Allsteel Harvest User manual

3430391900
Standing Height Table
Seated Height Table
Pour des instructions en francias, appelar le 800-822-7653
Para instrucciones en enspanol, llame al 800-822-7653
Harvest Metal Table
Installation Instructions
03/22/2019

3430391900Page 2 of 14
Harvest Metal Table Installation Packet
#12 x 1” Wood Screw 5/16” - 18 X 7/8”
Button head screw
black
#8 x 1/2” Wafer head
screw
1/4”-20 X 3/4”
Truss head machine screw
5/16” Glide
3/4” wide galvanized steel
Loop clamp
Plastic clip
Drill
No. 2 Phillips head screwdriver bit
No. 3 Phillips head screwdriver bit
Extra long Phillips head screwdriver bit
#2 Magnetic tip hex drive drill
1/4” driver
3/16” Hex Head Bit
Hardware - Total Quantities Shown
x32
x40
x40
x2
x32
x4
x9
x9
x100
#10 x 1 Hex head
Self drilling screw
Standing Height Tables
1/4” - 20 x 3/4” Truss Head Screw - Bag #1
#12 - 8 Pan Head Screw - Bag #2
#10 - 16 x 1” Hex Head Self Drilling - Bag #3
#8 x 1/2” Wafer Head Screw - Bag #4
5/16” - 18 x 7/8” Button Head Screw -Bag #5
#10 x 7/8” Hex Head Screw
Seated Height Tables
1/4” - 20 x 3/4” Truss Head Screw - Bag #1
#12 - 8 Pan Head Screw - Bag #2
#10 - 16 x 1” Hex Head Self Drilling - Bag #3
#8 x 1/2” Wafer Head Screw - Bag #4
#10 x 7/8” Hex Head Screw
#10 X 1-1/2” Philips
wafer head
Hardware Bags
Tools
x40
#10 x 7/8”
Hex Head Screw

Page 3 of 14 3430391900
Harvest Metal Table Installation Packet
Build Staging
1. Protect worksurface by clearing the build area of any debris that can cause damage.
2. Place worksurafce upside down (as shown) on packing blankets or equivalent to protect
upward facing show surface during the installation process.
3. Open up hardware pack and lay out the numbered bags within.
Build table with underside
facing up.
Protect show surface
and edges of the top
SCALE 0.500
SCALE 1.000
Note - Legs and corner brackets are left and right hand specic.
1. Attach corner brace to leg with (2) 1/4”-20 X 3/4” machine screws.
2. Align leg bracket with worksurface pilot holes. Start by installing (1) #12X1” wood screw into
pilot hole #1. Verify that leg reveal is square with worksurface, make adjustments if needed.
Install remaining 2 wood screws into pilot holes.
3. Repeat steps for all legs.
x8
x12
Leg Assembly
Machine
Screws
Corner Brace
Pilot Holes
Hardware:
Leg Reveal
Both Sides

3430391900Page 4 of 14
Harvest Metal Table Installation Packet
Staging Electrical
1. Place all electrical components as shown below. Allow wiring to run through cord slots prior
to center support channel being installed.
2. Power will run down one leg. Place cord/conduit through cord slots closest to preferred leg with
plug/conduit hanging on the corner brace.
Cord Slots Electrical Boxes
1. Align center support channel across the length of the table shown in Illistration 1.
2. Install (3) #8-18X1/2” PHL Wafer screws through the corner brace into the support channel.
Each channel is connected on both ends.
Center
Support Channels
Corner Brace
Wafer screws
x12
Center Support Channels
Hardware:

Page 5 of 14 3430391900
Harvest Metal Table Installation Packet
1. Finish Installing leg assembly with (7) #12x1” wood screws into the workurface
2. Repeat for all legs.
x28
Hardware:
Note: Electrical must be moved
aside to access all screw holes
Leg Assembly continued...
x8
Hardware:
Anti-Bow Brackets
Center
Support Channel
Anti-Bow
Bracket
6”
1. Mount anti-bow bracket into cavity of center support channels, and 6” away from each end.
2. Fasten each bracket to worksurface with (1) #12 x 1” wood screw. Repeat on both sides.
3. Mount remaining anti-bow brackets evenly across each support channel and attach to surface.

3430391900Page 6 of 14
Harvest Metal Table Installation Packet
SCALE 0.700
SCALE 0.550
Wood screw
locations
4. Align electrical module into the corner electrical bracket as shown.
5. Install (4) #12X1” wood screws to fully secure the corner unit.
6. Repeat for all legs.
1. With electrical box slid towards Center Support Channel, attach corner electrical bracket with
(1) #12x1” wood screw into the front location circled below.
2. Slide electrical box forward and install (2) #12x1” remaining rear wood screws.
3. Repeat for all legs.
SCALE 0.550
Front Screw
SCALE 0.500
Corner electrical
bracket
Electrical Box
slid forward
Corner electrical
bracket
x28
Hardware:
Corner Electrical
Slide
Back
Rear
Screws

Page 7 of 14 3430391900
Harvest Metal Table Installation Packet
1. Align center electrical shroud with pilot holes in the center of the table. Attach using (2)
#12 x 1” wood screws as shown below.
2. Mount center electrical box into shroud until fully seated. Attach module with (2) #8 x 1/2”
Wafer head screws.
x4
Hardware:
x12
3. Place electrical cover plates between the center electrical box and shroud, keeping the back
of the plates ush with center support channels.
4. Attach cover plates to electrical shroud with (4) #8 x 1/2” Wafer head screws
5. Repeat all steps for opposite side of table.
Center Electrical
Wafer Head
Screws
Electrical Shroud
Center
Electrical Box
Electrical
Cover Plates

3430391900Page 8 of 14
Harvest Metal Table Installation Packet
Center Electrical Junction Box - Corded
Center Electrical Junction Box - Hardwired
1. Align junction box on the center of the worksurface, between the cord slots as shown below.
Attach junction box with (2) #12 x 1” wood screws.
Center
Cord Slots
x2
Hardware:
1. Align junction boxes in the center of the worksurface, as shown below. Attach to worksurface
with (4) #12 X 1” wood screws.
Hardwired junction
boxes to be attached
by electrician.
x4
Hardware:

Page 9 of 14 3430391900
Harvest Metal Table Installation Packet
External Stiffeners
1. Place rst stiffener along row of anti-bow brackets, with one end 2-5/8“ from the surface edge.
Attach stiffener to surface with (2) #10 x 7/8 Hex head screws into outer-most holes of stiffener.
2. Place second stiffener along inside wall of st stiffener, with end 2-5/8” from opposite surface
edge than the rst stiffener. Attach with (2) #10 x 7/8 Hex head screws into outer-most holes.
3. Finish installing external stiffeners with (16) #10 x 7/8 Hex head screws.
4. Repeat steps 1-3 for 2 remaining stiffeners on other half of worksurface.
x9
Hardware:
x9
5. Attach all cords/conduit to bottom of surface using (9) loop clamps and (9) #12 x 1” wood screws.
Excess cords must be placed between external stiffeners.
x40
Outermost
Screw
External
Stiffener
Excess
Cords
25/8

3430391900Page 10 of 14
Harvest Metal Table Installation Packet
External Siffeners - 36” Wide Variant
Note - The external stiffeners on 36” wide Harvest Tables differ from the standard mounting method.
Place largest stiffeners over
top of Anti-bow Brackets.
(Remove screws)
Place smallest stiffeners
centered on the surface,
2 5/8” from each edge.
25/8

Page 11 of 14 3430391900
Harvest Metal Table Installation Packet
SCALE 0.500
SCALE 0.600
SCALE 0.520
SCALE 0.650
Shelves
1. Mount shelves into place over electrical and support channels. Route cord/conduit
out of clearance notch of shelf next to chosen leg.
2. Align pilot holes in shelves with holes on the left and right hand corner electrical plates,
as well as corner brace holes. Use (8) 1/4-20 x 3/4” zinc plated screws per shelf.
3. Attach shelf to center electrical with (4) 1/4-20 x 3/4” zinc plated screws per shelf.
1/4-20 x 3/4”
zinc plated screws
Clearance Notch
#10 x 1-1/2”
pan head screw
#10-16 x 1”
Self-Drilling Screw
x24
x2
Hardware:
x36
Leave end screw
out until next step
Shelves
4. Fasten center electrical to shelf using (1) #10 x 3/4” pan head screw per shelf.
5. Fasten shelves to support channels with #10-16 x 1” self-drilling screws. (Qty varies)
Corner Electrical Center Electrical

3430391900Page 12 of 14
Harvest Metal Table Installation Packet
1. Install leveling glides into threaded insert on each leg.
2. Attach foot rest to legs with (8) 5/16”-18 x 7/8” button head screws. Repeat for opposite end.
3. Place foot rail between foot rests and install (4) 5/16”-18 x 7/8” button head screws into each
end. Repeat for remaining foot rail.
SCALE 0.500
Glide
1. Mount apron over shelves, install (2) #10 X 16 X 1” self-drilling screws into support channels.
2. Install (8) #8-18 x 1/2” PHL waferhead screws into shelves.
3. Repeat for opposite end.
x16
Hardware:
x4
5/16”-18 x 7/8”
Button Head Screws
Foot Rail
Foot Rest
x32
Hardware:
SCALE 0.100
Reference view
x4
Apron
Aprons
SCALE 0.500
Foot Rest & Foot Rail (standing height only)
Foot Rest

Page 13 of 14 3430391900
Harvest Metal Table Installation Packet
1. Once fully assembled, lift and rotate the table to the upright position.
2. Check legs to make sure that they are perpendicular to the oor.
3. Level table.
Build view Stand view
Wire
Management
Trough
1. Run cord/conduit from shelf through wire management trough.
2. Attach adhesive tape to trough on face shown below.
3. Adhere tape/trough directly to leg, keeping the outward facing surface ush with apron.
Top View
Apply adhesive
tape to this surface
Flip Table Upright
*Important*
Table should be rolled by at least two installers. Table should be lifted while ipping due
to the overall weight. Failure to adequately support table may result in damage to legs.
Wire Management Trough
This face to be
ush with apron

3430391900Page 14 of 14
Harvest Metal Table Installation Packet
Final Assembled Table
Exploded View