3One data TNS5800-8GP16GT-P24VDC User manual

TNS5800-8GP16GT-P24VDC
Rack-mounted
Industrial Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Te l : [phone]
Fax: [phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the switch.
1.
Industrial Ethernet switch
2.
Warranty card
3.
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
This product is Layer 3 rack-mounted industrial Ethernet
switch designed for rail transit. Model:
TNS5800-8GP16GT-P24VDC (8 Gigabit PoE copper ports +
16 Gigabit copper ports + 1 24VDC (12~36VDC) power
supply).
【
Panel Design
】
Front View
Top view
Left view
Right view
1. Lugs
2. Grounding screw
3. Relay output terminal blocks
4. Terminal block for power input
5. Power supply indicator (PWR)
6. Running indicator (RUN)
7. Alarm indicator (ALM)
8. Console port
9. Gigabit POE copper port (M12)
10. Interface connection indicator
11. PoE indicator
12. Gigabit copper port (M12)
【
Mounting Dimension
】
Unit: mm
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.

The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Rack-mounted】
Step 1 Select the device mounting location to ensure
enough size.
Step 2 Put the device on the plane plate of the rack, and
install the left and right lugs on the rack with 4
screws.
Step 3 Check and confirm the product is mounted firmly on
the rack, mounting ends.
【Disassembling Device】
Step 1 Power off the device.
Step 2 Unscrew the fixed mounting lug screw on the rack.
Step 3 Shift out the device from rack, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【
Power Supply Connection
】
The device provides 3-pin 5.08mm pitch
DC power terminal block, power supply
range: 24VDC (12-36VDC).
【
Relay Connection
】
This device provides 3-pin 5.08mm pitch
relay terminal blocks, which are a set of
normally open contacts of the device alarm relay. They are
open circuit in the state of normal non alarm, closed when any
alarm information occurs. For example, they are closed when
powered off, and send out alarm. The series of switch support
1 relay alarm information output that can output DC power
supply alarm information or network abnormality alarm. It can
be connected to alarm light or alarm buzzer or other switching
value collecting devices, which can timely inform operators
when the alarm occurs.
【Communication Interface Connection】
This device provides 24 10/100/1000Base-T(X)
interfaces, the interface type is M12 X-Coded
8-Pin slot (female), therein G1-G8 supports
PoE function, support IEEE802.3at/af
self-adaption. The pin definitions of M12 are shown as follows:
Pin No. Pin Definition Description
1 BI_(DA+) Positive bi-directional data
of Gigabit Ethernet group 1
2 BI_(DA-) Negative bi-directional data
of Gigabit Ethernet group 1
3 BI_(DB+) Positive bi-directional data
of Gigabit Ethernet group 2
4 BI_(DB-) Negative bi-directional data
of Gigabit Ethernet group 2
5 BI_(DD+) Positive bi-directional data
of Gigabit Ethernet group 4
6 BI_(DD-) Negative bi-directional data
of Gigabit Ethernet group 4
7 BI_(DC-) Negative bi-directional data
of Gigabit Ethernet group 3
8 BI_(DC+) Positive bi-directional data
of Gigabit Ethernet group 3
【
Console Port Connection
】
The device provides 1 program debugging port based on
RS232 serial port which can conduct device CLI command
management after connecting to PC. The interface adopts
RJ45 port, the RJ45 pin definition as follows:
Pin No.
2
3
5
Pin Definition
TXD
RXD
GND
【
Checking LED Indicator
】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate
Description
PWR
ON
Power is connected and running
normally
OFF
Power supply is disconnected or
running abnormally
ALM
ON
Port link has alarm
OFF
Port link has no alarm
RUN
ON The device self-
check hasn't
finished or the device is abnormal.
OFF The device is powered off or the
device is abnormal.
Blinking Blinking about 1 time per second,
system is running normally
Link/Act
ON
Ethernet port has established a
valid network connection
Blinking Ethernet
port is in an active
network status
OFF Ethernet port has not established
valid network connection
PoE ON
POE port is powering other
devices normally
OFF
POE is disabled or disconnected
【
Logging in to WEB Interface
】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Step 1 Configure the IP addresses of computer and the

device to the same network segment, and the
network between them can be mutually accessed
Step 2 Enter device’s IP address in the address bar of the
computer browser.
Step 3 Enter device’s username and password in the login
window as shown below.
Step 4 Click “OK” button to login to the WEB interface of
the device.
Note:
The default IP address of the device is “192.168.1.254”.
The default username and password of the device are
“admin123”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【
Specification
】
Panel
Gigabit M12
10/100/1000Base-
T(X), M12(Female),
8-Pin X-
Coded, Automatic Flow
Control, Full/half Duplex Mode,
MDI/MDI-
X Autotunning; Therein
G1-G8 supports PoE function,
supports IEEE802.3at/af self-adaption;
the maximum capacity of a single port
is 30W PoE power supply output;
When the device inputs 24VDC, the
maximum capacity of total PoE power
is up to 100W
Console port
CLI command management port, RJ45
Alarm interface
3-
pin 5.08mm pitch terminal blocks,
support 1 relay alarm output, current
load capability is 5A@30VDC or
10A@125VAC
Indicator
Power supply indicator, run indicator,
interface indicator, alarm indicator, PoE
indicator
Switch Property
Backplane
bandwidth
128G
Packet buffer
size
12Mbit
MAC Address
Table
16K
Power Supply
Value range
24VDC
（
12~36VDC
）
Power terminal
block
3-pin 5.08mm pitch terminal block
Power Consumption
No-load
20.5W@24VDC
Full-load
22.6W@24VDC
Working Environment
Working
temperature
-40~75℃(65℃with PoE load)
Storage
temperature
-40~75℃
Working
humidity
5%～95% (no condensation)
Protection
grade
IP40 (metal shell)