ACME LED?7TC User manual

LED‐7TC
UserGuide
Pleasereadtheinstructioncarefullybeforeuse

1B
Contents
1.SafetyInstructions....................................................................................................2
2.TechnicalSpecifications ............................................................................................3
3.Installation................................................................................................................4
4.HowtoSettheFixture..............................................................................................4
4.1ControlPanel ......................................................................................................4
4.2MainFunction .....................................................................................................5
5.HowtoControltheUnit .........................................................................................10
A.UniversalDMXcontroller ...................................................................................10
B.Master/Slaveoperation......................................................................................11
C.EasyController(byCA‐8)....................................................................................11
6.DMX512Configuration ..........................................................................................12
7.DMX512Connection..............................................................................................13
8.Troubleshooting......................................................................................................14
9.CleaningAndMaintenance ....................................................................................15


2B
1.SafetyInstructions
WARNING
yPleasekeepthisUserManualforfutureconsultation.Ifyousellthefixturetoanotheruser,be
surethattheyalsoreceivethisinstructionbooklet.
yUnpackandcheckcarefullythereisnotransportationdamagebeforeusingthefixture.
yBeforeoperating,ensurethatthevoltageandfrequencyofpowersupplymatchthepower
requirementsofthefixture.
yIt’simportanttogroundtheyellow/greenconductortoearthinordertoavoidelectricshock.
yDisconnectmainpowerbeforeservicingandmaintenance.
yUsesafetychainwhenfixesthisfixture.Don’thandlethefixturebytakingitsheadonly,but
alwaysbytakingitsbase.
yMaximumambienttemperatureisTa:40℃.Don’toperateitwherethetemperatureishigher
thanthis.
yIntheeventofseriousoperatingproblem,stopusingthefixtureimmediately.Nevertryto
repairthefixturebyyourself.Repairscarriedoutbyunskilledpeoplecanleadtodamageor
malfunction.Pleasecontactthenearestauthorizedtechnicalassistancecenter.Alwaysusethe
sametypespareparts.
yDonotconnectthedevicetoanydimmerpack.
yDonottouchanywireduringoperationandtheremightbeahazardofelectricshock.
yTopreventorreducetheriskofelectricalshockorfire,donotexposethefixturetorainor
moisture.
yThehousingmustbereplacediftheyarevisiblydamaged.
yDonotlookdirectlyattheLEDlightbeamwhilethefixtureison.
Warning:



Pleasereadtheinstructionscarefullywhichincludesimportant
informationabouttheinstallation,operationandmaintenance.
Ifusinga230Vac50Hzpowersupply,donotconnectinseriesmorethan20units,use
anothermainssupplyforthenext20units.
Ifusinga120Vac60Hzpowersupply,donotconnectinseriesmorethan10units,use
anothermainssupplyfornext10units.

3B
yTopreventorreducetheriskofelectricalshockorfire,donotexposetheunittorainor
moisture.
yDonotopentheunitwithinfiveminutesafterswitchingoff.
yThehousing,thelenses,ortheultravioletfiltermustbereplacediftheyarevisiblydamaged.
Caution:
Therearenouserserviceablepartsinsidethefixture.Donotopenthehousingorattemptany
repairsyourself.Intheunlikelysituation,yourunitmayrequireservice,pleasecontactyour
nearestdealer.

2.TechnicalSpecifications
•DMXchannel:4channelmodes
•LED:7x3WRGB(Tri‐color)LED
•Powersupply
InputVoltage:AC100V‐240V~50/60Hz
•Powerconsumption:28.5W
•Fuse:T6.3A
•Dimension:212x80x212mm
•Weight:2.5kgs

4B
3.Installation
Theunitshouldbemountedviaitsscrewholesonthebracket.Alwaysensurethattheunitis
firmlyfixedtoavoidvibrationandslippingwhileoperating.Alwaysensurethatthestructureto
whichyouareattachingtheunitissecureandisabletosupportaweightof10timesoftheunit’s
weight.Alsoalwaysuseasafetycablethatcanhold12timesoftheweightoftheunitwhen
installingthefixture.
Theequipmentmustbefixedbyprofessionals.Anditmustbefixedataplacewhereisoutofthe
touchofpeopleandhasnoonepassbyorunderit.
4.HowtoSettheFixture
4.1ControlPanel
○
1Display:Toshowthevariousmenusandtheselectedfunctions
LED:
○ 2DMXOnDMXinputpresent
○ 3MASTEROnMasterMode
○ 4SLAVEOnSlaveMode
○ 5SOUNDFlashingSoundactivation
Button:
○
6MENUToselecttheprogrammingfunctions

5B
○
7DOWNTogobackwardintheselectedfunctions
○
8UPTogoforwardintheselectedfunctions
○
9ENTERToconfirmtheselectedfunctions
○
10 Microphone:Receivemusicforthesoundactive.
○
11 Onlyforremotecontrol:ByconnecttotheCA‐8tocontroltheunitforStandby,Function
andModefunction.
○
12 DMXoutput:ForDMX512link,use3/5 ‐pinXLRplugcabletolinkthenextunit.
○
13 DMXinput:ForDMX512link,use3/5 ‐pinXLRplugcabletoinputDMXsignal.
○
14 Mainsinput:Connecttosupplymainspower.
○
15 Mainsoutput:Connecttosupplymainspowerforthenextunit.
4.2MainFunction
Toselectanyofthegivenfunctions,presstheMENUbuttontoshowtherequiredoptiononthe
display.SelectthefunctionwiththeENTERbuttonandthedisplaywillblink.UsetheDOWNand
UPbuttonstochangethemode.Oncetherequiredmodehasbeenselected,PresstheENTER
buttontostore.TogobacktothemainmenuwithoutanychangespresstheMENUbutton.Hold
andpresstheMENUbuttonaboutonesecondorwaitforoneminutetoexitthemenumode.The
mainfunctionsareshownbelow:




6B

7B
DMX512AddressSetting
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressENTERbuttonand
thedisplaywillblink.UseDOWNandUPbuttontochangetheDMX512Address(1‐512)orselect
(autosettingDMX512address).Onceselected,presstheENTERbuttontostoreor
automaticallyreturntothemainfunctionswithoutanychangesafter8seconds.Togobacktothe
functionswithoutanychangepresstheMENUbuttonagain.

Channelmode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingtheENTER
buttonandthedisplaywillblink.UsetheDOWNandUPbuttontoselectthe  (channel1)
or  (channel2)or(channel3)or  (channel4)mode.Oncethemodehasbeen
selected,presstheENTERbuttontosetuporautomaticallyreturntothemainfunctionswithout
anychangeafter8seconds.TogobacktothefunctionswithoutanychangepresstheMENU
buttonagain.

ShowMode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (autoshow)or 
(show1)or  (show2)or…(show12).Oncetheshowhasbeenselected,pressthe
ENTERbuttontoconfirm,ifyouselect(show1)or  (show2)or…(show
12),youcanpressDOWNandUPbuttontoselect(slowest)or…  (fastest),press
ENTERbuttontostoreorautomaticallyreturntothemainfunctionswithoutanychangeafter8
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.

ChaseMode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (chase1)or…or
(chase16)or  (fade).Oncethechasehasbeenselected,presstheENTERbuttontoconfirm,

8B
thenpressDOWNandUPbuttontoselect  (slowest)or…  (fastest),pressENTER
buttontostoreorautomaticallyreturntothemainfunctionswithoutanychangeafter8seconds.
TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.

SlaveMode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe(Mater)or 
(normal)or…or  (16lightshow)mode.Oncethemodehasbeenselected,presstheENTER
buttontosetuporautomaticallyreturntothemainfunctionswithoutanychangeafter8seconds.
TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.

Soundcontrol
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (soundcontrolon)or
(soundcontroloff).Oncethemodehasbeenselected,presstheENTERbuttontosetupor
automaticallyreturntothemainfunctionswithoutanychangeafter8seconds.Togobacktothe
functionswithoutanychangepresstheMENUbuttonagain.

BlackoutMode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe (noblackout)or 
(yesblackout)mode.Oncethemodehasbeenselected,presstheENTERbuttontosetupor
automaticallyreturntothemainfunctionswithoutanychangeafter8seconds.Togobacktothe
functionswithoutanychangepresstheMENUbuttonagain.

ColorMode
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (color1)or…or 

9B
(show16)or  (manualsetting).Onceselect,presstheENTERbuttontoconfirm,ifyou
select  (manualsetting),youcanpressDOWNandUPbuttontoselect  (red)or
(green)or  (blue),pressENTERbuttontoconfirm,thenuseDOWNandUPbutton
toadjustthevalue(0‐255)andpressENTERbuttontostore,automaticallyreturntothemain
functionswithoutanychangeafter8seconds.Togobacktothefunctionswithoutanychange
presstheMENUbuttonagain.

LEDDisplay
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (LEDon)or  (LED
off)mode.Oncethemodehasbeenselected,presstheENTERbuttontosetuporautomatically
returntothemainfunctionswithoutanychangeafter8seconds.Togobacktothefunctions
withoutanychangepresstheMENUbuttonagain.

DisplayInversion
Itisgoodforyoutoinstalltheunitonthefloororunderceiling.PresstheMENUbuttonupto
whenthe  isshownonthedisplay.PressingENTERbuttonandthedisplaywillblink.Use
DOWNandUPbuttontoselectthe  (displayinversion)or  (displaynormal).Once
select,presstheENTERbuttontosetuporautomaticallyreturntothemainfunctionswithoutany
changeafter8seconds.TogobacktothefunctionswithoutanychangepresstheMENUbutton
again.

FixtureTemperature
PresstheMENUbuttonuptowhenthe  isblinkingonthedisplay.PressingENTERbutton
andthedisplaywillshowthetemperatureoftheunit.TogobacktothefunctionspresstheMENU
buttonagain.



10B
Whitebalance
PresstheMENUbuttonuptowhenthe  isshownonthedisplay.PressingENTERbutton
andthedisplaywillblink.UseDOWNandUPbuttontoselectthe  (red)or  (green)
or  (blue),pressENTERbuttontoconfirm,thenuseDOWNandUPbuttontoadjustthe
value(125‐255)andpressENTERbuttontostore,automaticallyreturntothemainfunctions
withoutanychangeafter8seconds.Togobacktothefunctionswithoutanychangepressthe
MENUbuttonagain.

FixtureHours
PresstheMENUbuttonuptowhenthe  isblinkingonthedisplay.PressingENTERbutton
andthedisplaywillshowthenumberofworkinghoursoftheunit.Togobacktothefunctionspress
theMENUbuttonagain.

Softwareversion
PresstheMENUbuttonuptowhenthe  isblinkingonthedisplay.PressingENTERbutton
andthedisplaywillshowtheversionofsoftwareoftheunit.Togobacktothefunctionspressthe
MENUbuttonagain.

5.HowtoControltheUnit
Therearethreewaystocontrolthefixture
A.UniversalDMXcontroller
B.Master/Slaveoperation
C.Easycontroller(byCA‐8)
A.UniversalDMXcontroller
ThefixturecanbesettheDMXaddressremotelybyuniversalDMXcontroller.First,youneedto
programmingtwoscenesintoachase,andthenlinkthefixturestotheuniversalDMXcontroller.
Whenyourunthechase,allthefixturesofthechainwillbesettheseriesDMXaddress
automatically.Thefixtureusesfourchannels.Pleaserefertothefollowingdiagramtosetthe

11B
addressforthefirstfourunits.


B.Master/Slaveoperation
Thefixturewillallowyoutolink16fixturestogetherandoperatewithoutacontroller.In
Master/Slavemode,thefirstfixturewillcontroltheotherstogiveanautomatic,soundactivated,
synchronizedlightshow.Thisfunctionisgoodwhenyouwantaninstantshow.Thefirstfixtureit’s
DMXinputcablewillhavenothingconnectit,andtheotherfixtureswillbesetinslavemode
automatically.TheirDMXinputcablesconnectthelastfixtureDMXoutputcable(daisychain).Any
fixturecanactasaMasterorasaSlave.
C.EasyController(byCA‐8)
Theeasyremotecontrolisusedonlyinmaster/slavemode.Thereisaterminatorfor
connecttheeasycontrollerinsidethefixture.ByconnectingthecableintoDMXIN
waterproofcableentryglandtotheCA‐8terminatorofthefirstfixture,youwillfind
thattheremotecontrolonthefirstfixturewillcontrolalltheotherfixturesforStand
by,FunctionandModefunctions.
BlackoutToblackoutallthefixture
FunctionStrobe
1.Synchronousstrobe
inwhitecolor
2.Thesamecolorchase
3.Differentcolorstrobe
SelectColor

Color1‐16or
manualsetting
color
Selectshow

Show1‐12
SelectChase

Chase1‐16orfade
ModeSound1
(LEDOFF)
Manual
(LEDON)
Sound2
(LEDslowblinking)
Auto
(LEDfastblinking)


12B
6.DMX512Configuration
4ChannelsMode:

13B
7.DMX512Connection
TheDMX512iswidelyusedinintelligentlightingcontrol,withamaximumof512channels.


1. Connectthefixturetogetherina“daisychain”withtheXLRplugcablefromtheoutputofthe
fixturetotheinputofthenextfixture.Thecablecannotbebranchedorsplittoa“Y”cable.
Inadequateordamagedcables,badsolderjointsorcorrodedconnectorscaneasilydistortthe
signalandshutdownthesystem
2. TheDMXoutputandinputconnectorspass‐throughtomaintaintheDMXcircuitwhenoneof
theunits’powerisdisconnected.
3. Atlastfixture,theDMXcablehastobeterminatedwithaterminatortoreducesignalerrors.
Soldera120‐ohm1/4 W resistorbetweenpin2(DMX‐)andpin3(DMX+)intoa3‐pinXLR‐plug
andplugitintheDMX‐outputofthelastfixture.
4. Eachlightingfixtureneedstohaveanaddresssettoreceivethedatasentbythecontroller.
Theaddressnumberisbetween0‐511(usually0&1areequalto1).
5. 3pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+)
5pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+),
Pin4/5:notused.

14B
8.Troubleshooting
Followingareafewcommonproblemsthatmayoccurduringoperation.Herearesome
suggestionsforeasytroubleshooting:
A. Thefixturedoesnotwork,nolight
1. Checktheconnectionofpowerandmainfuse.
2. Measurethemainsvoltageonthemainconnector.
B. NotrespondingtoDMXcontroller
1. DMXLEDshouldbeon.Ifnot,checkDMXconnectors,cablestoseeiflinkproperly.
2. IftheDMXLEDisonandnoresponsetothechannel,checktheaddresssettingsand
DMXpolarity.
3. IfyouhaveintermittentDMXsignalproblems,checkthepinsonconnectorsoronPCBofthe
fixtureorthepreviousone.
4. TrytouseanotherDMXcontroller.
5. CheckiftheDMXcablesrunnearorrunalongsidetohighvoltagecablesthatmaycause
damageorinterferencetoDMXinterfacecircuit.
C. Somefixturesdon’trespondtotheeasycontroller
1. YoumayhaveabreakintheDMXcabling.ChecktheLEDfortheresponseofthemaster/slave
modesignal.
2. WrongDMXaddressinthefixture.Settheproperaddress.
D. Noresponsetothesound
1. MakesurethefixturedoesnotreceiveDMXsignal.
2. Checkmicrophonetoseeifitisgoodbytappingthemicrophone.
E. Oneofthechannelsisnotworkingwell
1. ThesteppermotormightbedamagedorthecableconnectedtothePCBisbroken.
2. Themotor’sdriveIConthePCBmightbeoutofcondition.


15B
9.CleaningAndMaintenance
Thecleaningofinternalmustbecarriedoutperiodicallytooptimizelightoutput.Cleaning
frequencydependsontheenvironmentinwhichthefixtureoperates:damp,smokyorparticularly
dirtysurroundingcancausegreateraccumulationofdirtonthefixture’soptics.
yCleanwithsoftclothusingnormalglasscleaningfluid.
yAlwaysdrythepartscarefully.
yCleantheexternalopticsatleastevery20days.Cleantheinternalopticsatleastevery30/60
days.

Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
provision of the Electromagnetic Compatibility (EMC) Directive
2004/108/EC.
EN55103-1: 2009 ; EN55103-2: 2009;
EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.
&
Harmonized Standard
EN 60598-1:2008 + All:2009; EN 60598-2-17:1989 + A2:1991;
EN 62471:2008; EN 62493: 2010
Safety of household and similar electrical appliances
Part 1: General requirements

Innovation,Quality,Performance