modify the RSTP
information
Switch (Ring)#
Ring
Port Trunking
View or modify the port trunk
information, such as the trunk
port
Switch (Trunk)#
Trunk
SNMP
Configuration
SNMP enable configuration
Switch(Snmp)#
Snmp
Relay Warning
View or modify the alarm
information, such as power
alarm, and port alarm.
Switch (Alarm)#
Alarm
Port Statistics
Port to receive the frame and
the total amount of data
statistics
Switch(Statistic
s)#
Statistics
Diagnosis
View or modify the mirror port
information
Switch (mirror)#
Mirror
Basic Settings
View or modify the settings
information, such as the IP
address, subnet mask,
default gateway, the user
password
Switch
(manage)#
Manage
Static Multicast
Filtering
Show or modify static
multicast address, like add
static multicast address.
Switch
(Multicast) #
Multicast
1.4.2 Command lines online help
Command lines port provides the following online help:
Total help;
Partial help;
1. Total help
Type in a command and “?”, between there is a space, if key word is in this location, then
type in all keywords and descriptions.
Example:
Switch(information)# ?
List --List commands of current menu
Help --Help commands of current menu

CLI user manual
8
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Show mac --Show device MAC Address
Show version --Show device version
Show others --Show device type,name,etc
Config --Config device type,name,etc
Clean --Clean device type,name,etc
2. Partial help
1）Type in a character string with <?>. It can show all commands beginning with this
character string.
Example:
Switch# M?
Mirror <dir> --Enter port mirror menu
Manage <dir> --Enter system manage menu
Multicast <dir> --Enter static multicast filters menu
2）Type in former letters of some key word of the command, press<Tab> key. If the letters
are unique, it can show the completed key word.
Example:
Switch# inf+<Tab>
Switch# information
1.4.3 Frequent Incorrect Information of Command Lines
All commands typed by users, if it is certificated by grammar, it can run correctly, or
users will be sent incorrect information. Frequent incorrect information is in table 1.4.3 as
below:
Table 1.4.3 Frequent incorrect information
English incorrect information
Reason
Invalid Command
Command cannot be found.
Key word cannot be found.
The type of parameter is wrong.
The parameter is beyond the border.
Incomplete Command
Command is not completed.
Too many parameters
Parameter is too much.
1.4.4 History command

CLI user manual
9
Command lines port can provides the function similar to Dos key. It automatic save command lines
that users types in, and users can use these history commands. Detailed operating please check table
1.4.4 as follows:
Table 1.4.4 access history command
Operating
Key
Result
Visit previous history
command
Up <↑>
If it exists earlier command, it is taken out.
Visit next history command
Down <↓>
If it exists later command, it is taken out.
1.4.5 General Command
Regular command is the most frequently used commands, in order to facilitate the operation,
the list and help, quit, exit and reboot command arrangements in all modes.
Table 1.4.5 general command
Operating
Key
Result
List commands of current menu
List
In any mode can be executed
Help commands of current
menu
Help
Quit from CLI
Quit
Exit from current menu
Exit
Reboot switch
Reboot

CLI user manual
10
CHAPTER 2 Device system based information configuration
Device information includes Device Type, Hardware Version, Device Name, Software Version, Device
Description, Device SN and Contact Way. Among them, Hardware Version and Software Version can be
only read, not modified.
2.1 Enter into the view of device information
Please check the view as figure 2.1.1 Table 2.1.1
Operating
Command
Description
Enter into the view of device information
Information
Run in the view of system
Switch# information
Switch(information)# ?
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Show mac --Show device MACAddress
Show version --Show device version
Show others --Show device type,name,etc
Config --Config device type,name,etc
Clean --Clean device type,name,et
2.2 Display device information
Please check the device information command as table 2.2.1
Table 2.2.1
Operating
Command
Description
Show system version
show version
Carry out under the view of device information
Show MAC address of device
show mac
Carry out under the view of device information
Show Device Type, Name, etc.
show others
Carry out under the view of device information
Configure device model, name
etc
config
Carry out under the view of device information
Delete device model, name etc
clean
Carry out under the view of device information
Example: Enter into device information view, enter the bold type command as follows and enter return
key
Switch# information

CLI user manual
11
Switch(information)# show others
Device type MangedSwitch
Device name IndustrialSwitch
Description 5PORT
Serial number
Contact way
2.3 Configuration information
Please reference user configuration device information as table 2.3.1:
Table 2.3.1
Operating
Command
Description
Configure Device Type
config –ttype
Type: configurable type, the length is
between 1～16 characters
Configure Device Name
config -n name
Name: configurable name, the length is
between1～16 characters
Configure Serial Number
config -m number
Number: configurable number, the length is
between 1～28 characters
Configure Device Description
config -p
description
Description: configurable description, the
length is between 1～16 characters
Configure Contact
information
config -c contact
Contact: Configure Contact way 1-28 bytes
Example: Configure device name as AB123, enter the bold type command as follows and enter return
key:
Switch(information)# config -n ABC123
[OK]
2.4 Delete device information
Please reference table 2.4.1 Table 2.4.1
Operating
Command
Description
Delete Device Type
Clean –t
Carry out under the view of device information
Delete Device Name
Clean -n
Carry out under the view of device information
Delete Serial Number
Clean -m
Carry out under the view of device information
Delete Device
Description
Clean -p
Carry out under the view of device information
Delete Contact
information
Clean -c
Carry out under the view of device information
Example: Delete device name, enter the bold type command as follows and enter return key:

CLI user manual
12
Switch(information)# clean -n
[OK]
Example: Delete Serial Number, enter the bold type command as follows and enter return key:
Switch(information)# clean -m
[OK]
Example: Delete Contact information, enter the bold type command as follows and enter return key:
Switch(information)# clean -c
[OK]

CLI user manual
13
Chapter 3 Serial Configuration
Serial server support 4 port serial, each serial port included 2 mode configuration: based
mode configuration and advanced mode configuration.
Based mode: Support 0~4 sessions(option), working mode: TCP Client, TCP Server, UDP
and TcpAuto.
Advanced mode: Support 0~4 sessions(option), working mode: TCP Server, UDP.
3.1 Enter into serial configuration view
Please reference table 3.1.1
Table 3.1.1
Operating
Command
Description
Enter into serial configuration view
Serial
Carry out under the view of
device information
Enter into serial information
configuration
Com <port>
<port>：
Option port number 1, 2, 3, 4
Example: Enter into serial configuration view, enter the bold type command as follows and enter return
key:
Serial(COM1)# ?
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Show config --Show COM config information
Show link --Show COM link state information
Show err --Show COM send err data
Clear err --Clear COM send err counter
Com1 --Enter serial com1 setting menu
Com2 --Enter serial com2 setting menu
Config --Config serial
Set Packs_bytes --COM set
Set Packs_time --COM set
Set Com_mode --COM set
Set OneToMulti --COM set
Set TCP_C --COM set
Set UDP --COM set
Set TCP_S --COM set
Set TCP_A --COM set
Set Session_multi --COM set
Set TCP_S_multi --COM set

CLI user manual
14
Set UDP_multi --COM set
3.2 Display serial information
Please check the table 3.2.1 Table 3.2.1
Operating
Command
Description
Display information of serial
connection statues
Show link
<port_list>
<port_list>: Choice the port number of serial
1、2、3、4 or all optional
Statistics incorrect
information of the serial
Show err
<port_list>
<port_list>: Choice the port number of serial
1、2、3、4 or all optional
Display serial configuration
information
Show
config<port_list
>
<port_list>: Choice the port number of serial
1、2、3、4 or all optional
Example: Display COM1 connection statue, enter the bold type command as follows and enter return
key:
Serial(COM1)# show link 1
COM<1>
Session<1>
Session mode: TCP server
Local port: 30000
Dest ip: 192.168.1.134
Local port: 4904
Session<2>
Session<3>
Session<4>
Example: Statistics COM1 incorrect information, enter the bold type command as follows and enter
return key:
Serial(COM1)# show err 1
COM<1>
COM err: 0 bytes
Session<1>
ch err: 0 bytes
Session<2>
ch err: 0 bytes
Session<3>
ch err: 0 bytes
Session<4>

CLI user manual
15
ch err: 0 bytes
Example: Display COM1 configuration information, enter the bold type command as follows and enter
return key:
Serial(COM1)# show config 1
COM<1>
Buadrate: 115200(bps)
Data bit: 8(bits)
Parity bit: NONE(bits)
Stop bit: 1(bits)
Packs bytes: 200(bytes)
Packs time space: 20(ms)
COM work mode: RS232
Session Option: OneToOne
Session<1>
State: Enable
Session mode: TCP server
local port: 30000
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<2>
State: Disable
Session mode: TCP server
local port: 30001
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<3>
State: Disable
Session mode: TCP server
local port: 30002
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<4>
State: Disable
Session mode: TCP server
local port: 30003