Allsteel Universal Screens User manual

Universal Screens
Installation Instructions
Index
Screen Overview .................................. ............................2
U - Bracket Installation ............................ ..........................3-6
1. Side Mount Lateral (ADMBFS | ADMBGS)
2. Front to Back Lateral (ADMBFF | ADMBGF)
3. Top Mount Lateral (ADMBGT | ADMBFT)
4. Further Center Beam (ABMBLF | ABMBLH)
5. Elevated (ADMBAH | ADMBAF)
6. Sit on Surface (ADMBSH | ADMBSF)
Above/Below Installation (ADMBDA | ALS27##DFS | AFS####DFS | AAS27##DFS) ..........7-8
Further Modesty Screens-Fabric (ABMBBM).......... ............................9
Fabric Modesty Screens (AFS13##MPD)............... ...........................10
Laminate Modesty Screens (ALS13##MPD) ............ ...........................10
Acrylic Modesty Screens (ADMBMA) ................. ...........................11
Glass Modesty Screens (ADMBDS)................... ...........................11
Alignment Clip Installation ........................ ...........................12
Hardware Chart ................................... ...........................13
Muscatine, Iowa 52761-0071
www.allsteelo󰀩ce.com
Allsteel
Tools Needed:
1/8” Allen Wrench
Drill
Tape Measurer
#2 Phillips Driver
1/4” Hex Driver
Driver Extension
1430120200_A 07/2022

NOTE: Not all congurations shown.
Side Mount Lateral Top Mount Lateral Front to Back
Above/Below Acrylic Modesty Glass Modesty (Above/
Above & Below)
Further Fabric
Modesty
Further Fabric
Universal Screens Installation Packet
1430120200_APage 2 of 13
Screen Overview
NOTE: Most Universal Screen Bracket types
include a U-Bracket sub assembly
(shown to the right). The gap width will
vary depending on whether it is a fabric
or hard surface model.
Bracket Type A
Fabric 7/8”
Hardsurface 3/8”
A

Universal Screens Installation Packet
1430120200_A Page 3 of 13
U-Bracket Installation
NOTE: Steps 1 - 7 are applicable to all U bracket models unless otherwise noted.
Step 1 - 
of the bracket.
Verify that set


inside face of
bracket.
Step 2 - Place brackets on worksurface. Brackets should be positioned so that they are approximately 6 inches in from the edge of
the screen after the screen is installed.
6”
6”

Universal Screens Installation Packet
1430120200_APage 4 of 13
U-Bracket Installation (Continued)
Step 3a - Position U-brackets in desired locations. Secure to worksurface

Tape
Top Mount Lateral
ADMBGT
ADMBFT
Step 3a - Attach tape to bottom of bracket. Mount brackets in desired
location and apply pressure for 15 seconds.
C
Select the appropriate Step 3 below for your specic bracket type. Model numbers listed as reference.
Side Mount Lateral
ADMBFS
ADMBGS
Step 3a - Align Bracket on surface and tighten (2) bottom set screws per
bracket with 1/8” Allen Wrench
Step 3a - Align Bracket on surface and tighten (2) bottom set screws per
bracket with 1/8” Allen Wrench
Front to Back Lateral
ADMBFF
ADMBGF
A
Note:
Top Mount Lateral brackets can
be installed using
tape OR screw method

Universal Screens Installation Packet
1430120200_A Page 5 of 13
Step 3a - Attach 2 urethane pads to the bottom of each bracket in the
approximate location shown.
Sit on Surface
ADMBSH
ADMBSF
Urethane
Pad
Elevated
ADMBAH
ADMBAF
Step 3a - Secure to surface using (4) #10 x 7/8” Hex Head wood screws
per bracket.
B
U-Bracket Installation (Continued)
Step 3b - o
then tighten screw.
Further Center Beam
ABMBLF
ABMBLH
Step 3a - Slide the cinch tabs of the U-bracket assembly into the slot along the beam. Loosen the cinch tab screws so that the tabs rotate freely and
then retighten the screw to rotate and lock the cinch tabs in place.
Loosen cinch
tab screws

Universal Screens Installation Packet
1430120200_APage 6 of 13
Step 4 - Carefully insert screen into U-Bracket and ensure that
the screen is fully seated. Verify that the brackets are
positioned approximately 6” from both ends of the
screen.
Step 6 - Use 1/8” Allen wrench to tighten set
screws evenly against screen.
Step 5 - 
of the U bracket and the screen on the
side with the set screws.
Step 7 - Attach magnetic covers to exposed side
of bracket.
6”
Turn set screws
clockwise to tighten
against screen.
U-Bracket Installation (Continued)

Universal Screens Installation Packet
1430120200_A Page 7 of 13
Above/Below Screens
B
Step 1 - Slide brackets on both ends of the screen
in desired location and secure by turning
the thumb screw clockwise.
Step 2 - Position the screen in the desired location
on the worksurface. Attach mounting
brackets by installing (4) #10 x 7/8” Hex
Head screws.
Step 1 - 
it is straight before securing the second bracket.
 
worksurfaces with (4) #10 x 7/8” Head Head Screws per bracket.
Adjustable Fabric Screens
ADMBDA
Fixed Fabric Screens
AFS####DTS
B

Universal Screens Installation Packet
1430120200_APage 8 of 13
Step 1 - Attach (2) Mounting Brackets at pilot holes in
Arylic Panel using (4) 10-24 x 3/8” Flat Head
Machine Screws per bracket. Then attach
front cap bracket on other side of panel.
Step 2 -
then look down the edge of the panel to verify that it is
straight before securing the second bracket.
 
second bracket to straighten it out. Each bracket attaches
to worksurfaces with (4) #10 x 7/8” Head Head Screws per
bracket.
B
G
Step 1 - Attach (2) Brackets at pilot holes in Laminate Panel using (6) #10 x 3/4” Hex Head
Screws (H) per bracket.
Step 2 -
edge of the panel to verify that it is straight before securing the second bracket.

straighten it out. Each bracket attaches to worksurfaces with (6) #10 x 7/8” Hex
Head Screws (I) per bracket.
NOTE:
Ensure
correct
screw is
used for
each step
as to not
damage
screen
H
I
Above/Below Screens (Continued)
Laminate Screens
ALS27##DFS
Acrylic Screens
AAS27##DFS

Universal Screens Installation Packet
1430120200_A Page 9 of 13
Create
Modesty Screens
1-3/4”
Step 2 - Slide the cinch tabs of the large U bracket assembly into the slot along the underside of the beam. Loosen the cinch
tab screws so that the tabs rotate freely and then retighten the screw to rotate and lock the cinch tab in place.
Step 3 - Align the small and large U brackets and slide the screen up into the beam until the magnets engage.
Nest cinch
tabs into
slot along
base of
beam.
Step 1 - Mount small U brackets to the bottom of the fabric screen so that the edge of the bracket coincides with the edge of the
corner radius (approximately 1-3/4” in from the ends). Secure brackets by driving (2) #8-18 Flat Head screws per bracket
into the center seam of the screen. Do not overtighten.
I
Further Modesty Fabric Screen
ABMBBM

Universal Screens Installation Packet
1430120200_APage 10 of 13
Modesty Screens (Continued)
Fabric Screens
AFS13##MPD
Step 1 - 

second bracket to straighten it out. Each bracket attaches to worksurfaces with (3) #10 x 7/8” Head Head Screws
per bracket.
Step 1 - Attach (2) Brackets at pilot holes in Laminate Panel using (4) #10 x 3/4” Hex Head Screw per bracket (H).
Step 2 -

second bracket to straighten it out. Each bracket attaches to worksurfaces with (3) #10 x 7/8” Head Head
Screws per bracket (I).

B
I
H
NOTE:
Do not overtighten
screws as to not
damage screen
Laminate Screens
ALS13##MPD

Universal Screens Installation Packet
1430120200_A Page 11 of 13
Create
Modesty Screens (Continued)
Step 1 - Attach mounting brackets to screen using (2) #8 X 1/2” pan
head screws and (2) washers per bracket.
Step 2 -
then look down the edge of the modesty panel to verify
that it is straight before securing the second bracket. If the

bracket to straighten it out.
F

NOTE:
Do not overtighten
screws as to not
damage screen
Acrylic Modesty
ADMBMA
Step 1 - Slide brackets over both ends of the glass panel until
glass is full seated in the bracket.
Step 2 -
modesty panel to underside of worksurface using (6) #12-8 x 1”
Pan Head screws per bracket.
D
Glass Modesty
ADMBDS

Universal Screens Installation Packet
1430120200_APage 12 of 13
Alignment Clip Installation
Glass Alignment Clip
Step 1 - Cap alignment over the seam where two glass panels are

Note: Alignment Clips only applicable for in-line applications
Step 1 - 
Step 2 - Press screens together around alignment clip until set at desired location.
Fabric Alignment Clip
Fabric Alignment Clip
Glass Alignment Clip

Universal Screens Installation Packet
1430120200_A Page 13 of 13
Create
Hardware Chart
B
Hex Head
0500256000
A1/4-20 UNC Thread
1/8” Hex Set Screw
3500106500
C#10 X 1”
Flat Head
3500005000
D#12-8 X 1”
Phillips Pan Head Screw
3500081400
E#8 X 1/2”
Phillips Pan Head Screw
3500024800
F#10 x 3/4”
Hex Head Screw
0500057900
G#10 x 7/8”
Hex Head Screw
0500256001
10 - 24 x 3/8”
Flat Head Machine Screw
0500320300
H
#8-18
Flat Head Screw
0500248400
I