ACME V-BOX User manual

CONTENTS
1. Technical Specifications ......................................................................... 2
2. Control Panel ......................................................................................... 3
3. Connections ........................................................................................... 4
4. Test Instructions..................................................................................... 5
4.1 ACME luminaire pressure test.......................................................... 5
4.2 User-defined pressure test ............................................................... 7
4.3 Air leakage test................................................................................. 9
5. System Setting ..................................................................................... 10
6. System Upgrade ................................................................................... 12
1C

1. Technical Specifications
Power Voltage:
AC 100~240V, 50/60Hz
Power Consumption:
Positive pressure: 40W
Negative pressure: 30W
Lux:
15L/minute
Maximum positive pressure:
80kpa
Maximum negative pressure:
-60kpa
Construction:
Display: LCD display
Accessories: An air pump; Four air pressure valves; Power Cable
Protection Rating: IP65
Control:
Firmware Upgrade: Update via USB link
Features:
V-BOX is a portable air tightness tester. The test objects are waterproof luminaires.
It is a non-destructive testing instrument based on the principle of pressure drop method and
using compressed air (or vacuum) as the medium to test products，The utility model has the
advantages of simple structure, complete functions and sensitive precision, which can be used
only by connecting the power interface and the luminaire interface, and can be used as an
emergency test equipment to test whether the luminaire is waterproof or leaky.
Dimension/Weight:
285x355x165mm, 7kgs
14”x6.5”x12.6”in, 15.4lbs
2C

2. Control Panel
4 Pressure/Vacuum.To Fixture
5.USB
6 STOP.
1 Display.2 Button.
7 POWER IN.
8 POWER SWITCH.
9 START.
3 User Manual.
1. Display:To show the various menus and the selected function
2. Button:
MENU
To enter into move backward or leave the menu
UP
To go backward to move up in the menu
DOWN
To go forward to move down in the menu
ENTER
To perform the desired functions
3. User Manual
4. Pressure/Vacuum To Fixture:
Used to connect the air hose to pump/transfer gas for the luminaire
5. USB:
Used to upgrade the system or export the test record
6. Stop:
Press to stop testing
7. Power In:
Used to connect to supply power
8. Power Switch:
Turn on/off the power
9. Start:
Press to start testing
3C

3. Connections
1. Connect the power cable to the fixture (Figure 1) and plug it in.
Figure 1
2. Take out the air hose (Figure 2), which has a quick-connect fitting and a bigger nozzle at each end
(Figure 3). Connect the air hose quick-connect fitting to the fixture (Figure 4). Carefully insert the
threaded end of the nozzle into the air relief valve hole of the luminaire and twist it until it is finger
tight (Figure 5), then switch the fixture on (Figure 6).
Figure 2
Figure 3
4C

Figure 4 Figure 5
Figure 6
3. To switch the fixture off, press the power switch again or remove the power cable directly.
4. Test Instructions
Attention: The connection between the luminaire and the V-BOX should be kept sealed, otherwise the
test will be affected.
4.1 ACME luminaire pressure test
1. Enter the Main Menu and use the UP/DOWN button to select Air Pressure Test (Figure 1), press the
ENTER button to confirm, press the MENU button to exit.
Figure 1
5C

2. Enter the Test Menu and use the UP/DOWN button to select Fixture Model(Figure 2), press the
ENTER button to confirm, press the MENU button to exit.
Figure 2
3. Use the UP/DOWN button to select the corresponding model on Select Model page (Figure 3), press
the ENTER button to restore, press the MENU button to exit.
Figure 3
4. Enter into the test page (Figure 4, Figure 5) and press the green button to start testing.
Figure 4 Figure 5
6C

5. If there is any problem during the test, please press the red button to stop the test.
6. “Test Pass” will be displayed when the test passes (Figure 6) and “Test Failed” will be displayed
when the test fails (Figure 7).
Figure 6 Figure 7
4.2 User-defined pressure test
1. Enter the Main Menu and use the UP/DOWN button to select Air Pressure Test (Figure 1), press the
ENTER button to confirm, press the MENU button to exit.
Figure 1
7C

2. Enter the Test Menu and use the UP/DOWN button to select Manual Setting (Figure 2),press the
ENTER button to confirm. Adjust the parameters of the time and pressure on the Manual Setting page
(Figure 3), press the ENTER button to restore and the system will automatically return to the Test
Menu.
Figure 2 Figure 3
3. Enter the Test Menu and use the UP/DOWN button to select Vacuum Test (Figure 4) or Pressure
Test (Figure 5) as needed, press the ENTER button to confirm, press the MENU button to exit.
Figure 4 Figure 5
4. Enter into the test page (Figure 6, Figure 7) and press the green button to start testing.
Figure 6 Figure 7
8C

5. If there is any problem during the test, please press the red button to stop the test.
6. “Test Pass” will be displayed when the test passes (Figure 8) and “Test Failed” will be displayed
when the test fails (Figure 9).
Figure 8Figure 9
4.3 Air leakage test
1. Enter into the Main Menu and use the UP/DOWN button to select Air Leakage Test (Figure 1), press
the ENTER button to confirm, press the MENU button to exit.
Figure 1
9C