Allsteel Park Easel Service manual

Park
Installation Instructions
Allsteel Inc.
Muscatine, Iowa 52761-0071
www.allsteelofce.com
Index
Easel, NAESL
Kit of Parts . . . . . . . . . . . . . . . . . . . . . . 2
Notables . . . . . . . . . . . . . . . . . . . . . . . 2
Assembly . . . . . . . . . . . . . . . . . . . . . . . 3
TV Attachment . . . . .. . . . . . . . . . . . . . 4
Electrical Attachment . . . . . . . . . . . . . . . 5
Liner Placement . . . . . . . . . . . . . . . . . . . 5
Fastener Chart . . . . . . . . . . . . . . . . . . . . . . . . . 6
Page 1 of 6

Illustration 1: Kit of Parts - NAESL
*Important- Right hand and Left hand parts for certain parts
SCALE 0.200
42”- 46”
50”- 55”
60” and up
Easel Arch
Easel Side Leg
Easel Tray Easel TV Tray
Easel Side Leg
Easel Insert
Easel Tall Leg
RHLH
Easel Caster
SCALE 0.150
Installation Packet
Failure to install product as instructed, use of hardware other than that which is provided, or failure to comply
with instructions can result in product failure, personal injury, or property damage.
WARNING
Park
3430408900Pages 2 of 6
Illustration 2: Noteables
*SuggeSted tV tray LocatIonS BaSed on tV SIze -Top Hole: 42”- 46”,Middle Hole: 50”- 55”, Bottom Hole: 60” and up
*Screw appearance - When installed correctly, screws are countersunk. Reference image below.

Step 1 - Rest the back end of Easel Tray on a clean, dry surface. Tilt Tray to one side and insert RH/LH Leg
Assemblies into respective locations. Align holes and use 4 Ascrews to secure in place.
Step 2 - Place Easel Arch with attached Easel Inserts onto the RH and LH leg assembly. Align holes and use 2 A
screws to secure Arch to Legs. Ends of tube should line up, refer to Noteables.
Step 3 - Stand the assembly up and insert Easel Back Leg into respective locations on Arch and Leg Assembly. Align
holes and secure with 3 Ascrews.
Step 4 - Select desired location for Easel TV Tray and secure with 2 C screws and 2 B washers. Refer to Noteables for
location suggestion.
Step 5 - Insert casters to the stems already attached to side and back legs. Apply ample pressure until caster snaps
into stem
Installation Packet
Create
Park
3430408900 Page 3 of 6
Illustration 3a: Easel Assembly
350-1675
350-1727
C x 2
A x 9
B x 2
350-0850
Ax4
A x2
A x3
B x2 C x2
1
2
34
5

Step 1 - Align holes on electrical unit with holes on the TV Tray.
Step 2 - Insert Gscrews through the top of the TV Tray and electrical unit and secure underneath tray with acorn nut
(H).
Step 3 - Use Cable Management Straps (I) to secure excess cord to frame.
Step 1 - Place rubber mats in respective tray locations after full assembly.
G x4
H x4
Installation PacketPark
Page 4 of 6 3430408900
Illustration 3b: Electrical Attachment - Optional
GH
Illustration 3c: Liner Placement
1
2
3

SCALE 0.250
*** Brackets angled to conform and lock to prole of tube ***
Installation Packet
Create
Park
Page 5 of 63430408900
Illustration 3d: Easel TV Attachment
Step 1 - Gently place TV screen down on a clean, solid surface.
Step 2 - Choose the appropriate screws (2 Dor 2 E) and number of washers (1-4 F) according to the type of screen/TV.
Determine the placement of the mounting bracket by nding the upper most mounting hole.
Step 3 - Thread bolt and washers through the slot in the mounting bracket then into the mounting hole in the back of the
TV, loosely tighten bolts to secure bracket. DO NOT OVERTIGHTEN. DO NOT USE A POWERDRILL
Step 4 - Place TV on the TV tray. Slide bracket to proper position on the arch. Gently tighten screws the rest of the way
to secure TV into place.
D x 2 E x 2 F x 8
WARNING:
TV SIZES 42” AND UP
TV MUST BE VESA MIS-F COMPLIANT: 200x200 to 600x400
DO NOT OVERTIGHTEN. DO NOT USE A POWERDRILL.
DO NOT ATTEMPT TASK ALONE

Installation PacketPark
3430408900Page 6 of 6
A B C D
350-1727
E
350-1675 350-0850 4021-816 350-1732 350-1730
350-1675
350-0850
Illustration 4: Fastener Chart
*** All screws printed to 1:1: scale ***
1/4” Washer (B)
M6 25MM Screw (E)
M8 25MM Screw (D)
1/4”-20 X 1.25” Pan Head Screws (C)
1/4-20 x 5/8” Flat Socket Cap Screw (A)
M8 Washer (F)
350-1733
F
10-32 x 7/16” Flat Head Machine Screw (G)
350-1234
G
10-32 Acorn Nut (H)
783-850
H
Cable Management
Strap (I)
350-1691
I