Allsteel Laminate Casegoods User manual

Laminate Casegoods
Installation Instructions
Pour des instructions en francias, appelar le 800-822-7653
Para instrucciones en enspanol, llame al 800-822-7653 343-3942A
Index
General Guidelines ....................2
Knock Down Units .....................3
General Installation ...................11
Drawer, Door and Shelf Adjustments. . . . . . 12
Credenza Installation..................16
Worksurface Installation ...............19
Desking Installation ...................19
Modesty Panel Installation .............20
Height Adjustable. . . . . . . . . . . . . . . . . . . . . 27
Large Height Adjustable ...............30
Wall Mount Overhead Installation ........33
Panel Mount Overhead Installation ......34
Support Installation ..................35
Stacking Storage ....................37
Accessories .........................38
WKAPE-E
Allsteel Inc.
Muscatine, Iowa 52761-0071
www.allsteelofce.com

Wire Trough
1. If necessary to turn a unit on its back or side, ensure that the oor is clean
and free of debris which may scratch the unit.
2. Attachment hardware is provided in hardware packs unless otherwise noted.
3. Do not move unit using wire trough as a handle.
General Usage Notes:
Laminate Casegoods Installation Packet
Failure to install product as instructed, use of hardware other than that which is provided, or failure to comply
with instructions can result in product failure, personal injury, or property damage.
WARNING
343-3942A
(8/16)
Pages 2 of 39

x
y
z
ACS0
x
y
zACS0
x
y
zACS0
Arrow
Minix Cam
End Panel
Minix Bolt
Shoulder
Minix Bolt
Dowel
Minix Cam
Arrow
Minix Cam
Minix Bolt
Dowel
Glide Insert
Dowel
NOTE: Orientation of the holes. Lay end panel as shown,
with holes up, on cardboard or a carpeted surface.
NOTE: Orientation of the holes. Lay end panel as shown,
with holes up, on cardboard or a carpeted surface.
Step 1 - Use a rubber mallet to install dowels onto end
panel as shown.
Step 2 - Use a Phillips screwdriver to install minix
bolts onto end panel. Tighten each minix
bolt until minix bolt shoulder is ush against
surface of front panel.
Step 3 - With arrows facing the edge of the end panel,
install minix cams into holes along long side
of panel.
Step 4 - With arrows facing the edge of the
shelves, install minix cams into holes
along long side of remaining shelves
and bottom panel.
Step 5 - Use the rubber mallet to install glide
insert into each hole.
Step 6 - Use a rubber mallet to install dowels onto front
panel as shown.
Step 7 - Use a Phillips screwdriver to install minix
bolts onto front panel. Tighten each minix
bolt until minix bolt shoulder is ush against
surface of front panel.
Illustration 1. Side Access Tower Assembly
1a.
1c.1b.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 3 of 39

NOTE: Do not fully tighten glide. Fully tightening
glide will cause glide insert to pull out of bottom shelf.
NOTE: Ensure holes in bottom of shelf are facing the
same direction as bottom edge of end panel and rear
edges of shelf and end panel are aligned.
Step 11 - Attach front panel made in Step 6 & 7 to
end panel with the shelf assembly by
inserting minix bolts, into holes drilled into
sides of end panel and the shelf assembly.
Step 12 - Use a Phillips screwdriver to tighten minix
cam. Turn minix cams clockwise to tighten.
Step 13 - Use a Phillips screwdriver to install
screws into glide plate into each hole.
Step 15 - Use a Phillips screwdriver to install
screws into coat hooks into each hole.
Step 8 - Attach shelf to end panel by inserting minix
bolts, attached to end panel, into holes drilled into
side of shelf.
Step 9 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Step 10 - Repeat Steps 8-9 for remaining shelves and
bottom panel.
Step 14 - Thread a glide leveler into glide
insert. Turn glides clockwise until
glides are at against glide inserts.
Step 16 - Install adhesive covers onto exposed
minix cam connectors.
1e. 1f.
1g. 1h.
Illustration 1. Side Access Tower Assembly Continued
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 4 of 39

NOTE: Orientation of the holes. Lay panels as shown,
with holes up, on cardboard or a carpeted surface.
Step 1 - Use a rubber mallet to install
dowels as shown.
Step 2 - Use a Phillips screwdriver to
install minix bolts. Tighten
each minix bolt until minix
bolt shoulder is ush against
surface.
Step 3 - With arrows facing the edge,
install minix cams.
Step 4 - Use a Phillips screwdriver to
install keku fasteners.
Step 5 - Attach right hand and left hand end panels onto
horizontal crosstie by inserting minix bolts, into
holes drilled into side of crosstie.
Step 6 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Step 7 - Attach lower front panel onto end panels and
crosstie by inserting minix bolts, into holes
drilled into side of crosstie and end panels.
Step 8 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Illustration 2. Wall Access Panel Assembly
2a.
2c.2b.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 5 of 39

NOTE: Trough will also attach to the worksurface.
Reference support section for instructions on aligning
to credenzas and worksurfaces.
NOTE: This part can be left off until after desk is set-up. This part
is designed to be removed by the end-user to access wiring.
Step 9 - Bend tab on wire trough 90 degrees.
Step 10 - Install screws to attach wire trough onto
assembly.
Step 11 - Install upper front panel by
snapping the 4 keku fasteners
together
Illustration 2. Wall Access Panel Assembly Continued
2d.
2e.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 6 of 39

NOTE: Orientation of the holes. Lay panels as shown,
with holes up, on cardboard or a carpeted surface.
Step 1 - Use a rubber mallet to install
dowels as shown.
Step 2 - Use a Phillips screwdriver to
install minix bolts. Tighten
each minix bolt until minix
bolt shoulder is ush against
surface.
Step 3 - With arrows facing the edge,
install minix cams.
Step 4 - Attach crosstie and front panels onto short end
panel by inserting minix bolts, into holes drilled
into side of crosstie.
Step 5 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Step 6 - Attach long end panel to assembly by inserting
minix bolts into holes drilled into side of crosstie.
Step 7 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Step 8 - Use a Phillips screwdriver to install screws
into glide plate into each hole.
Illustration 3. False Pedestal Assembly
3a. 3b
3c. 3d.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 7 of 39

NOTE: Trough will also attach to the worksurface.
Reference support section for instructions on aligning
to credenzas and worksurfaces.
Step 9 - Bend tab on wire trough 90 degrees.
Step 10 - Install screws to attach wire trough onto
assembly.
Illustration 3. False Pedestal Assembly Continued
3e.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 8 of 39

Step 1 - Use a rubber mallet to install
dowels as shown.
Step 2 - Use a Phillips screwdriver to
install minix bolts. Tighten
each minix bolt until minix
bolt shoulder is ush against
surface.
Step 3 - With arrows facing the edge,
install minix cams.
Step 4 - Attach back panel onto bottom panel by inserting
minix bolts into holes drilled into side of the
bottom panel.
Step 5 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Step 6 - Attach right and left end panel to assembly by
inserting minix bolts, into holes drilled into side
of crosstie.
Step 7 - Use a Phillips screwdriver to tighten minix cam.
Turn minix cams clockwise to tighten.
Illustration 4. Cubby Assembly & Installation
4a.
4c.4b.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 9 of 39

Step 9 - Score a line along the inside of each end panel
from the front of the cubby end panel to the back.
Step 10 - Measure (1 1/8”) from the front of the cubby and
mark the front of the rst bracket.
Step 11 - Measure (9 7/8”) from the front of the cubby and
mark the front of the second bracket.
Step 8 - Align cubby end panel in desired position. Step 12 - Repeat steps 10 and 11 for the brackets on the
other side.
Step 13 - Align the brackets to sit along the marks and
install into the bottom of the worksurface.
Step 14 - After all four brackets are installed, install cubby
with all four brackets in the inside of the unit and
insert screws into the pilot holes of the cubby.
Illustration 4. Cubby Assembly & Installation Continued
4d.
4f.
4e.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 10 of 39

NOTE: When possible, locate the highest point of the oor and start leveling from there.
On carpeted oors, be sure the glides are supporting the weight of the unit. If tipping the
credenza is necessary, be aware of the drawers and shelves opening or falling.
Bar Pulls: Two sizes are used for different units
Hinged Doors use 7” Bar Pulls
Drawer units 18”W or larger use 14” Bar Pull
Drawer units under 18”W use the 7” Bar Pull
Exception: WKCLFN5H30xxxx-CFL
Arch & Square Pulls: One size used on all units.
Step 1 - Place credenza as close to nal location as possible.
Step 2 - Level the credenza from side to side and front to back.
When possible use a level across the credenza.
Step 3 - Credenza should be ush to adjoining credenza both
on the front edge and the top side.
Step 1 - Fully open door or drawer.
Step 2 - Position pull to line up
with pre drilled holes.
Step 3 - Use screws provided to
attach pulls.
Illustration 5. General Installation
5a. Level Credenza
Illustration 5. General Installation Continued
5b. Pulls
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 11 of 39

SCALE 0.250
SCALE 0.250
Box Drawer
File Drawer Retaining Tab
Retaining Tab
Drawer Slide
Set Screw
Step 1 - Loosen screws on drawer slide.
Step 2 - Adjust drawer for even reveal.
Step 3 - Tighten screws taking care not to over tighten
Step 1 - Unload drawer and fully extend drawer.
Step 2 - Locate retaining tabs on each drawer side.
They are centered along the length of the
slide. Press rmly on retaining tabs and pull
drawer forward until free of credenza.
Step 1 - Unload drawer and fully extend drawer.
Step 2 - Remove set screws from drawer slides.
Step 3 - Locate retaining tabs on the top front of each
drawer side. Press rmly on retaining tabs and
lift up on front of drawer. Slide drawer forward
and lift free of credenza.
Illustration 6. Drawer, Door and Shelf Adjustments
6a. Drawer Adjustment
6b. Box Drawer Removal 6c. Lateral and File Drawer Removal
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 12 of 39

343-2950B (06/14)
Page 17 of 54
Involve Installation Packet
Illustration 21. Door Hinge Adjustment
Door Side-To-Side Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door out or counterclockwise to adjust door in.
Door Depth Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate hinge mounting screw on door hinge
assembly.
Step 3 – Use the Phillips screwdriver to loosen
(but do not remove) the hinge mounting screw.
Step 4 – Adjust alignment of door and retighten hinge
mounting screw.
Door Height Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door down or counterclockwise to adjust door
up.
Note: Hinge plate may be slotted and require
adjustment by loosening screws.
343-2950B (06/14)
Page 17 of 54
Involve Installation Packet
Illustration 21. Door Hinge Adjustment
Door Side-To-Side Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door out or counterclockwise to adjust door in.
Door Depth Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate hinge mounting screw on door hinge
assembly.
Step 3 – Use the Phillips screwdriver to loosen
(but do not remove) the hinge mounting screw.
Step 4 – Adjust alignment of door and retighten hinge
mounting screw.
Door Height Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door down or counterclockwise to adjust door
up.
Note: Hinge plate may be slotted and require
adjustment by loosening screws.
343-2950B (06/14)
Page 17 of 54
Involve Installation Packet
Illustration 21. Door Hinge Adjustment
Door Side-To-Side Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door out or counterclockwise to adjust door in.
Door Depth Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate hinge mounting screw on door hinge
assembly.
Step 3 – Use the Phillips screwdriver to loosen
(but do not remove) the hinge mounting screw.
Step 4 – Adjust alignment of door and retighten hinge
mounting screw.
Door Height Hinge Adjustment
Step 1 – Fully open cabinet doors.
Step 2 – Locate door alignment screw on door
hinge assembly.
Step 3 – Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 – Turn door alignment screw clockwise to adjust
door down or counterclockwise to adjust door
up.
Note: Hinge plate may be slotted and require
adjustment by loosening screws.
NOTE: Hinge plate may be slotted and require
adjustment by loosening screws.
Step 1 - Fully open cabinet doors.
Step 2 - Locate door alignment screw on door hinge
assembly.
Step 3 - Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 - Turn door alignment screw clockwise to adjust
door out or counterclockwise to adjust door in.
Step 1 - Fully open cabinet doors.
Step 2 - Locate hinge mounting screw on door hinge
assembly.
Step 3 - Use the Phillips screwdriver to loosen (but do
not remove) the hinge mounting screw.
Step 4 - Adjust alignment of door and re-tighten hinge
mounting screw.
Step 1 - Fully open cabinet doors.
Step 2 - Locate door alignment screw on door hinge
assembly.
Step 3 - Use the Phillips screwdriver to adjust door
alignment screw.
Step 4 - Turn door alignment screw clockwise to adjust
door down or counterclockwise to adjust door
up.
Illustration 6. Drawer, Door and Shelf Adjustments Continued
6d. Door Hinge Adjustment
6e. Door Depth Hinge Adjustment
6f. Door Height Hinge Adjustment
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 13 of 39

343-2950B (06/14)
Page 18 of 54
Involve Installation Packet
Note: Door removal should only be necessary to
replace a damaged door.
Step 1 – Press hinge catch at rear of hinge
mounting plate (attached to door hinge
support).
Step 2 – While pressing hinge catch, pivot rear of
hinge away from hinge mounting plate.
Step 3 – Pull forward on hinge until hinge
mounting hooks come free of mounting
plate lugs.
Step 4 – Repeat procedure for remaining hinge.
Step 5 – Reinstall door by reversing this
procedure.
Step 1 – Push forward on hinge until the
mounting hooks contact the
mounting plate lugs.
Step 2 – When the mounting hooks engage
the mounting plate lugs, press the
rear of the hinge toward the mounting
plate until it latches with the catch.
Illustration 22a. Hinge Door Removal and Installation – Hinge Door Removal
Illustration 22b. Hinge Door Removal and Installation – Hinge Door Installation
Hinged Door Removal
Lug
Hinge
Mounting
Plate
Hinge Mounting
Plate
Mounting Hook
Hinge
Hinge
Cabinet
Door
Cabinet
Door
Catch
Hinged Door Installation
Lug
Hinge
Mounting
Plate
Hinge Mounting
Plate
Mounting Hook
Hinge
Hinge
Cabinet
Door
Cabinet
Door
Catch
343-2950B (06/14)
Page 18 of 54
Involve Installation Packet
Note: Door removal should only be necessary to
replace a damaged door.
Step 1 – Press hinge catch at rear of hinge
mounting plate (attached to door hinge
support).
Step 2 – While pressing hinge catch, pivot rear of
hinge away from hinge mounting plate.
Step 3 – Pull forward on hinge until hinge
mounting hooks come free of mounting
plate lugs.
Step 4 – Repeat procedure for remaining hinge.
Step 5 – Reinstall door by reversing this
procedure.
Step 1 – Push forward on hinge until the
mounting hooks contact the
mounting plate lugs.
Step 2 – When the mounting hooks engage
the mounting plate lugs, press the
rear of the hinge toward the mounting
plate until it latches with the catch.
Illustration 22a. Hinge Door Removal and Installation – Hinge Door Removal
Illustration 22b. Hinge Door Removal and Installation – Hinge Door Installation
Hinged Door Removal
Lug
Hinge
Mounting
Plate
Hinge Mounting
Plate
Mounting Hook
Hinge
Hinge
Cabinet
Door
Cabinet
Door
Catch
Hinged Door Installation
Lug
Hinge
Mounting
Plate
Hinge Mounting
Plate
Mounting Hook
Hinge
Hinge
Cabinet
Door
Cabinet
Door
Catch
NOTE: Door removal should only be necessary to
replace a damaged door.
Step 1 - Press hinge catch at rear of hinge mounting
plate (attached to door hinge support).
Step 2 - While pressing hinge catch, pivot rear of hinge
away from hinge mounting plate.
Step 3 - Pull forward on hinge until hinge mounting
hooks come free of mounting plate lugs.
Step 4 - Repeat procedure for remaining hinge.
Step 5 - Reinstall door by reversing this procedure.
Step 1 - Push forward on hinge until the mounting
hooks contact the mounting plate lugs.
Step 2 - When the mounting hooks engage the
mounting plate lugs, press the rear of the
hinge toward the mounting plate until it latches
with the catch.
Illustration 6.Drawer, Door and Shelf Adjustments Continued
6g. Hinge Door Removal
6h. Hinge Door Installation
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 14 of 39

SHELF ADJUSTMENT
242-0090F
SIDE 4 OF 4 (11/13)
ADJUSTMENT INSTRUCTIONS
Read all instructions and review illustrations
before installing.
Tools required for assembly:
Phillips screwdriver
Cordless drill
Phillips driver
Shelf Adjustment:
1. Fully open cabinet doors.
2. Refer to Illustration 9. Using Phillips screw-
driver, loosen shelf by turning shelf fasteners 1/2
turn counter-clockwise or until loose.
3. Lift shelf off fastener pins and set aside.
4. Refer to Illustrations 9 and 10. Remove fastener
pins from holes and insert at desired position.
Ensure all four pins are installed at same height.
5. With notches down, position the shelf onto the
fastener pins. Ensure fastener pins are seated
into the shelf fasteners in bottom of adjustable
shelf.
6. Using Phillips screwdriver, tighten shelf by turn-
ing shelf fasteners 1/2turn clockwise or until fully
locked on pins.
Illustration 9
Shelf
Shelf
fastener
Illustration 10
Fastener
pin
Adjustment
holes
Illustration 11
Screw
Shelf
Shelf clip
Shelf Adjustment - Alternate Mounting (refer to
Illustration 11):
1. Locate screws securing shelf to shelf clips.
2. Use the cordless screwdriver and phillips driver
to remove screws. Discard screws (screws are
installed for shipping purposes and are not
required for normal use of bookcase).
3. Remove shelf from bookcase.
4. Remove shelf clips from adjustment holes in
bookcase wall.
5. At the desired shelf location, reinstall shelf clips
into adjustment holes. Ensure shelf clips are
reinstalled at the same height.
6. Reinstall shelf onto shelf clips.
SHELF ADJUSTMENT
242-0090F
SIDE 4 OF 4 (11/13)
ADJUSTMENT INSTRUCTIONS
Read all instructions and review illustrations
before installing.
Tools required for assembly:
Phillips screwdriver
Cordless drill
Phillips driver
Shelf Adjustment:
1. Fully open cabinet doors.
2. Refer to Illustration 9. Using Phillips screw-
driver, loosen shelf by turning shelf fasteners 1/2
turn counter-clockwise or until loose.
3. Lift shelf off fastener pins and set aside.
4. Refer to Illustrations 9 and 10. Remove fastener
pins from holes and insert at desired position.
Ensure all four pins are installed at same height.
5. With notches down, position the shelf onto the
fastener pins. Ensure fastener pins are seated
into the shelf fasteners in bottom of adjustable
shelf.
6. Using Phillips screwdriver, tighten shelf by turn-
ing shelf fasteners 1/2turn clockwise or until fully
locked on pins.
Illustration 9
Shelf
Shelf
fastener
Illustration 10
Fastener
pin
Adjustment
holes
Illustration 11
Screw
Shelf
Shelf clip
Shelf Adjustment - Alternate Mounting (refer to
Illustration 11):
1. Locate screws securing shelf to shelf clips.
2. Use the cordless screwdriver and phillips driver
to remove screws. Discard screws (screws are
installed for shipping purposes and are not
required for normal use of bookcase).
3. Remove shelf from bookcase.
4. Remove shelf clips from adjustment holes in
bookcase wall.
5. At the desired shelf location, reinstall shelf clips
into adjustment holes. Ensure shelf clips are
reinstalled at the same height.
6. Reinstall shelf onto shelf clips.
Adjustment Screw
Lower Guide
Adjustment
Tab
Upper
Guide
Step 1 - Use a at blade screwdriver to turn adjustment
screw to raise/lower door. The adjustment
screw has ve pre-set positions of adjustment
for both raising and lowering the door.
Step 2 - When raising/lowering door it may be
necessary to raise or lower the upper guide
in the upper track. Press on adjustable tab on
upper guide and move up/down as required.
The upper guide has three positions: fully
extended, half extended and fully retracted.
Step 1 - Fully open cabinet doors.
Step 2 - Using Phillips screwdriver, loosen shelf by
turning shelf fasteners 1/2 turn counter-
clockwise or until loose.
Step 3 - Lift shelf off fastener pins and set aside.
Step 4 - Remove fastener pins from holes and insert
at desired position. Ensure all four pins are
installed at same height.
Step 5 - With notches down, position the shelf onto the
fastener pins. Ensure fastener pins are seated
into the shelf fasteners in bottom of adjustable
shelf.
Step 6 - Using Phillips screwdriver, tighten shelf by
turning shelf fasteners 1/2 turn clockwise or
until fully locked on pins.
Illustration 6. Drawer, Door and Shelf Adjustments Continued
6i. Sliding Door Adjustment for Reveal
6j. Shelf Adjustment
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 15 of 39

42-2730F
Counterweight Kit
2 OF 3
Illustration 6
Illustration 5
Counterweight
Counterweight
Tape and
paper backing
Counterweight
Flange
Front of
Credenza
Back of
Credenza
Illustration 4
File
Drawer
Slide Flathead
Screwdriver
File Drawer: Refer to Illustration 4. With drawer fully
extended, grasp top of either drawer side in the middle,
between thumb and forefinger.
Apply inward pressure at top of drawer side and pull
top of drawer side towards the middle of the drawer
while pulling up on the drawer side.
While pressure is being applied, insert a flat blade
screwdriver or a heavy duty putty knife between the
slide and the drawer side. Leverage the slide away
from the drawer side in the suspension slide.
Repeat steps 1, 2 and 3 for the opposite side and lift
drawer up out of the suspension slide.
2. Remove the wood slabs that are surrounding the
counterweight kit.
3. Refer to the counterweight matrix to determine how
much weight is needed in unit.
4. Refer to Illustration 5. Wear work gloves when han-
dling counterweight. Remove paper backing from
mounting tape attached to rear of counterweight.
5. Refer to Illustration 6. With mounting tape facing
towards rear wall of credenza and running parallel
with bottom surface of credenza, place bottom edge of
counterweight onto the rear wall of the credenza, mak-
ing sure that the bottom edge of the counterweight is
sitting on the flange, and that the back of the counter-
weight is adhered to the back of the credenza.
HINT: It may be easier to place the counterweight kit
into the credenza if the credenza is laid flat onto its
back.
42"W
Combo Unit
48"W
Combo Unit
60"W
Combo Unit
72"W
Combo Unit
24"W
Box/File Unit
30"W
Box/File Unit
36"W
Box/File Unit
25 lbs. 25 lbs. 35 lbs. 35 lbs. 35 lbs. 50 lbs. 50 lbs.
HSCACW25 HSCACW25 HSCACW35 HSCACW35 HSCACW35 HSCACW50 HSCACW50
(2 of the
12.5 lb
weights)
(2 of the
12.5 lb
weights)
(2 of the
12.5 weights
and 2 of the
5 lb
weights)
(2 of the
12.5 weights
and 2 of the
5 lb
weights)
(2 of the 12.5
weights and
2 of the 5 lb
weights)
(4 of the 12.5
lb weights)
(4 of the 12.5
lb weights)
18"D
COUNTERWEIGHT MATRIX
NOTE: Do not put more than 4 counterweights deep.
If more counterweight is required, add to the
back side of the inset back.
Step 1 - Remove all drawers in unit as described in
Illustration 6b and 6c.
Step 2 - Remove counterweight from packaging
Step 3 - Install counterweight with tape facing rear wall
of credenza and running parallel with bottom
surface. Ensure that the bottom edge is sitting
on the bottom panel of the credenza.
Illustration 7. Counterweight Installation
7a. 7b.
7c.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 16 of 39
Full drawers can be very heavy. To avoid injury, remove contents before removing drawer.
Lifting a drawer with a drawer accessory (hang rails, dividers, or followers) can cause the drawer accessory
to come loose. The drawer can fall and cause serious injury to you or others. Lift drawer by a xed part of the drawer.
Sharp edges may cause injury. Take care when handling metal parts.
Counterweight is heavier than it appears and may be hard to control when handling. Take care when handling
counterweight or severe personal injury may result.
WARNING

NOTE: Top drawers will have to be removed
if the unit has them.
Step 1 - Remove trough from the unit. Save screws to
be used in step 2.
Step 2 - Install new trough that was included in nished
back kit by screwing into the top of the unit and
into the end panels.
Step 3 - Install hardware (pins and dowels, raxes)
to nished back, add cams to bottom of
credenza, add rax pins to end panels.
Step 4 - Insert the pins and dowels into corresponding
holes on the backside of the credenza bottom.
Step 5 - Tilt the nished back upright to install the
raxes into the rax pins.
Illustration 8. Finished Back Installation
8a. 8b.
8c. 8d.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 17 of 39

Step 7 - Tighten cams on the bottom of the unit.
Step 8 - Install rax pin into lowest pilot hole at each
end of nished back.
Step 9 - Snap end cap down onto rax pins, top of
endcap should be slightly below ush with top
of nished back.
Step 5 - Tilt the nished back upright to install the
raxes into the rax pins.
Step 6 - Tighten the raxes by reaching through the
unit from the front (top drawers will have to be
removed if the unit has them).
Illustration 8. Finished Back Installation Continued
8e. 8f.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 18 of 39

343-2950B (06/14)
Page 38 of 54
Involve Installation Packet
Step 1 – Place worksurface, with user surface down, on a clean carpeted surface or cardboard. Locate the
stanchion approximately 3" from the front and back edges of the worksurface; the stanchion should
be parallel and centered lengthwise along the depth of the worksurface. Position along the width of
the worksurface is dependent on the location of the mounting credenza and desired visual aesthetic.
Note: It is recommended that the worksurface have 18" or less of overhang when stanchion mounted.
When mounting to a 15" wide pedestal, the stanchion should be no more than 2" from the
outside edge of the worksurface.
Step 2 – Attach stanchion to worksurface using the provided wood screws. Once stanchion is secured to
worksurface, remove protective cover from one side of the mounting tape and apply to the bottom
surface of the stanchion. Place one strip at each end of the stanchion and the third strip centered
along the length of the stanchion.
Step 3 – Ensure credenza top is clean, dry and free of oils. Use two or more people to position stanchion onto
credenza top. Remove the protective cover from the mounting tape on the underside of the stanchion
and place stanchion onto credenza top.
Illustration 45. Worksurface Stanchion Installation
WARNING
Do not use worksurface stanchion without the mounting tape.
Failure to follow this warning could cause the worksurface
assembly to fall resulting in severe injury to yourself or others.
IMPORTANT: If spanning multiple units they must be
leveled and align end panel to end panel.
Step 3 - Place worksurface on top of support units
Aligning worksurface to be ush with the
trough and the end panels.
Step 1 - Locate high spots along support units
(Credenza, Wall Access Panel, False Ped).
Step 2 - Attach double sided tape strips to these
locations (high spots) along the run of the
worksurface.
Step 4 - Apply pressure to ensure strong bond between
worksurface and tape.
Step 5 - Let the top set for 24 hours before moving or
shifting the units.
Step 1 - Install glides into pedestal.
Step 2 - Install pulls onto fronts.
Step 3 - Set in place and level.
See leveling instructions.
Illustration 9. Worksurface Installation
9a. 9b.
Illustration 10. Single Pedestal & Double Pedestal Desks Installation
10a.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 19 of 39

NOTE: Freestanding desk should be in home
location before attaching second unit.
Step 1 - Install legs to worksurface using attached pilot
holes.
Step 2 - Set in place and level. See leveling instructions.
Step 1 - Screw modesty panel to external stiffener.
Step 2 - Screw through the modesty panel and thread
into external stiffener.
Step 3 - Place cover caps over counter-bore holes.
Step 1 - Screw brackets to freestanding desk
Step 2 - Align worksurfaces ush on top and end
Step 3 - Attach run-off desk to main worksurface
Step 4 - Set in place and level units.
See leveling instructions.
Step 5 - Verify the seams between the worksurfaces are tight.
Illustration 11. O-Leg Desk Installation
11a.
Illustration 12. Modesty Installation
12a.
Illustration 13. Attaching Run-off to Freestanding Desk / Worksurface
13a.
Laminate Casegoods Installation Packet
343-3942A
(8/16)
Page 20 of 39