Allsteel GZCKP User manual
Gallery Panels
Installation Instructions
Allsteel
Allsteel Inc.
Muscatine, Iowa 52761-0071
www.allsteeloce.com
Index
Systems Overview ................................ ............................2
Stride Panel System............................... ............................3
........................4
..........................6
......... ............................8
..................... ............................9
... ...........................11
Terrace Panel System ............................. ...........................12
.....................13
.......................15
.. ...........................17
...... ...........................18
..................... ...........................19
... ...........................21
Further ............................................ ...........................22
.. ...........................23
........ ...........................25
.................... ...........................27
Stride Benching ................................... ...........................28
...........................29
. ...........................31
Gallery to Gallery Connections............32
Glass installation ..................... ...........................36
Storage Connection ............................... ...........................36
......................... ...........................36
........................... ...........................38
Tackboard Installation ................... ...........................39
Hardware Chart ................................... ...........................40
Tools Needed:
Drill
3430455000 05/2020
Gallery Panels Installation Packet
Failure to install product as instructed, use of hardware other than that which is provided, or failure to comply
with instructions can result in product failure, personal injury, or property damage.
WARNING
3430455000Page 2 of 40
Systems Overview
Stride Further
Stride Benching
Stride Stride Benching Terrace Further
End of Run
Connector Kit
GZCKP GSBCKC,
GSBCKO
GTKCKP,
GTSKCKP
GFCHSH, GFCKA,
GFCKLH
Mid-Run Connector
Kit
GZ3CONxx, GCKPM Not Available GTK3CONxx, GCKPM Not Available
Panel Heights Oered in 30”H, 42.5”H,
50”H, and 57.5”H. Gallery
panel height must be within
30” of parent run height.
Oered in 30”H,
42.5”H, and
50”H.
Oered in 30”H, 42.5”H,
50”H, and 57.5”H. Gallery
panel height must be within
30” of parent run height.
Oered in 30”H,
42.5”H, and
50”H.
Panel Widths
End of Run
Dual-Sided (T)
Single Piece: 51”-84”
Two Piece (Split): 87”-147”
≥129” require worksurface
or storage tie-in on both
sides.
54”-84” Single Piece: 51”-84”
Two Piece (Split): 87”-147”
≥129” require worksurface
or storage tie-in on both
sides.
48”-84”
Panel Widths
End of Run
Single-Sided (L)
33”-84”
≥66” require worksurface
or storage tie-in.
33”-84” 33”-84”
≥66” require worksurface
or storage tie-in.
33”-84”
≥66” require worksurface
or storage tie-in.
Panel Widths
Mid-Run
18”-84”
≥63” require worksurface
or storage tie-in.
Not Available 18”-84”
≥63” require worksurface
or storage tie-in.
Not Available
Pilot Holes
Terrace
Gallery Panels Installation Packet
3430455000 Page 3 of 40
Create
Stride Panel System
Gallery Panels Installation Packet
3430455000Page 4 of 40
Stride End of Run Gallery Panel - Single Panel T & L Conguration
Step 2
Step 1
(H) x2
X
X
Note: Gallery panels can be installed before or after Stride panels are connected. Allsteel recommends attaching a
single spine panel to each gallery panel before connecting entire spine together. (See examples below...)
Recommended process
Note: Connector kits attach to sets of pilot holes found on the bottom of each gallery panel. End holes are used when
installing single-sided (L) applications; middle holes are used for dual-sided (T) applications. Installation of the
connector kits is the same for all hole locations.
(H) x4
If o-modular setup is
specied, measure spine
location from end of panel.
Use center slot to align
mounting bracket.
Gallery Panels Installation Packet
3430455000 Page 5 of 40
Create
Stride End of Run Gallery Panel - Single Panel T & L Conguration (Continued)
Step 3
Step 4
Step 5
Spacer Brackets
(E)
(F)
Add Spacer Brackets
above electrical hole
Remove Leveling
Block
Align bracket
into electrical
hole of frame.
Gallery Panels Installation Packet
3430455000Page 6 of 40
Stride End of Run Gallery Panel - Split Panel T Conguration
Note: A minimum of two people are required to properly install a split gallery panel due to product size and
assembly requirements. Product must lay at during installation. It is recommended to place panels on
blankets or cardboard to avoid damaging show surfaces.
Step 4
Step 5
Step 1
Step 2
Step 3
(H) x2
(H) x4
Spacer Brackets
Gallery Panels Installation Packet
3430455000 Page 7 of 40
Create
Stride End of Run Gallery Panel - Split Panel T Conguration (Continued)
Step 6
Step 8
Step 7
Note: For proper stability,
majority of weight should
rest on outer levelers.
Remove Leveling
Block
(F)
(E)
Align bracket
into electrical
hole of frame.
Add Spacer Brackets
above electrical hole
Connector Block
Gallery Panels Installation Packet
3430455000Page 8 of 40
Stride Mid-Run Blocks & Trim
Step 1
Step 3
Step 2
Step 4
(J)
Alignment
Block
Align bottom of trim
with bottom of raceway
Gallery Panels Installation Packet
3430455000 Page 9 of 40
Create
Stride Mid-Run Gallery Panel
Step 1
Note: Top bracket covers slotted
standard holes. If setup requires
an adjacent overhead storage
unit, attach top bracket 15” from
gallery panel top edge.
Step 3
Step 2
(B) x8
(B) x6
Gallery Panels Installation Packet
3430455000Page 10 of 40
Stride Mid-Run Gallery Panel (Continued)
Step 4
Step 5
Remove breakaway tabs
covering tile snap-in holes.
Bottom nger mounts into
lowest possible position.
Step 6
(I) x4
XX
Gallery Panels Installation Packet
3430455000 Page 11 of 40
Create
Stride Worksurface Connections
Note: Worksurfaces can connect to gallery panels with a Cantilever bracket or an L-Tower bracket.
Method is dependent on application specied.
Step 1
Cantilever Method
L-Tower Bracket Method
Note: Use of level is required when connecting worksurfaces with L-Tower bracket. Spine and gallery panels must
be level before worksurfaces are installed. All L-Tower bracket applications require additional panel-mounted
support to set worksurface height.
Step 1
Note: Worksurfaces with
unsupported spans
over 60” require two
L-Tower brackets.
Step 2
Step 3
Step 2
Step 3
(M) x9
(H) x2 Hole locations
Gallery Panels Installation Packet
3430455000Page 12 of 40
Terrace Panel System
Gallery Panels Installation Packet
3430455000 Page 13 of 40
Create
Terrace End of Run Gallery Panel - Single Panel T & L Conguration
Step 2
Step 1
X
X
Note: Gallery panels can be installed before or after Terrace panels are connected. Allsteel recommends attaching
a single spine panel to each gallery panel before connecting entire spine together. (See examples below...)
Recommended process
Note: Connector kits attach to sets of pilot holes found on the bottom of each gallery panel. End holes are used when
installing single-sided (L) applications; middle holes are used for dual-sided (T) applications. Installation of the
connector kits is the same for all hole locations.
(H) x2
(H) x4
If o-modular setup is
specied, measure spine
location from end of panel.
Use center slot to align
mounting bracket.
Gallery Panels Installation Packet
3430455000Page 14 of 40
Terrace End of Run Gallery Panel - Single Panel T & L Conguration (Continued)
Step 3
Step 4
Step 5
Spacer Brackets
Add Spacer Brackets
above frame horizontal
Remove Leveling
Block
(A)
(E)
Align bracket
into electrical
hole of frame.
Gallery Panels Installation Packet
3430455000 Page 15 of 40
Create
Terrace End of Run Gallery Panel - Split Panel T Conguration
Note: A minimum of two people are required to properly install a split gallery panel due to product size and
assembly requirements. Product must lay at during installation. It is recommended to place panels on
blankets or cardboard to avoid damaging show surfaces.
Step 4
Step 1
Step 2
Step 3
Step 5
Spacer Brackets
Add Spacer Brackets
above frame horizontal
Remove Leveling
Block
(H) x4
(E)
Gallery Panels Installation Packet
3430455000Page 16 of 40
Terrace End of Run Gallery Panel - Split Panel T Conguration (Continued)
Step 8
Step 6
Step 7
Note: For proper stability,
majority of weight should
rest on outer levelers.
Align mounting bracket
into frame electrical hole
(B) x8
(I) x4
Connector
Brackets x2
****IMPORTANT****
Do not cover tile lances
Top
Connector
Bottom
Connector
Gallery Panels Installation Packet
3430455000 Page 17 of 40
Create
Terrace End of Run Gallery Panel - 30H with Frameless Glass
Frameless Glass
30”H
Terrace
Panel
Gallery Panel
Note: The specic application shown below requires bracket kit GTKGK30 in order to properly install Frameless
Glass to a Terrace Panel connected to an End of Run Gallery Panel.
Frameless Glass bracket and
Gallery Panel connector interfere
within Terrace Vertical.
Step 1
Step 2
Step 3
(G) x4
Glass Adapter
Bracket
Gallery Panels Installation Packet
3430455000Page 18 of 40
Terrace Mid-Run Blocks & Trim
Step 1
Step 3
Connector Block
Step 2
Step 4
Fully seat into frames
with rubber mallet.
Must install BEFORE top
trim of Terrace frames.
(E)
Gallery Panels Installation Packet
3430455000 Page 19 of 40
Create
Terrace Mid-Run Gallery Panel
Step 1
Note: Top bracket covers slotted
standard holes. If setup requires
an adjacent overhead storage
unit, attach top bracket 15” from
gallery panel top edge.
Step 3
Step 2
(B) x8
(B) x6
(I) x4
Gallery Panels Installation Packet
3430455000Page 20 of 40
Terrace Mid-Run Gallery Panel (Continued)
Step 4
Step 5
Remove breakaway tabs
covering tile lead-in holes.
Bottom nger mounts into
second lowest possible position.
Step 6
This manual suits for next models
7
Table of contents
Other Allsteel Indoor Furnishing manuals
Allsteel
Allsteel Park NA96RCF User manual
Allsteel
Allsteel Cadence Applica Freestanding Desk User manual
Allsteel
Allsteel Involve KAPE-E Service manual
Allsteel
Allsteel Laminate Casegoods User manual
Allsteel
Allsteel Universal Screens User manual
Allsteel
Allsteel Further Series User manual
Allsteel
Allsteel Park User manual
Allsteel
Allsteel Park Easel Service manual
Allsteel
Allsteel Trooper User manual
Allsteel
Allsteel Optimize Service manual
Allsteel
Allsteel A8 User manual
Allsteel
Allsteel Townhall Series User manual
Allsteel
Allsteel Further User manual
Allsteel
Allsteel Park Series User manual
Allsteel
Allsteel MERGE Service manual
Allsteel
Allsteel Harvest Rustic Standing Height Table User manual
Allsteel
Allsteel Approach User manual
Allsteel
Allsteel Quip User manual
Allsteel
Allsteel Terrace DNA User manual
Allsteel
Allsteel Access User manual
Popular Indoor Furnishing manuals by other brands
Cecilware
Cecilware WT4-2448 Assembly instructions
Baxton Studio
Baxton Studio Queen Bed 0049 Assembly instructions
Sport-thieme
Sport-thieme 131 6201 Operating & assembly instructions
SUNVILLA
SUNVILLA 2127143 Assembly / care & use instructions
Garden Trading
Garden Trading Talland TLPC01 Assembly instructions
OSP Home Furnishings
OSP Home Furnishings FWK43 manual
Novogratz
Novogratz 3942500COM manual
TRICA
TRICA Q-WIS-200 manual
Clinton
Clinton 74-14H OPERATION, CARE & MAINTENANCE
Living Earth Crafts
Living Earth Crafts Nuage Series user manual
Cooper Lighting
Cooper Lighting Halo LZR51017 Specification sheet
Germania
Germania Garderobenpaneel 3028 Assembly instruction
Furniture of America
Furniture of America CM-AC228 Assembly instructions
BLACK RED WHITE
BLACK RED WHITE re set adgz 4/15 Assembly manual
Core Products
Core Products Corona CR912 Instruction leaflet
Glorious
Glorious Turntable Lowboard Assembly instructions
Kenroy Home
Kenroy Home KHAL 65095 Use and care guide
JWA
JWA 68559 Assembly instruction