Akuvox R26X User manual

R26X
Quick Guide
M4x20 screw x 2
ST4x20 screw x 4
Screw fixing seat x 4
M3x10 screw x 1
M3x5 screw x 4
Cable buckle x 1
Back cover x 1
R26X x 1
Wall bracket x 1
Please make sure the package contains the following items:
Unpacking

R26X
Speaker
RF card reader
Call button
Status LED
Thermal sensor
Photosensitive sensor
Infrared LED
Mic
Camera
R26C
Product Overview

R26X
Infrared LED
Thermal sensor
Photosensitive sensor
Camera
Speaker
Call button
Status LED
Mic
R26P

R26X

R26X
With 86 embedded box in the wall :
Installation
Wall Bracket Installation
Use 2 M4X20 screws to
fix the wall bracket and
embedded box.
Use the pen to mark
the hole location on
the wall bracket
Take down the
M4x20 screws and
remove the wall
bracket
Use 6mm Drill to drill
the red hole you
marked before
Insert the screw fixing seat
into the hole
Use 4 ST4x20 screws
and 2 M4x20 screws
to fix the wall
bracket

R26X
Without 86 embedded box in the wall :
Use the pen to mark the
hole location on the wall
bracket
Use 6mm Drill to drill the
red hole you marked
before ,and dig a 5cm
depth square hole
Insert the screw fixing seat
into the hole
Use 4 St4X20 screws to fix
the wall bracket

R26X
Back cover Installation
Take down the back
cover ,cable buckle.
Make cables go through all the
components of the bottom hole ,
connect with the contacts in the main
board. Then put the cable buckle and
sealing ring into the back cover.
Use 4 M3x5 screws to fix
the back cover

R26X
Device Mounting
1. Insert the screws
of R26X into the
holes on the wall
bracket
2. Push down to fix the
device securely.
3. Lock the M3X10
screw at the bottom
of device.

R26X
Interface Description On PCB Board:

R26X
LAN
PoE
R26P
R26C
R47
PoE
PoE
Network Video Recorder
(third party)
PC
(third party)
PoE
PoE
R26P
R26C
Application Network Topology
Application Network Topology

R26X
Configuration
1. Access the Web UI: Input the IP address into browser to configure the
phone. The default IP address is 192.168.1.100.
2. Account Registration: On web UI, go to the path: Account -> Basic page
Register Account and fill in the account information. (Please refer to user
manual for more information)
3. Configure the Push Button: On web UI, go to the path: Intercom ->
Basic -> Push Button to configure the call number.
4. Configure the code to open the relay: On web UI, go to the path:
Intercom -> Relay&Input -> Relay ID/DTMF and choose the DTMF code
number in corresponding area.
IP Announcement
1. While R26X is startup normally, hold the call button for several seconds
after the LED light turns blue, voice system will enter IP announcement
mode.
2. In announcement mode, the IP address will be announced periodically.
3. Press Call Button again to the announcement mode.
4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address
is gained.
Operation
Make a call:
1. Press the call button to call indoor SIP Phone.
2. During the talk, called party can press pre-configured code number to
unlock the door.
Receive a call:
R26X supports Auto Answer by default. Incoming call from indoor
device will be answered automatically.

R26X
Name
Status
Description
Status
indicator
Blue
Normal status
Calling
Red
Restarting
Network is unavailable
Green
Initialing/Talking on a call
Receiving a call
Red/Blue
Firmware upgrading
Indicators
Note: For more LED settings, please refer
to R26X webUI: Intercom -> LED Setting.
Notice Information
Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without
notice, any update to this document can be viewed on Akuvox’ s website: http://www.akuvox.com © Copyright 2016 Akuvox Ltd. All rights reserved.
: Light ON
: Light OFF
0.25sec
0.25sec
0.25sec
0.25sec
0.25sec
0.25sec
0.05sec
0.05sec
0.05sec
0.05sec