3One data IES7110-2GS Series User manual

- 1 -
IES7110-2GS Series
Managed Industrial Ethernet Switch
User manual
Shenzhen 3onedata Technolog Co., Ltd.
Tel: [phone] Fax: [phone]
www.3onedata.com
 Summarize 
IES7110-2GS erie i an indu trial grade, managed and
redundancy Ethernet witch. It included IES7110-2GS-P
(12/48VDC), IES7110-2GS-P (110/220VAC), IES7110-2GS-2F-P
(12/48VDC) and IES7110-2GS-4F-P (12/48VDC). IES7110-2GS
erie provided ome kind of advanced network managed
function, like a : SW-Ring redundancy ring network, VLAN,
Trunking, Quality of Service, Speed control, port mirroring, fault
alarm and firmware upgrade online. SW-Ring can bring your
Ethernet to intelligent redundancy. Standard Indu try de ign can
ati fied every requirement of the indu try cene. All component
u ed indu try grade, it take product high Reliability. It provided
wide voltage power upply input.
SW-RingTM i de igned a rapid redundancy network arithmetic.
It provided recover technology for fault of rapid redundant
network, the recovery time<20m .
 Packing list 
The indu trial Ethernet witch i hipped with the following item .
If any of the e item are mi ing or damaged, plea e contact your
cu tomer ervice repre entative for a i tance.
Indu trial Ethernet witch

1
Documentation and oftware CD

1
U er manual

1
DIN-Rail mounting kit

1
Warranty card

1
 Feature 
High performance network exchange technolog
Support IEEE802.3, IEEE802.3u, IEEE 802.3x,
IEEE802.3z, IEEE802.1Q, IEEE802.1p, IEEE802.1D/W
SW-Ring ring network patent technology (Fault recovery
time<20m

Support RSTP, way exchange time<50m
Support WEB configuration
Support MAC addre learning, aging automatic
Support port tatu di play, data update.
Support tatic and dynamic IGMP
Support flow tati tic
Support bi-directional port mirroring
Support rate control, Broadca t torm control
Support configuration file up and download
Support 1 channel relay alarm output
Reliable Industrial grade design
Indu trial grade 4 de ign, -40-75

work temperature
No fan deign
IP40 protection grade
 Panel la out 
Vertical view and bottom view Rear view
Front panel view

- 2 -
1. DIP witche for default factory
2. Con ole port
3. 2-pin terminal block for relay output
4. Ground crew
5. Power input terminal block
6. Screw hole for Wall Mounting Kit
7. DIN-Rail mounting kit
8. Power indicator
9. Sy tem running LED
10. Relay alarm LED
11. Link/ACT LED
12. Gigabit SFP port
13. 10Ba e-T /100Ba e-TX Ethernet port
14. 100Ba e-FX fiber port
 Power suppl input 
DC Series Switch:
The product top panel provided 4 bit power upply input terminal
block, upport DC input. DC power upply input upported
redundancy function, provided PWR1 and PWR2 power input,
can u e for ingle, and can connect 2 eparately power upply
y tem, u e 1 pair terminal block connect the device at the ame
time. If one of the power y tem broke, the device can work
un-interruptible. Built-in overcorrect protection, Rever e
connection protection. Voltage input range i 12

48VDC

terminal block defined a : V1-

V1+

V2-

V2+

.
AC Series Switch:
The Indu trial Ethernet witche have inge power and
redundancy power two kind of power input. The inge power AC
erie top panel provide 3 bit terminal block for
100~240VAC/DC power entered (L/+, FG, N/-)
Important notice:
1. Power ON operation: fir t of all, in ert power cable’ terminal
block into device’ power port, then in ert power upply plug into
power ource
2. Power OFF operation: Fir t off all, unpin power plug, then
trike the terminal block, plea e take care of operation equence.
 Dimension 
The erie of product are the ame ize, and the number of the
Ethernet interface i different. Unit (mm)
 DIP Switch 
Top panel provided 4 bit DIP witch to do function configure

ON to enable effective

,1 and 4 keep for future function. 2 i
recovery default factory. 3 i for upgrade. Plea e power off and
power on when you change the tatu of DIP witch.
 Rela connection 
Relay acce terminal in the top panel of the device. Between the
two terminal relay, a an open circuit tate in normal non alarm
tate, when there i any alarm information to the clo ed tate. The
two terminal block connector are u ed to detect both power failure
and port failure. The two wire attached to the Fault contact form
an open circuit when the device ha lo t power upply from one of
the DC power input or one of the port i failure. (Note: The AC
power witch doe not upport power alarm.)
 Console port 
Thi erie product provided 1pc procedure te t port ba ed in
erial port. It adopt RJ45 interface, located in top panel, can
configure related command through RJ45 to DB9 female cable.
 Communication connector 
10/100BaseT(X) Ethernet port
The pinout define of RJ45 port di play a below, connect by UTP
or STP. The connect di tance i no more than 100m. 100Mbp i

- 3 -
u ed 120

of UTP 5, 10Mbp i u ed 120

of UTP 3 ,4, 5.
RJ45 port upport automatic MDI/MDI-X operation. can connect
the PC, Server, Converter and HUB .Pin 1,2,3,6 Corre ponding
connection in MDI. 1→3, 2→6, 3→1, 6→2 are u ed a cro
wiring in the MDI-X port of Converter and HUB.
10Ba e-T/100Ba e-TX are u ed in MDI/MDI-X, the define of Pin
in the table a below.
NO. MDI ignal MDI-X ignal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
6 RX- TX-
4, 5, 7, 8
 
Note
 
TX
 
Tran mit Data
  
RX
 
Receive Data
    
Not u e.
10/100Base-T(X) MDI (straight-through cable)
10/100Base-T(X) MDI-X (Cross over cable)
MDI/MDI-X auto connection make witch ea y to u e for
cu tomer without con idering the type of network cable.
100Base-FX Fiber port
100Ba e-FX full-duplex SM or MM port, SC/ST/FC type .The
fiber port mu t be u ed in pair, TX (tran mit) port connect remote
witch’ RX(receive) port; RX(receive) port connect remote
witch’ TX(tran mit) port.
The optical fiber connection upport the line to in truct enhance
the reliability of network effectively.
Suppose: If you make your own cable, we ugge t labeling the
two ide of the ame line with the ame letter (A-to-A and B-to-B,
hown a below, or A1-to-A2 and B1-to-B2).
1000Base SFP fiber port(mini-GBIC)
1000Ba e- SFP fiber port adopt gigabit mini-GBIC tran mi ion,
can choice different SFP module according to different tran fer
di tance. Fiber interface mu t u e for pair, TX port i tran mit ide,
mu t connect to RX (receive ide). The fiber interface upport lo
line indicator.
Suppose: If you make your own cable, we ugge t labeling the
two ide of the ame line with the ame letter (A-to-A and
B-to-B, hown a below, or A1-to-A2 and B1-to-B2).
 LED Indicator 
LED indictor light on the front panel of product, the function of
each LED i de cribed in the table a below.
S stem indication LED
LED State Description
P1
ON Power i being upplied to power
input PWR1
OFF Power i not being upplied to
power input PWR1
P2
ON Power i being upplied to power
input PWR2
OFF Power i not being upplied to
power input PWR2
Alarm
ON When the alarm i enabled, power
or the port’ link i inactive.
OFF Power and the port’ link i
active, the alarm i di abled.
Run
ON/OFF Sy tem i not running well
Blinking Sy tem i running well
Link/ACT
(1~8/G1~G2)
ON Port connection i active
Blinking Data tran mitted
OFF Port connection i not active
 Installation 
Before in tallation, confirm that the work environment meet the
in tallation require, including the power need and abundant
pace. Whether it i clo e to the connection equipment and other
equipment are prepared or not.
1. Avoid in the un hine, keep away from the heat fountainhead or
the area where in inten e EMI.
2. Examine the cable and plug that in tallation requirement .
3. Examine whether the cable be eemly or not (le than 100m)
according to rea onable cheme.
1 8

- 4 -
4. Power: DC dual power upply erie product 12 ~ 48VDC
AC ingle power upply erie product 100~240VAC/DC
5. Environment: working temperature: -40

75

Storage Temperature: -40

85

Relative humidity 5%

95%
DIN Rail Installation
In order to u e in indu trial environment expediently, the product
adopt 35mm DIN-Rail in tallation, the in tallation tep a below:
1. Examine the DIN-Rail attachment
2. Examine DIN Rail whether be firm and the po ition i
uitability or not.
3. In ert the top of the DIN-Rail into the lot ju t below the
tiff metal pring.
4. The DIN-Rail attachment unit will nap into place a hown
below.
Wiring Requirements
Cable laying need to meet the following requirement ,
1. It i needed to check whether the type, quantity and
pecification of cable match the requirement before cable
laying;
2. It i needed to check the cable i damaged or not, factory
record and quality a urance booklet before cable laying;
3. The required cable pecification, quantity, direction and
laying po ition need to match con truction requirement , and
cable length depend on actual po ition;
4. All the cable cannot have break-down and terminal in the
middle;
5. Cable hould be traight in the hallway and turning;
6. Cable hould be traight in the groove, and cannot beyond the
groove in ca e of holding back the inlet and outlet hole .
Cable hould be banded and fixed when they are out of the
groove;
7. U er cable hould be eparated from the power line . Cable ,
power line and grounding line cannot be overlapped and
mixed when they are in the ame groove road. When cable i
too long, it cannot hold down other cable, but tructure in the
middle of alignment rack;
8. Pigtail cannot be tied and werved a le a po ible.
Swerving radiu cannot be too mall ( mall werving cau e
terrible lo of link). It banding hould be moderate, not too
tight, and hould be eparated from other cable ;
9. It hould have corre ponding imple ignal at both ide of the
cable for maintaining.
 Specification 
Technolog
Standard: Support IEEE802.3, IEEE802.3u, IEEE802.3x,
IEEE802.3z, IEEE802.1Q, IEEE802.1p, IEEE802.1D/W
Protocol: ARP, ICMP, TCP, UDP, DHCP, DNS, HTTP, Telnet,
SW-Ring, RSTP, SNMP
Flow control: IEEE802.3x flow control, back pre flow control
Interface
Electric port: 10Ba e-T/100Ba e-TX/1000Ba e-TX auto peed
control, Half/full duplex and MDI/MDI-X auto detect
100M optic fiber port: 100Ba e-FX, SC/ST/FC connector
Gigabit SFP port: 1000Ba e-FX, SFP lot
Con ole port: debug erial port carry out CLI command
Alarm port: 2 bit 7.62mm terminal block,
1 channel relay alarm output
Exchange attribute
100M forward peed: 148810pp
1000M forward peed: 1488100pp
Tran mit mode: tore and forward
Sy tem exchange bandwidth: 7.6G
MAC addre table: 8K
Memory: 1M
Transfer distance
Twi ted cable: 100M

tandard CAT5/CAT5e cable

Multi-mode: 1310nm, 2Km
Single-mode: 1310nm, 20/40/60Km
1550nm, 80/100/120Km
Power suppl
 DC input erie
Input voltage: 12~48VDC
 AC input erie
Input voltage: 100~240VAC/DC
Type of input: 4 bit 7.62mm pitch terminal block
Overload current protect: 4.0A (DC) or 5.0A (AC)
Support DC dual power upply redundancy and alarm input
Support DC input no parity, protection rever e connection
Consumption
IES7110-2GS-P (12/48VDC):
Unload con umption: 2.2W@24VDC
Full load con umption: 5.5W@24VDC
IES7110-2GS-P (220VAC):
Unload con umption: 2.7W@220VAC
Full load con umption: 5.5W@220VAC
IES7110-2GS-2F–P (12/48VDC):
Unload con umption: 5.1W@24VDC
Full load con umption: 8.0W@24VDC
IES7110-2GS-4F–P (12/48VDC):
Unload con umption: 6.1W@24VDC

- 5 -
Full load con umption: 9.0W@24VDC
Working environment
Working temperature: -40

75

Storage temperature: -40

85

Relative Humidity: 5%~95% (no conden ation)
Mechanical Structure
Shell: IP40 protect grade, metal hell
In tallation: DIN-Rail mounting
Weight: 720g
Size

W×H×D

: 110mm×138mm×53mm
Industr Standard
EMI: FCC Part 15, CISPR (EN55022) cla A
EMS: EN61000-4-2 (ESD), Level 4
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 4
EN61000-4-5 (Surge), Level 4
EN61000-4-6 (CS), Level 3
EN61000-4-8, Level 5
Shock: IEC 60068-2-27
Free fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Certification
CE, FCC, RoHS, UL508 (Pending)
Warrant : 5 year