Allsteel Park NA96RCF User manual

Park
Installation Instructions
Allsteel Inc.
Muscatine, Iowa 52761-0071
www.allsteelofce.com
Index
96” Racetrack Conference Table, NA96RCF
Kit of Parts . . . . . . . . . . . . . . . . . . . . . 2
Noteables . . . . . . . . . . . . . . . . . . . . . . 2
Assembly . . . . . . . . . . . . . . . . . . . . . . 3
Worksurface Attachment . . . . . . . . . . . . 3
Electrical Attachment . . . . . . . . . . . . . . 4
Layered Conference Table, NALCF
Kit of Parts . . . . . . . . . . . . . . . . . . . . . 4
Noteables . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . 5
Worksurface Attachment . . . . . . . . . . . . . 6
Electrical Attachment . . . . . . . . . . . . . 6
48” Freestanding Table, NA48SS/NA48R
Kit of Parts . . . . . . . . . . . . . . . . . . . . . 7
Noteables . . . . . . . . . . . . . . . . . . . . . . 7
Assembly . . . . . . . . . . . . . . . . . . . . . . 7
Worksurface Attachment . . . . . . . . . . . . 8
Electrical Attachment . . . . . . . . . . . . . 8
Fastener Chart . . . . . . . . . . . . . . . . . . . . . . . 9
Page 1 of 9

Illustration 1a: Kit of Parts - 96” Racetrack Conference, NA96RCF
Short Leg
Stretcher Bar Top Angled Crossbeam
Installation Packet
Failure to install product as instructed, use of hardware other than that which is provided, or failure to comply
with instructions can result in product failure, personal injury, or property damage.
WARNING
Park
3430408700Pages 2 of 9
Illustration 1b: Noteables
LH RH
Short Leg
*Important- Right hand and Left hand for some parts.
*Screw appearance - When installed correctly, screws are countersunk. Reference image below.

Step 1 - Complete Assembly while inverted on a clean, dry surface.
Step 2 - On one side, slide the Top Crossbeams into the respective spots on the Short Legs and secure with 4 A
screws. Next, slide the Stretcher Bar onto respective barstock and secure with 4 Ascrews. Make sure to
support the opposite end of the Pitchfork during installation.
Step 3 - Repeat Step 2 on the other side, securing with 8 Ascrews.
Step 1 - Place worksurface topside down on a clean, dry surface. Place assembled base on top.
Step 2 - Align pilot holes on the underside of the worksurface. Use 24 Bscrews to attach base to worksurface through
attachment plate. Stand unit upright and adjust levelers.
*** All pilot holes must have a fastener installed***
Support pitchfork
during installation
Installation Packet
Create
Park
3430408700 Page 3 of 9
Illustration 1c: 96” Racetrack Conference Table Assembly
350-1675
A x 16
Illustration 1d: Worksurface Attachment
B x 24
23

Step 1 - Determine locations for the slide mount on the underside of the worksurfaces. Reference images below for
suggested locations.
Step 2 - Install Slide Mount to the underside of the worksurface with given hardware and insert Minitap. Use provided
clips to hold Nodes to bottom of worksurface.
Step 3 - Use Cable Management Straps (C) to secure excess cord to frame.
11
11
11
11
Node Cable Management
Strap
Installation Packet
Page 4 of 9 3430408700
Park
Illustration 2a: Kit of Parts - Layered Conference, NALCF
Tall Leg A- Frame Stretcher Bar Top Crossbeam Short Leg
*Important- Right hand and Left hand for some parts
Top Crossbeam
LH RH
Illustration 2b: Noteables
Illustration 1e: Electrical Attachment - Optional
LH RH
Short Leg
Cable Management
Bracket
*Screw appearance - When installed correctly, screws are countersunk. Reference image below.
Node Clip
Slide Mount

Step 1 - Complete Assembly while inverted on a clean, dry surface.
Step 2 - Connect the Tall Leg and A-Frame with 4 Ascrews.
Step 3 - Connect the Stretcher Bar and Top Angled Crossbeam to Short Legs using 8 Ascrews.
Step 4 - Join the two subassemblies with 6 Ascrews.
SCALE 0.080
SCALE 0.070
Support pitchfork
during installation
Installation Packet
Create
3430408700 Page 5 of 9
Park
Illustration 2c: Layered Conference Table Assembly
350-1675
A x 18
2 3

Step 1 -Place assembled base right side up and place round worksurface on top. Align pilot holes and use 6 Bscrews
to attach worksurface. Make sure that the screws in the A-Frame are fully seated.
Step 2- Place the pill shaped worksurface on the base. Align pilot holes and use 24 Bscrews to attach base to
worksurface from underside of the table. Adjust levelers.
B x 32
Step 1 - Determine locations for the slide mounts on the underside of the worksurfaces. Reference images below for
suggested locations.
Step 2 - Install Slide Mounts to the underside of the worksurface with given hardware and insert Minitap. Use provided
clips to hold Nodes to bottom of worksurface.
Step 3 - Install Cable Management Bracket in desired location using 2 BScrews.
Step 4 - Use Cable Management Bracket to wrap up excess cord and use Cable Management Straps (C) to secure.
*** All pilot holes must have a fastener installed***
Node
Node Clip
Slide Mount
II
II
II
II
B x 2
Installation Packet
Page 6 of 9
Park
3430408700
Illustration 2d: Worksurface Attachment
Illustration 2e: Electrical Attachment - Optional
Cable Management
Strap

Step 1 - Complete Assembly while inverted on a clean, dry surface.
Step 2 - Insert the Stretcher Bar onto Short Legs, align holes and secure using 4 Ascrews. Support opposite end of
pitchfork during installation.
Step 3 - Repeat Step 2 on the other side.
Short Leg Stretcher Bar
RHLH
*Screw appearance - When installed correctly, screws are countersunk. Reference image below.
Installation Packet
Create
Page 7 of 9
Park
3430408700
Illustration 3a: Kit of Parts - 48” Freestanding, NA48SS/NA48R
Illustration 3c: 48” Freestanding Table Assembly
350-1675
A x 8
Illustration 3b: Noteables
*Important- Right hand and Left hand for some parts
Short Leg
23
Support pitchfork
during installation

Illustration 3e: Electrical Attachment - Optional
B x 16
Step 1 - Place worksurface topside down on a clean, dry surface. Place assembled base on top.
Step 2 - Align pilot holes on the underside of the worksurface. Use 16 Bscrews to attach base to worksurface through
attachment plate. Stand unit upright and adjust levelers.
*** All pilot holes must have a fastener installed***
Step 1 - Determine locations for the slide mount on the underside of the worksurfaces. Reference images below for
suggested locations.
Step 2 - Install slide mount to the underside of the worksurface with given hardware and insert Minitap. Use provided
clips to hold Nodes to bottom of worksurface.
Step 3 - Use Cable Management Straps (C) to secure excess cord to frame.
Node
Node Clip
Slide Mount
Installation PacketPark
3430408700Page 8 of 9
Illustration 3d: Worksurface Attachment
Cable Management
Strap

Installation Packet
Create
Page 9 of 9
Park
3430408700
A B
350-1675 50-2560
350-1675
Illustration 4: Fastener Chart
*** All screws printed to 1:1: scale ***
1/4-20 x 5/8” Flat Socket Cap Screw (A) #10 x 7/8 wood screws (B)
Cable Management
Strap (C)
350-1691
C